Installation Instructions

ManualsBrandsOPTX 20/20 ManualsGrocery & HomeHydrotac™ Stick-On Bifocal Lens + 2.00

1 Carefully wash the lenses of your glasses with

an oil-free soap and allow them to dry.

2 Using warm water, place a drop of water inside

the lens of your glasses where you are going to

apply the

Hydrotac

lens.

3 Take a Hydrotac lens and place it on the

inside of the lens, making sure the curve of

the Hydrotac lens matches the curve of your

glasses. Hydrotac lens can be positioned

anywhere on your eyeglass lens. Hydrotac

lenses should be in the same position, both

horizontally and vertically on either lens of your

glasses. You can reposition the lenses as long

as they are still moist. Repeat this operation

with the second lens.

4 Using a lint-free cloth, gently press the Hydrotac

lenses to force out any excess water.

Wear your glasses and make sure your long-

distance sight is not obstructed by the Hydrotac

lens.

If your line of vision is obstructed, remove the

lenses using your ﬁngernail. Reposition the lenses

as instructed in Steps 2 through 4 above.

If you require the Hydrotac lenses to be smaller,

use a sharp scissors to trim the lenses from the

lower-curved side. Then, install the lenses as

instructed in Steps 2 through 4 above.

While the lenses are fixed to your glasses,

complete molecular adhesion will occur in

approximately 24 hours. You can always remove

Hydrotac lenses using your ﬁngernail to lift the

edge.

Hydrotac lenses do not leave any residue behind

and can be removed and reused as often as you

require.

APPLICATION INSTRUCTIONS

WET

POSITION

WIPE

EVERY HYDROTAC

LENS IS DESIGNED AND

MANUFACTURED IN THE

UNITED STATES

STICK-ON BIFOCAL LENSES

Hydrotac is a registered trademark of Neoptx LLC.

Neoptx, 3201 Commerce Pkwy Miramar, FL 33025

1 800 344 2020 optx2020.com

Protected by US & foreign patents.

HYDROTAC

1.25

Summary of content (7 pages)

PAGE 1
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 2
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 3
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 4
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 5
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 6
APPLICATION INSTRUCTIONS WET 1 Carefully wash the lenses of your glasses with an oil-free soap and allow them to dry. 4 Using a lint-free cloth, gently press the Hydrotac lenses to force out any excess water. 2 Using warm water, place a drop of water inside the lens of your glasses where you are going to apply the Hydrotac lens. Wear your glasses and make sure your longdistance sight is not obstructed by the Hydrotac lens.
PAGE 7
INSTRUCTIONS AND PRECAUTIONARY NOTES FOR USE // PLEASE READ CAREFULLY BEFORE USE // Hydrotac® lenses are created with the same magnification used to correct Presbyopia (simple far sightedness) and for reading. Hydrotac lenses can be mounted to sunglasses, safety glasses, welding masks, diving masks, sporting glasses or any other type of eyewear. Hydrotac lenses are not intended to be used when driving a car or motor vehicle. Keep Hydrotac lenses out of the reach of young children.