Owner's Manual

ManualsBrandsOregon Scientific ManualsDetectorsOregon Scientific BAR608HGA

Wireless Weather Station

Model : BAR608HGA

User Manual

BAR608HGA lab test cover R2 1/8/04, 6:38 PM1

Summary of content (18 pages)

PAGE 1
Wireless Weather Station Model : BAR608HGA User Manual BAR608HGA lab test cover R2 1 1/8/04, 6:38 PM
PAGE 2
Barometer ............................................................... 10 Contents ................................................................... 1 Barometric Trend ................................................. 10 Introduction .............................................................. 2 Set Unit and Altitude ............................................ 10 About Oregon Scientific .......................................... 2 Weather Forecast ..............................................
PAGE 3
EN INTRODUCTION ABOUT OREGON SCIENTIFIC Thank you for selecting the Oregon ScientificTM Wireless Weather Station (BAR608HGA). This device bundles precise time keeping, weather forecast, barometric trend with altitude adjustment, and indoor and outdoor temperature and humidity monitoring features into a single tool you can use from the convenience of your home. Visit our website (www.oregonscientific.
PAGE 4
EN PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT button 2. Weather Forecast & Barometric Trend Area 3. Outdoor Temperature & Humidity Area 4. Indoor Temperature & Humidity Area 5. Clock / Alarm Area 6 Moon Phase 7. and : increase or decrease setting / activate or deactivate Atomic Clock. 8. RESET hole 9. ((.)): view alarm status; set alarm 10. MEMORY: view current, maximum and minimum temperature / humidity readings 11. CHANNEL: switch remote sensor 12.
PAGE 5
EN BACK VIEW 1. 1 Wall mount 2. Battery compartment 3.
PAGE 6
EN REMOTE SENSOR (THGR122NX) 1 1 2 2 3 4 1. Wall mount hole 1. LCD display 2. RESET 2. LED Status indicator 3. Channel number (1 - 3) 4.
PAGE 7
EN CHANGE SETTINGS GETTING STARTED BATTERIES Batteries are not supplied with this product. You will need to purchase 3 x UM-3 (AA) 1.5V alkaline batteries for the main unit, and 2 x UM-4 (AAA) 1.5V alkaline batteries for the remote sensor. 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. TABLE STAND OR WALL MOUNT Use the stand on the back of the product, or mount it on a wall with a nail.
PAGE 8
EN For best results: SETUP SENSOR 1. Open the remote sensor battery compartment with a small Phillips screwdriver. • Insert the batteries and select the channel before you mount the sensor. 2. Insert the batteries, matching the polarity as shown in the battery compartment. • Place the sensor out of direct sunlight and moisture. • Do not place the sensor more than 30 meters (98 feet) from the main (indoor) unit. SWITCH OPTION Channel Channel 1 - 3.
PAGE 9
EN DATA TRANSMISSION CLOCK Data is sent from the sensor(s) every 40 seconds. The reception icon shown in the Temperature and Humidity Areas show the status. ICON --- shows in Outdoor Temp / Humidity Area This product shows the current time, and day of week in English, French, German, Italian, or Spanish. The US Atomic Clock in Boulder, Colorado automatically updates this information unless you disable the feature.
PAGE 10
EN TURN ATOMIC CLOCK ON/OFF ALARMS Perform this step if you cannot receive Atomic Clock signals. Press and hold DOWN for 2 seconds. Then, manually set the clock following the "Set Clock" instructions (below). This product is equipped with a 2-minute crescendo alarm. VIEW ALARM SETTINGS The signal icon indicates that the Atomic Clock feature is ON. No icon means that it is OFF Press ((.)). The Alarm Time and ((.)) status will show in the Clock Area.
PAGE 11
EN If no button is pressed, the Alarm will automatically silence after 2 minutes. It will then sound again after 8 minutes. SET UNIT AND ALTITUDE BAROMETER 1. Press PRESSURE to select the unit of measurement: mb / hPa or inHg. 2. Press and hold PRESSURE for 2 seconds. 3. Select the altitude (-328 feet to 8203 feet in increments of approximately 33). Press UP or DOWN to change the setting. Press PRESSURE to confirm. You can set the unit of measurement (mb/hPa or inHg) and altitude.
PAGE 12
This product can display current, minimum, and maximum temperatures and humidity percentage information collected by the remote sensors and main (indoor) unit. MINIMUM / MAXIMUM RECORDS Press MEM to toggle between current, maximum (MAX) and minimum (MIN) records. To clear the records, press and hold MEM for 2 seconds. A beep will sound to confirm that the memory has been cleared. Outdoor data is collected and displayed every 40 seconds. Indoor data is collected and displayed every 10 seconds.
PAGE 13
EN Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product. The technical specification of this product and contents of this user guide are subject to change without notice. Images not drawn to scale. NOTE When you press RESET, all settings will return to default value, and you will lose all stored information. SAFETY AND CARE Clean the product with a slightly damp cloth and alcoholfree, mild detergent.
PAGE 14
EN Problem Symptom Remedy SPECIFICATIONS Remote sensor Cannot change channel Check sensors. Only one sensor is working ( 7) MAIN UNIT DIMENSIONS LxWxH 142 x 63 x 158 mm (5.5 x 2.5 x 6.2 inches) Data does not match main unit Initiate a manual sensor search ( 8) Weight 366 g (12.96 ounces) with battery REMOTE SENSOR DIMENSIONS LxWxH 92 x 60 x 20 mm (3.6 x 2.4 x .79 inches) Weight 63 grams (2.
PAGE 15
EN RELATIVE HUMIDITY CLOCK Range 25% to 95% Atomic Clock Auto or manual (disabled) Resolution 1% Clock display HH:MM:SS Memory Minimum / maximum Hour format 12hr AM/PM Time zone PA (Pacific), MO (Mountain), CE (Central) or EA (Eastern) Calendar MM/DD; weekday in 5 languages (E, D, F, I, S) Alarm Single alarm with 2- minute crescendo and 8-minute Snooze BAROMETER Unit mb/hPa or inHg Range 700 to 1050 mb (20.67 to 30.01 inHg) Resolution 1 mb (0.
PAGE 16
• Increase the separation between the equipment and receiver. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
PAGE 17
EN is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: DECLARATION OF CONFORMITY The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com, or on the warranty card for this product) for all inquiries instead. We Name: Oregon Scientific, Inc. Address: 19861 SW 95th Place, Tualatin, Oregon 97062 USA Telephone No.: 1-800-853-8883 Fax No.