Manualshelf

User's Guide

ManualsBrandsOrbic ManualsComputers & AccessoriesOrbic Speed (Wireless router with LTE, WCDMA, WIFI)
12
Getting Started：
Thank you for choosing Orbic
Speed 4G LTE mobile hotspot
device.
Note:
This User Guide provides the basic
operations of the Orbic Speed.
General Appearance
1. Menu button
2. Signal status icon
3. Network mode icon
4. Wi-Fi signal icon
5. Unread message icon
6. Battery icon
7. Power button
8. USB Type C port
9. Battery cover
10. Cutout to remove back cover
Display Layout and Icons
Quick Start
Guide
1 2 3 4 5 6
Description
1. Signal status icon
2. Network mode icon
3. Send/receive data activity arrows
4. Wi-Fi signal and number of access users
5. The number of unread message
maximum is 100
6. Battery capacity icon, if battery capacity
is lower than 25%, this icon is red.
7. Data statistics, used/total
SIM Card and Battery
Your Orbic Speed comes preinstalled with a 4G LTE SIM card.
Notes:
• The SIM card MUST remain in your Orbic Speed when in
use. Once the SIM card has been inserted into the Orbic
Speed, do not remove!
• DO NOT remove SIM card when the device is powered on
since this may damage the card and the device.
• Do not bend or scratch your SIM card. Avoid exposing your
SIM card to static electricity, water or dirt.
Removing the 4G LTE SIM Card
1. Power off the Orbic Speed. Remove the battery cover and take out
the battery.
2. Gently remove the SIM card from the SIM card slot
Setting up Wi-Fi connection
1. Press and hold the “power” button for 3 seconds until the welcome
logo is displayed on the Screen, and Wi-Fi is on.
2. Use your terminal devices to search the wireless network
connection with the Wi-Fi’s SSID of “4G-WIFI-2.4G-xxxx ”or
“4G-WIFI-5G-xxxx ” and click “Connect”. If the security mechanism
is applied, you need to enter the correct PASSWORD.
Note: xxxx is the last 4 digits of device MAC.
The default password is 10000XXX (XXX is the last three digits of IMEI).
You can also find the default SSID and Password in the WIFI Info page of
Orbic Speed screen.
Setting up your WPS
If your terminal devices support WPS, you do not have to input the
password manually once your WPS has been set up. To use WPS please
follow these steps:
1. Enable WPS in the WebUI through Settings->Wireless->WLAN
Settings->WPS
2. Press “Menu” button on the device to select “WPS Active”page on
the SCREEN
3. Press “Power” button to active WPS function
Then you can enable the WPS function on your terminal to connect the
hotspot.
How to change the SSID & Password
1. Log in to http://192.168.1.1 or http://my.jetpack and enter the
management page.
2. Select Settings> Wireless> WLAN Settings, then you will see “Wi-Fi
Name(SSID) ” and “Password”, Make sure you delete the old name
and password and enter the new name and password as you
require.
3. Select “Apply” button, wait for the screen to display prompting
“Success”, and then log out.
4. Wait for the computer or laptop screen to display the Wi-Fi icon.
This means the wireless network connection has been successful.
Inserting and Charging the Battery
1. Use the thumb catch at the bottom of your Orbic Speed to open
the battery cover and align the battery contacts with the terminals
in the battery compartment as shown. Push the battery down until it
clicks into place. (Figure 1 and 2)
2. Place the battery cover over the battery compartment and press it
downward until it clicks into place. (Figure 3)
3. Your Orbic Speed comes with charger. To charge: Plug one end of
the charger into an electrical outlet and the other end into the Orbic
Speed Type-C Port. (Figure 4)
Figure 3
Figure 1 Figure 2
Figure 4
7
FCC ID:2ABGH-RC400L

Summary of content (2 pages)