Operation Manual

15
Oral-B Sensitive brush head
features an extra soft bristle structure
that is gentle on teeth and gums.
Oral-B Precision Clean brush head
cups each tooth with a curved bristle
trim and reaches deep between teeth
at the same time.
Oral-B 3D White brush head
features a special polishing cup to
naturally whiten your teeth. Please
note that children under 12 years old
should not use the Oral-B 3D White
brush head.
Oral-B PowerTip brush head
offers a deep clean in hard to reach
areas, e.g. around bridges, crowns or
implants.
Our dynamic TriZone brush head can be used with
all common brushing techniques.
Oral-B TriZone brush head
features triple zone cleaning action
for outstanding plaque removal, even
in between teeth.
Oral-B brush heads feature light blue INDICATOR
®
bristles to help you monitor brush head replace-
ment need. With thorough brushing, twice a day for
two minutes, the blue color will fade halfway down
approximately in a 3-month period. If the bristles
splay before the color recedes, you may exert too
much pressure on teeth and gums.
We do not recommend using the Oral-B FlossAction
or Oral-B 3D White brush head with braces. You
may use the Oral-B Ortho brush head, specifically
designed to clean around braces and wires.
Synchronizing your
toothbrush
To avoid interference of display messages when
using more than one Oral-B Black 7000 toothbrush
with SmartGuide in the same household, you need to
assign the handles to their respective SmartGuide.
You can synchronize a maximum of 2 handles with
one SmartGuide. To do so, push the «h/min» button
in the battery compartment for at least 3 seconds.
The SmartGuide shows «L---». Turn on your handle
to start the synchronization process. It is finished
when «L-1-» is displayed. Turn off the handle. To
assign a second handle to the same SmartGuide
turn on the other handle until «L-2-» is displayed.
After having synchronized the second handle, «Full»
will be displayed. Exit the synchronization mode by
pressing the «h/min» or «set» button, otherwise it
will end automatically after 30 seconds.
Cleaning recommendations
After brushing, rinse your brush head under running
water with the handle switched on. Switch off and
remove the brush head. Clean handle and brush
head separately; wipe them dry before reassembling.
Disassemble the charging unit before cleaning.
Brush head compartment and protective cover
are dishwasher-safe. Both basic charger and
SmartGuide should be cleaned with a damp cloth
only. When cleaning the travel case (m) take out the
inner part. The inner part is dishwasher-safe; the
outer case should be cleaned with a damp cloth only
(picture 5, page 5).
Make sure the parts are completely dry before
reassembling the travel case again.
Note: Clean stains on the travel case surface
immediately. Store travel case in a clean and dry
place.
Wall mount
Use the adhesive ring (l) with the wall mount (k) if
you prefer to mount the SmartGuide on a wall,
mirror or other surface. Make sure the chosen
surface is clean and dry before adhering.
Stick the adhesive ring on the even side of the wall
mount and press it firmly to the wall. Wait 24h
before sliding the SmartGuide holder (j) into the
fixed wall mount. Place the SmartGuide into its
holder (picture C, page 4). The adhesive ring will
not work on dirt-repellent surfaces.
Subject to change without notice.
This appliance complies with the require-
ments covered by the European Directive
1999/5/EC. Receiver Class 3, Duty Cycle
Class 3. To find the complete EC declaration of
conformity, please visit www.oralb.com/ce.
92036479_D34_WE_7000_S6-68.indd 15 19.12.12 13:49
CSS APPROVED Effective Date 27Dec2012 GMT - Printed 05Mar2013 Page 14 of 67