EN Full Weather Station with Radio Controlled Clock and Projection (Model #:PS L02A) User Manual PS-L02A English Cover r8 op 1 Black 2/13/04, 10:45 AM
EN Projector ................................................................. 18 Reset system ........................................................... 19 Safety and care ....................................................... 20 Warnings ................................................................. 20 Troubleshooting ....................................................... 21 Specifications .......................................................... 22 About Oregon Scientific ........................
EN In this box, you will find: ABOUT THIS GUIDE Congratulations on your selection of the Philippe Starck with Oregon Scientific Full Weather Station with Radio Controlled Clock and Projection (PS L02A). This innovative time piece provides not only time keeping, but also alarm clock, indoor and wireless outdoor temperature, humidity monitoring, weather forecast, and projection clock features into one convenient package.
EN PRODUCT OVERVIEW DESCRIPTIONS TOP VIEW 1. 2. 3.
EN LCD DISPLAY DESCRIPTIONS 1. 2. 3. 4. 5. 6. 7. 8.
EN BACK VIEW BUTTON DESCRIPTIONS 1. 2. 3. 4. 5. 6. 7.
EN BOTTOM VIEW DESCRIPTIONS 1. 2. 3. 4. 5. 1 2 3 Battery compartment Light sensitivity knob Reset button Backlight switch DC power input jack 4 5 NOTE AC power adapter not shown.
EN REMOTE UNIT DESCRIPTIONS 1 1. 2. 3. 4. 5. 6. 7. 8. 9.
EN GETTING STARTED NOTE Insert the batteries in the remote unit before you set up the main unit. Do not use rechargeable batteries. BATTERIES Batteries for the remote and main units are supplied with this product. Replace them whenever the low battery signal ( ) displays. Remove the battery compartment lid on the bottom of the main unit, and insert the batteries. Use a small Phillips screwdriver to remove the remote unit compartment lid.
EN SWITCH BETWEEN MODES Press SELECT. The select mode will flash. The display will stop flashing if no key is pressed within 5 seconds. NOTE Additional remote units sold separately. If you are using more than one remote unit, be sure to select a different channel number for each unit. CHANGE SETTINGS Press and hold SELECT for 2 seconds. Then, press UP or DOWN to change each setting. Press SELECT to switch options.
EN • Position the unit so that it faces the main (indoor) unit. Minimize obstructions such as doors, walls, and furniture. RECEPTION Reception takes 2 – 10 minutes to complete. Once complete, the icon will stop blinking. You may need to experiment with various locations to get the best reception. Strong signal CLOCK This product can automatically synchronize the date and time with the US Atomic Clock. When the unit is within 932 miles (1500 km) of a RF signal, the reception icon will blink.
EN TO DISABLE OR ENABLE AUTOSYNCHRONIZATION In Clock mode, press DOWN for 2 seconds to disable the auto-synchronization. The unit will not respond to radio signals until you reactivate the synchronization. ALARM When activated, the Melody Alarm starts quietly, then gradually becomes louder. It shuts off after two minutes. The LCD display lights up for the first 8 seconds. SET ALARM To enable auto-reception, press UP for 2 seconds. 1. SET OR CHANGE THE CLOCK 1. 2. 3. 2.
EN 1. SNOOZE Press the SNOOZE/LIGHT button the top of the unit to temporarily disable the alarm for 8 minutes. The alarm icon will blink while Snooze is activated. 2. 3. TO TURN THE ALARM OFF OR ON Press any button to stop the alarm. To turn the alarm off completely (deactivate it for the next day), press ALARM. Press SELECT several times until the calendar area flashes. Press and hold SELECT for 2 seconds to enter the calendar setting mode. Select the year, month, date, and language.
EN BAROMETER This product tracks barometric pressure changes over the past 24 hours to provide the weather forecast (→ pg.14) and a trend line showing the direction of barometric change. Barometric changes are measured by the main (indoor) unit. Trend BAROMETRIC TREND The barometric trend arrow for the last 30 minutes is always displayed.
EN SET UNIT AND ALTITUDE You can set the unit of measurement (mb/hPa or inHg) and altitude. Setting the altitude allows the product to take more accurate barometric measurements. 1. 2. 3. WEATHER FORECAST This product forecasts the next 12 to 24 hours of weather within a 19 - 31 mile (30 to 50 km) radius with 70 to 75 percent accuracy. The weather forecast is always displayed. Press SELECT 2 times until the Barometer Area flashes. Press and hold SELECT for 2 seconds.
EN SELECT REMOTE UNIT CHANNEL While in the Temperature / Humidity Mode, press CHANNEL to switch between CH 1, 2, or 3, or press and hold CHANNEL for 2 seconds to enter Auto scan mode. If only 1 remote unit is in use, you will not be able to change channels or Auto scan. If you select “Auto”, the channel will change every 3 seconds. To deactivate, press and hold CHANNEL for 2 seconds again. Outdoor measurements are collected by the remote unit. Temperature is give at the top; humidity is below.
