EN Weather forecast ................................................. 13 TABLE OF CONTENTS Temperature ........................................................ 14 About this guide ................................................... 2 Backlight .............................................................. 16 Product overview .................................................. 3 Projector .............................................................. 16 Getting started .................................
EN In this box, you will find: ABOUT THIS GUIDE Congratulations on your selection of the Oregon Scientific Maranello Radio-Controlled Projection Clock with Indoor and Outdoor Temperature (FSP-301). This powerful device bundles time keeping, alarm, projection, indoor and wireless outdoor temperature measurement features. Keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know.
EN DESCRIPTIONS PRODUCT OVERVIEW 1. TOP VIEW 1 2 3 4 3 Snooze / Light ( 13, 16) 2. Channel ( 9, 14) 3. Memory ( 14) 4.
EN LCD DISPLAY DESCRIPTIONS 1. 1 2 Low Battery icon( 8) 6 2. Weather Forecast ( 13) 7 3. RF Reception Signal ( 10) 8 4. Clock ( 10) 5. Date / Alarm / Alarm Type ( 10-12) 6. Remote Sensor ( 9, 14) 7. Temperature Trend ( 16) 8.
EN FRONT VIEW BUTTON DESCRIPTIONS 1 2 3 4 5 1. Clock – set time / date or view seconds / day of week ( 9, 11) 2. Up / Down – increase / decrease setting or activate / deactivate auto-synchronization ( 9, 11) 3. Alarm – set / activate / deactivate alarm( 12) 4.
EN BACK VIEW DESCRIPTIONS 1. 1 2 3 4 5 Projector focus knob ( 17) 2. 180˚ rotation (flip image) button ( 17) 3. Image rotation button ( 17) 4. ˚C/ ˚F switch ( 9, 15) 5. Projector switch ( 17) 6. Radio signal format switch ( 10) 7. Reset button ( 18) 6 7 NOTE AC power adapter and battery compartment not shown.
EN REMOTE UNIT DESCRIPTIONS 1. 1 2 3 4 5 6 7 8 7 Temperature ( 14) 2. LED indicator ( 10, 15) 3. Channel number ( 9, 14) 4. ˚C/˚F switch ( 9, 15) 5. Reset button ( 18) 6. Channel switch ( 9, 14) 7. Batteries ( 8) 8.
EN NOTE Insert the batteries in the remote unit before you set up the main unit. Do not use rechargeable batteries. GETTING STARTED BATTERIES Batteries for the remote and main units are supplied with this product. Replace them whenever the low battery signal ( ) displays. The battery door is located on the bottom of the main unit. Use a small Phillips screwdriver to remove the remote unit compartment lid. Be sure to match the correct polarity, as shown in the battery compartment.
EN CHANGE SETTINGS Press and hold CLOCK or ALARM for 2 seconds to enter setting mode. Then, press UP or DOWN to change each setting. Press and hold to enter fastsetting mode. Press CLOCK or ALARM to switch between settings. NOTE Additional remote units sold separately. If you are using more than one remote unit, be sure to select a different channel number for each unit. INSTALLATION Mount the remote unit on a flat surface using the recess hole on the back of the unit.
EN · · Do not place the remote unit more than 20 – 30 meters (60 – 90 feet) from the main (indoor) unit. CLOCK This product can automatically synchronize the date and time with official time-keeping organizations in Frankfurt (Germany) and Rugby (England). When the unit is within 1500 km (932 miles) of a RF signal, the reception icon will blink during reception. Position the unit so that it faces the main (indoor) unit. Minimize obstructions such as doors, walls, and furniture.
EN Strong signal Weak signal TO DISABLE OR ENABLE AUTOSYNCHRONIZATION Press DOWN for 2 seconds to disable the autosynchronization. The unit will not respond to radio signals until you reactivate the synchronization. No signal To enable auto-reception, press NOTE For best results, place the unit away from metal or electrical objects, and near a window with a clear view to the sky. UP for 2 seconds. SET OR CHANGE THE CLOCK Clock auto-synchronization must be deactivated before you manually set the clock.
EN 1. 2. Press and hold CLOCK for 2 seconds to enter setting mode. ALARM When activated, the Beep Alarm starts quietly, then gradually becomes louder until it crescendos at 1 minute. It shuts off at two minutes. The LCD display lights up for the first 5 seconds. Select the 12/24-hour format, hour, minute, year, date/month format, month, date, and display language. Press UP or DOWN to change the setting. Press CLOCK to confirm.
EN 3. Press ALARM to confirm. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather within a 30 to 50 km (19 - 31 mile) radius with 70 to 75 percent accuracy. The weather forecast is always displayed. SNOOZE Press SNOOZE/LIGHT to temporarily disable the alarm for 8 minutes. The alarm icon will blink while Snooze is activated. Clear TO TURN THE ALARM OFF OR ON Press CLOCK, UP or DOWN.
