Users Manual 57946-50 rA
Welcome to B-hyve™ Connecting with B-hyve™ Thank you for purchasing the Orbit® B-hyve™ wifi sprinkler timer. At Orbit, we share your passion for a beautiful landscape while protecting our most valuable resource– water. For over 40 years, this passion has driven us to deliver top of the line irrigation products to millions of customers all around the world.
Table of Contents Contents in the Box . . . . . . . . . . . . . . . . . . . . . . . 4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Timer Installation . . . . . . . . . . . . . . . . . . . . . . . . . 6 Uninstalling/Reinstalling . . . . . . . . . . . . . . . . . . . 8 The B-hyve App . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Timer Controls/Features . . . . . . . . . . . . . . . . . 10 Simple Controls . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents in the Box A Wifi Sprinkler Timer D Keys B Screwdriver E Quick Start Guide C Installation Hardware A 4 B C D E
Getting Started Your B-hyve™ sprinkler timer is great for new installations or for replacing an old sprinkler timer. Here are some basic steps to get your timer set up and get you closer to saving water and money. Install the timer Choose a location on your property with a good wifi signal. Install the B-hyve™ app on your smart device You will need a smart device to connect the timer to wifi. After the timer is paired, you can also use a computer to adjust your timer.
Timer Installation Select a location Choose a location near power and away from direct sunlight, if possible. Make sure to leave room for the timer door to open completely. Keyhole 1/8" No. 8 Screw Mount the timer Install a screw (included) into the wall. Use the expanding anchors (included) for plaster, masonry or drywall installations. Hang the timer on the installed screw using the keyhole slot. Level the timer and use the second screw in one of the preformed mounting holes to secure the timer.
Timer Installation–Connecting to WIFI Plug in your Orbit® B-hyve™ timer Once your Orbit® timer is plugged into the power source, it will automatically look to pair with your smart device. In the top left corner of the timer screen the “wifi” icon will begin a graduated blinking sequence. This indicates that your timer is ready to pair with a smart device.
Uninstalling/Reinstalling How to re-pair with wifi You can re-pair your smart device with your B-hyve™ timer by turning the dial to “Off” and pressing the reset button on the back of the swing panel. The timer display will show “Pair.” Deleting the timer from the app You may need to the delete the timer from a smart device. Go to settings to deauthorize the timer, after which it will ask for confirmation to remove the timer.
The B-hyve™ App Timer Connected Symbol Weather/Temp. Running Status/Messaging Stop Watering Rain Delay Next Zone Calendar Programs Settings Zone List Remote Control or Home Button Note: There is a wizard in the app to guide you through initial set up of your sprinkler timer. In addition, there are help icons throughout the app with more information and useful tips.
Timer Controls/Features Your timer was built to make installation easy and fast, while providing convenient controls to make adjustments from anywhere in the world, or when you’re standing in front of the timer.
Simple Controls Programming at the timer can be done whether you are connected to wifi or not. It allows the gardener who left their phone inside to run a manual cycle, or adjust programming as needed and keep dirty hands away from the phone.
Using the DIAL The DIAL can be used to scroll up or down, left or right on menus, dates and times. Press the DIAL to confirm a selection, to deselect or to skip a running station.
Using the BACK and CLEAR Buttons The BACK button can be used return to the main menu, or can be pushed twice to return to auto. The CLEAR button can be used to clear entries in a selected screen. The CLEAR button may also be used to cancel Rain Delay, cancel a running program or cancel a manual watering cycle.
Using the PROGRAM (PROG ABC) Button The A, B, C and Smart programs provide the flexibility to set up and run different programs for plants with different watering needs. For example: you could set your lawn zones to run on program A, your flowerbeds to run on program B and your garden to run on program C. Or, you can set up your zones to use smart watering and the timer will use local weather and on-site information to automatically set a watering schedule for you.
Using the RAIN DELAY Button The RAIN DELAY button can be used to turn off all watering for a duration of 1 to 32 days. Press RAIN DELAY repeatedly, or turn the dial after pressing rain delay once, until the desired number of days is showing in the LCD. To cancel a rain delay, press CLEAR.
Timer LCD Status Bar Function WIFI Solid–shows signal strength of wifi and indicates that it is connected. Graduated Blinking–indicates the timer is in pairing mode. Blinking–it is not connected to wifi. Solid, with an exclamation point– communicating with wifi, but not communicating with Orbit’s servers.
Programming the Timer–AUTO and OFF The timer should be in AUTO during the irrigation season and OFF in the winter months or the non-irrigation months. Turn the dial to the AUTO position and press the dial or just leave it there to keep it in AUTO. If the dial selection is left in any position other than OFF, it will revert back to AUTO after approximately 20 seconds. To turn your timer OFF, turn the dial to OFF and press the dial or just leave it in the OFF position.
Programming the Timer–DATE/TIME If you are connected to wifi, the time and date will automatically be sent to the sprinkler timer. To set the date and time manually, turn the dial until the selection box is on DATE/ TIME and press the dial. Set the date by turning the dial until the correct year, month and day are shown and press the dial to confirm each selection. When setting the time, press the dial when the right time is set. Be careful to make sure that the am/pm selection is correct.
Programming the Timer–START TIME This is the time that the first zone will begin watering. Only one start time is needed to run each station in the program. Turn the dial until the selection box is on START TIME and press the dial. Turn the dial to the desired start hour and press the dial to confirm the selection. Turn the dial to the desired start minute and press the dial to confirm the selection. Note: only one start time is needed to run all of your zones and that start time will show up as 1st.
Programming the Timer–RUN TIME This is where you will set up how long each zone will run Turn the dial until the selection box is on RUN TIME and press the dial. The station number will flash–turn the dial until the desired zone is flashing and press the dial. The duration for that zone will flash–turn the dial until the desired duration is showing and press the dial. Repeat this process for each zone you wish to set up.
Programming the Timer–HOW OFTEN This will determine HOW OFTEN (what days or interval) the timer will water. Turn the dial until the selection box is on HOW OFTEN and press the dial. Rotate the dial until the desired day of the week or Odd/Even or Int is flashing and press the dial. If days of the week are chosen, repeat this process until all of the desired watering days have a box around them. If INT (interval) is chosen, rotate the dial until the desired number of days between waterings is showing.
Programming the Timer–BUDGET Budget makes it easy to change all of your run times without having to change them one by one. Turn the dial until the selection box is on BUDGET and press the dial. Adjusting budget will adjust all of the run times in a program by the percentage chosen. Example: If you have zones set up to water for 10 minutes and you adjust your budget from 100% to 150%, those same zones will water for 15 minutes without having to change each run time.
Manual Operation Manual is used to test zones or run an extra cycle for a zone, a program or for all zones. Turn the dial until the selection box is on MANUAL and press the dial. Note: you can program more than one specific zone using this process. Repeat the steps for zone selection and duration to water additional zones. ALL will be displayed in the LCD. To water all zones– • Press the dial while ALL is displayed and it will ask for a duration. • Rotate the dial to the desired duration.
Remember, you can set your timer up with the app. But, if you don’t have wifi or just want to make an adjustment while you are outside, you can do it at the timer. Timer changes will be reflected in the app, and app changes will be reflected at the timer. For more detailed instructions or troubleshooting information, visit bhyve.orbitonline.com Also, the app has help screens and video to assist you with wifi connections, programming, smart watering and other general questions you may have.
