GB DIGITAL WEATHER FORECASTER WITH REMOTE THERMO-HYGRO SENSOR AND RADIO CONTROLLED CLOCK MAIN FEATURES: MAIN UNIT I A A1 MODEL NO.: BAR182HG USERS MANUAL D B E C INTRODUCTION F G Congratulations on your purchase of the Weather forecaster with cable free sensor and radio-controlled calendar clock (BAR182HG).
GB A . FRONT DISPLAY A four line easy-to-read LCD K. [ ] BUTTON Decreases the value of a setting A1. WEATHER FORECAST WINDOW Graphically illustrates a weather forecast L. [ I ] BUTTON Advances the value of a setting B. [ ] BATTERY-LOW INDICATOR Activates when the remote-sensor or main unit battery power is low C. [ TEMP. % RH ALARM : M. [ ON / OFF ] BUTTON ( TEMP/% RH ALARM ) Enables / disables HI/LO temp alarm and HI/LO % RH alarm ] RADIO-RECEPTION SIGNAL N.
GB FEATURES: REMOTE THERMO-HYGRO SENSOR A. TWO-LINE LCD Displays the current temperature and humidity monitored by the remote unit B. LED INDICATOR Flashes when the remote unit transmits a reading C. °C/°F SLIDE SWITCH Selects between Centigrade (°C) and Fahrenheit (°F) D. CHANNEL SLIDE SWITCH Designates the remote unit Channel 1, Channel 2 or Channel 3 E. RESET Returns all settings to default values F. BATTERY COMPARTMENT Accommodates two UM-4 or AAA-size batteries G. BATTERY DOOR H.
GB easier synchronization between the transmission and reception of signals. BATTERY AND CHANNEL INSTALLATION: REMOTE UNIT 4. Position the remote unit and main unit within effective transmission range, which, in usual circumstances, is up to 30 meters. The remote thermo-hygro sensor unit uses two (2) UM-4 or AAA size alkaline batteries. Note that the effective range is vastly affected by the building materials and where the main and remote units are positioned. Try various set-ups for best result.
GB Remote unit Wall-mount LOW BATTERY WARNING Table Stand When it is time to replace batteries, the respective low-battery indicator will show up when the respective channel is selected. HOW TO USE THE TABLE STAND OR WALL MOUNTING The main unit has a removable table stand, which when connected, can support the unit on a flat surface. Or you can remove the stand and mount the unit on a wall using the recessed screw hole. As for the remote unit, it comes with a wall-mount holder and a removable stand.
GB If no signals are received, blanks --- will be displayed and the kinetic wave icon will not show. To display temperature / humidity readings from a remote sensor: To force a signal search: Press [CHANNEL] until the appropriate remote sensor channel is displayed in the box under the kinetic-wave. Press and hold [CHANNEL] & [MEM] for 2-seconds to enforce a 3-minute search. This is useful in synchronizing the transmission and reception of the remote and main units.
GB HOW TO READ THE KINETIC WAVE DISPLAY THE COMFORT-LEVEL ICONS The comfort level indicators COM, WET or DRY will tell you if the current environment is comfortable, too wet or too dry. The kinetic wave display shows the signal receiving status of the main unit. There are three possible forms: The comfort indicator will appear on the display when the following conditions are satisfied: The unit is in searching mode. Indicator displays on the unit Transmission data are securely registered.
GB TEMPERATURE, HUMIDITY & PRESSURE TREND INDICATORS MAXIMUM AND MINIMUM TEMPERATURE AND HUMIDITY The temperature-trend, humidity-trend and pressure trend indicators show the trends of collected readings. Arrows indicate a rising, steady or falling trend. The maximum and minimum recorded temperature and humidity readings will automatically be stored in the memory. To display the maximum and minimum display memory: 1. Select the channel to be checked.
GB The respective HI, LO or both indicators will light up to signify the status of the alarm.
GB MODE 3. Hour-Minute-Day of the Week (of local time) Indicator displays on the unit Forecast Hour-Minute (of alternate time zone) Sunny Slightly Cloudy Cloudy Rainy MODE 4. Hour-Minute-Day of the Week (of second time zone) NOTE: Day-Month (of alternate time zone) 1. The accuracy of a general pressure-based weather forecast is about 70% to 75%. 2. The weather forecasts from this unit are predictions that cover the next 12 to 24 hours. It may not necessarily reflect the current situation.
GB Press [ MODE ] to confirm. The minute digits will blink. Repeat the same procedure to set the minutes, hour, current day, month, display language, weekday and hour offset for the 2nd time zone. - Strong Note: The time and date are displayed in 24-HOUR clock format. For the language display, you can choose among English (E), German (D), French (F) and Italian (I). Weekday is in the usual sequence of Monday through Sunday.
GB 5. Enter the minutes using [ ] and [ ](CLOCK). NOTE ON °C AND °F ] icon for the alarm 6. Press [ ALARM ] to exit. The [ chosen will be displayed indicating the alarm set above is now armed. You can also arm or disarm an alarm by pressing the [ (CLOCK) button. The temperature display designation of °C or °F on the main display unit will override the display selection made on the remote sensor.
GB SPECIFICATIONS Temperature Measurement Main unit Indoor Temperature measurement Proposed operating range : NOTE ON COMPLIANCE Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. -5.0°C to +50.0°C (23.0°F to 122.
GB COUNTRIES RTTE APPROVAL COMPLIED: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Italy, Luxembourg, Netherlands, Portugal, Spain, Sweden, UK and Ireland.