EN SELECT REMOTE UNIT CHANNEL Press CHANNEL to switch between CHANNEL 1, 2, 3, or indoor. Or, press and hold for 2 seconds to enter auto scan mode. If you select “Auto”, the channel will change every 3 seconds. Press CHANNEL or MEMORY again to deactivate this auto function. TEMPERATURE With the press of a button, you can check the current indoor or outdoor temperature, trend, and record measurements. Outdoor measurements are collected by the remote unit. VIEW MIN / MAX / CURRENT MEASUREMENTS Press MEMORY.
EN Searching Strong signal NOTE Check the remote unit batteries if no signal is No signal found. SET UNIT The ˚C / ˚F switch is located on the back of the main unit, and in the battery compartment for the remote unit. Select ˚C or ˚F. NOTE Signals from household electrical appliances such as doorbells and home security systems can cause temporary reception failures between the indoor and outdoor units. This is normal and does not affect the general performance of the product.
EN TRENDS The temperature trend arrow for the last 30 minutes always displays. Trend BACKLIGHT Press SNOOZE/LIGHT to illuminate the backlight for 5 seconds. Temperature PROJECTOR + 0.5 ˚C This product has a built-in projector for viewing the time. Steady - 0.5 ˚C NOTE The maximum projection range is 2 meters (6 feet). The image gets larger the farther you display it.
EN PROJECT THE TIME In a darkened room, press SNOOZE/LIGHT to display the time for 5 seconds. FOCUS IMAGE The FOCUS knob is located on the back of the unit. Rotate to adjust. MOVE IMAGE Adjust the projector arm. CONTINUOUS PROJECTION The AC power adapter must be plugged in to use this feature ( 8). Slide the PROJECTOR switch located on the back of the product to the ON position. FLIP IMAGE Press the 180˚ Rotation button while the projector is on.
EN RESET SYSTEM SAFETY AND CARE The RESET buttons are located on the back of the main unit, and in the battery compartment for the remote unit. Press these buttons with the tip of a blunt object (such as a ball point pen) whenever you change the batteries, or whenever performance is not behaving as expected (e.g., unable to establish radio frequency link with remote unit or automatic clock).
EN · Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. · The contents of this user guide are subject to change without notice. · Do not tamper with the internal components. · Images not drawn to scale. Colors may vary. · Do not mix new and old batteries or batteries of different types. Do not use rechargeable batteries with this product. · · Remove the batteries if storing this product for a long period of time. · · Do not scratch the LCD display.
EN Problem Symptom Cannot auto-synch 1. 2. 3. Remedy Adjust batteries. Press RESET ( 18). Manually activate auto-synch ( 11). If it still fails, you may be too far from a signal. 20 Problem Remote unit Cannot locate Temp Shows “LLL” or “HHH” Symptom Remedy Check batteries ( 8) Check location ( 9) Temperature is out of range.
EN Outdoor Range SPECIFICATIONS Main unit dimensions LxWxH 174 x 103 x 36 mm (6.85 x 4.06 x 1.42 inches) Weight 388 grams (0.86 lbs) (with batteries) Resolution Memory Trend Radio-controlled clock Synchronization Auto or disabled Clock display HH:MM:SS Hour format 12hr AM/PM (MSF format) 24hr (DCF format) Calendar DD/MM or MM/DD userselectable; weekday selection in 5 languages (E, D, F, I, S) Remote unit dimensions LxWxH 92 x 60 x 20 mm (3.6 x 2.4 x 0.8 inches) Weight 100 grams (0.2 lb.
EN Alarm Snooze Remote unit RF frequency Range Transmission Channel No. Unit Power Main unit Ferrari Engine or Beep; 2 minute crescendo for Beep 8 minutes Remote unit 433 MHz 30 meters (98 feet) with no obstructions every 40 seconds 1, 2, or 3 ˚C or ˚F AC/DC 6V power adapter (for continuous projector) 2 x UM-4 (AAA) 1.5V alkaline batteries ADDITIONAL RESOURCES Visit our website (www.oregonscientific.
EN C-DECLARATION OF CONFORMITY Additional information: This product contains the approved transmitter module TX 01 and complies with the essential requirements of Article 3 of the R&TTE 1999/5/EC Directives, if used for its intended use and that the following standard(s) has/have been applied: The product is therefore conform with the Low Voltage Directive 73/23/EC, the EMC Directive 89/336/EC and R&TTE Directive 1999/5/EC (appendix II) and carries the respective CE marking.
EN Radio-Controlled Projection Clock with Indoor and Outdoor Temperature (Model #: FSP-301 Maranello) User Manual 24
