WS-7013U Wireless 433 MHz Temperature Station Instruction Manual Register your product on the web at: WWW.ORECK.
TABLE OF CONTENTS Topic Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Selecting Units of Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Mounting Troubleshooting Maintenance and Care Specifications Warranty Information 1 Page 2 3-5 5-7 7-8 8 9 9 9-10 10-12 12 13-14 14
INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket (Figure 2) 3. (3) 1/2" Philips screws 4. One strip of double sided adhesive tape 5. Instruction Manual and Warranty Card 6. (2) AAA 1.5V batteries 7. (2) AAA 1.5V batteries Figure 1 Figure 2 ADDITIONAL EQUIPMENT 1.
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
Any walls the signal will have to pass through will reduce distance. An outdoor wall or window will have 20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus resistance should not exceed 80 feet in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor, but direct rain must be avoided. To complete the setup of your indoor temperature station after the 10 minutes have passed, please follow the steps below: 1.
3. The hour will now be flashing. a. Press and release the "MIN/MAX" button until the correct hour is shown. Note: When in the 12h mode "PM" is displayed under the word "TIME" during PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the "SET" button once. 4. The minutes will now be flashing. a. Press and release the "MIN/MAX" button until the correct minutes are displayed. Press and release the SET button once more to complete the setup.
B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. Battery Cover 1. Remove the battery cover on the backside. To do this, push the cover upward and pull it out. 2. Observing the correct polarity, install (2) AAA batteries. 3. Replace the battery cover. 4. Wait 10 minutes or until both the indoor and outdoor temperatures are shown on the indoor temperature station.
5. The indoor temperature station should now show: "-:- -" in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s. II. TIME A. SETTING THE TIME 1. Press and hold the "SET" button for 5 seconds, "12h" will appear in the TIME LCD. 2. Press and release the "MIN/MAX" button to select either 12h time (am/pm) or 24h time. 3. Press and release the "SET" button 2 times, the hour will flash in the upper left corner.
4. Press and release the "MIN/MAX" button to set the hour. 5. Press and release the "SET" button to move to the minute setting. 6. Press and release the "MIN/MAX" button to set the minutes. 7. Press and release the "SET" button to activate the clock. Note: When in 12h mode, there is only a "PM" display, which appears under "TIME." If there is no display, then it is in AM mode. Make sure you set the time accordingly. III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREMENT 1.
IV. FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the "MIN/MAX" button. "MIN" appears in the temperature LCDs and the recorded minimum temperatures are displayed. 2. Press and release the "MIN/MAX" button to toggle to the maximum temperatures. The time of occurrence of the value for outdoor temperature will also flash. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES 1. To reset both the minimum and maximum temperatures—press and hold the "RESET/+" button for 4 seconds. V.
before permanently mounting. A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor. 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. THE TEMPERATURE STATION 1. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. 2.
Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Make sure all batteries are new. 4) Place remote temperature sensor and indoor temperature station in position so the straight-line signal is not passing through more than two or three walls.
responsive to ambient air currents because of the shielding effect of the display case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). In addition, the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range. Error is usually greater at the extreme ends of a range, making it harder to compare different ranges with different curves.
SPECIFICATIONS Transmitting 433MHz Frequency Measuring Temperatures Indoor Temperature 32°F to 156.2°F with Station: Indoor 0.2°F resolution. (0°C to 69.0°C with 0.1°C resolution) Remote Temperature -21.8 °F to 156.2°F Sensor: Outdoor 0.2°F resolution. (-29.9°C to 69.0°C with 0.1°C resolution) Temp accuracy +/- 1°F (+/- .
Remote Temperature Sensor Battery life 1.57" x 0.9" x 5.04" (40 x 23 x 128 mm) Approximately 1 year WARRANTY INFORMATION Oreck Corporation warrants the Indoor/Outdoor Clock and Weather Station (WS-7013U) free from defects in material and workmanship under normal, non-commercial use and service. Oreck will remedy any such defects if they appear within one (1) year from date of purchase. This warranty gives you specific legal rights, and you may have other rights, which vary, from state to state.
©2002 Oreck Holdings, LLC. All rights reserved.