Manual

ManualsBrandsORBIT FR ManualsEquipmentPerformance Series AZ, EL Positioners: Heavy Duty

132

Coaxial single-channel rotary joint options include an

internal RF path, an RJ mounting ﬂ ange, and appro-

priate RF bulkhead connectors. Electrical travel limits

remain but are typically disabled when this option is

purchased.

LOWER AXIS USAGE

• RJ12L – DC-12.4 GHz, N-Type Connector

• RJ18L – DC-18 GHz, SMA-Type Connector

• RJ26L – DC-26.5 GHz, SMA-Type Connector

• RJ40L – DC-40 GHz, K-Type Connector

• RJ50L – DC-50 GHz, 2.4 mm Connector

UPPER AXIS USAGE

• RJ12U – DC-12.4 GHz, N-Type Connector

• RJ18U – DC-18 GHz, SMA-Type Connector

• RJ26U – DC-26.5 GHz, SMA-Type Connector

• RJ40U – DC-40 GHz, K-Type Connector

• RJ50U – DC-50 GHz, 2.4 mm Connector

Ordering Guide

for Factory-Installed Options

encoder options

Encoder options are available for customers desiring

high accuracy positioning or for applications involving

DSP-based motion control systems. These options are

offered in incremental or absolute formats and replace

the standard synchro assembly.

• EN001 – Standard Accuracy, Rotary Incremental

• EN002 – High Accuracy, Direct-Drive Incremental

• EN003 – High Accuracy (EnDat

format), Direct-Drive

Absolute

• EN004 – Standard Accuracy (EnDat

format), Rotary

Absolute

EN001

(Left to Right) RJ40, RJ18, RJ12

rotary joint options

Summary of content (5 pages)

PAGE 1
> Ordering Guide for Factory-Installed Options encoder options Encoder options are available for customers desiring high accuracy positioning or for applications involving DSP-based motion control systems. These options are offered in incremental or absolute formats and replace the standard synchro assembly.
PAGE 2
slip ring options LOWER AXIS USAGE • SR051L • SR101L • SR201L • SR301L • SR402L • SR502L • SR602L • SR512L • SR812L – 5 Contact – 10 Contact – 20 Contact – 30 Contact – 40 Contact – 50 Contact – 60 Contact – 50 Contact (High Current) – 80 Contact (High Current) UPPER AXIS USAGE SR402 These options support unrestricted (continuous) rotation of positioner axes. They can be ordered in two conﬁgurations: integrated wiring for upper positioner axes and/or point-to-point thru-paths for customer use.
PAGE 3
thru-hole options TH002 These options provide a protective housing through the center of selected positioner models. They are available in either indoor or outdoor conﬁgurations. Applications for this option include cable pathways and stationary ﬁxtures which pass through the center of the axis. Electrical travel limits typically remain enabled when this option is purchased. Consult your local sales representative when conﬁguring this option.
PAGE 4
mounting thread options These options are available for applications requiring localized conﬁgurations. • MM002 - Metric Threads in Mounting Hole Interface > M6-1 – Replaces 1/4–20 UNC > M10-1.5 – Replaces 3/8-16 UNC > M12-1.75 – Replaces ½-11 UNC > M16-2 – Replaces 5/8-11 UNC > M20-2.5 – Replaces ¾-10UNC • MM003 – Third Party Mounting Hole Interface Replication - Consult your local sales representative with speciﬁc bolt circle and thread requirements. *Thread depth is 1.25 to 1.
PAGE 5
wedge options WG002 Wedge options can be special-ordered for applications in which the conﬁguration requires the positioner to be pre-tilted. Applications include downward tilt of Roll/ EL positioners in which the wedge’s resulting tilt shifts the elevation travel beyond its normal downward-look angle. Wedges are constructed of the same material, steel or aluminum, as the positioner or base-riser and in a way that does not limit the positioner assembly’s total capacity and overall speciﬁcations.