EN Searching No sensor COMFORT ZONE The indoor and outdoor comfort zones are shown for the following conditions. Sensor found Zone NOTE Signals from household electrical appliances such as doorbells and home security systems can cause temporary reception failures between the indoor and outdoor units. This is normal and does not affect the general performance of the product. Reception will automatically resume once the interference ends.
EN TRENDS The trend arrow for the last 30 minutes always displays. Indoor and outdoor temperature and humidity trends are shown separately. Trend Temperature Relative Humidity +0.9 °F +3% Steady Steady -0.9 °F -3% SET UNIT While in Temperature / Humidity Mode, press SELECT for 2 seconds. Press UP or DOWN to switch between °F and °C. Press SELECT to confirm. BACKLIGHT Press SNOOZE/LIGHT to illuminate the backlight for 5 seconds.
EN 2. 3. Move it to the “AUTO” position to enable continuous backlight controlled by light intensity. When activated, the backlight will be on whenever the unit perceives that the room is dark. The Light Sensitivity knob is located in the battery compartment. Rotate to adjust. PROJECTOR This product has a built-in projector for viewing time and alarm status at night. NOTE The maximum projection range is 2 meters (6 feet). The image gets larger the farther you display it.
EN Press and hold SNOOZE/LIGHT for 2 seconds again to deactivate. ROTATE IMAGE The ROTATION switch is located on the back of the unit. Rotate to adjust. RESET SYSTEM The RESET buttons are located in the battery compartments for the main and remote units. Press these buttons with the tip of a blunt object (such as a ball point pen) whenever you change the batteries, or whenever performance is not behaving as expected (e.g., unable to establish radio frequency link with remote unit or automatic clock, etc.
EN • SAFETY AND CARE Clean the unit with a slightly damp cloth and mild detergent. Avoid dropping the unit or placing it in a location where the AC power adapter will be stepped on. • • • WARNINGS This product is designed to give you years of service if handled properly. Observe the following guidelines: • • NOTE Do not make any unauthorized modifications to this product. Unauthorized modifications will void the warranty. • Never immerse the unit in water.
EN TROUBLESHOOTING Problem Symptom Remedy Temp Shows “LLL” or “HHH” Temperature is out-ofrange. Calendar Strange date / month Change language (→ pg.12) Backlight No continuous backlight Plug in AC power adapter. Check the BACKLIGHT switch. (→ pg.8, 17) Projector No continuous backlight or projection Problem Symptom Remedy Remote unit Cannot locate remote unit Check batteries (→ pg.8) Check location (→ pg.9) Cannot change channel Check sensors. Only one sensor is working (→ pg.
EN Problem Symptom Remedy SPECIFICATIONS 3. Replace batteries. 4. Place clock near window / away from electrical devices, and wait 10 – 20 minutes. Main unit dimensions LxWxH 7.1 x 1.77 x 7.3 inches (181 x 45 x 185.3 mm) Weight 2.02 lbs / 914 grams with battery Remote unit dimensions LxWxH 3 x 1.4 x 3.1 inches (75 x 35 x 78.3mm) Weight 0.3 lbs / 136 grams with battery If it still fails, you may be too far from a signal. Baro Cannot change clock Disable autosynchronization (→ pg.
EN Temperature Unit Range Resolution Comfort Memory Trend Memory Trend °F or °C Main unit: 23 ˚F to 122 ˚F (-5 ˚C to 50 ˚C) Remote Unit: -4 ˚F to 140 ˚F (-20 ˚C to 60 ˚C ) 0.2° F (0.1 °C) 68 °F to 77 °F (20 °C to 25 °C) (see also, Relative humidity) Minimum / maximum +/- 0.9 ˚F (+/- 0.
EN Remote unit RF frequency Range Transmission Channel No.
EN Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ABOUT OREGON SCIENTIFIC Visit our website (www.oregonscientific.com) to learn more about other Oregon ScientificTM products such as digital cameras, projection clocks, health and fitness gear, and weather stations. The website also includes contact information for our customer service department, in case you need to reach us.
EN However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: DECLARATION OF CONFORMITY The information below is not to be used as contact for support or sales.
EN declare that the product Product No.: Product Name: Manufacturer: Address: PS L02A Remote Thermo Hygro IDT Technology Limited Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St., Hung Hom, Kowloon, Hong Kong CAUTION — The content of this manual is subject to change without further notice. — Due to printing limitation, the displays shown in this manual may differ from the actual display. — is in conformity with Part 15 of the FCC Rules.
