AT18_manual_US 10/20/06 14:31 Page 1 ATC-2K
AT18_manual_US 10/20/06 14:31 Page 2 Oregon Scientific ATC-2K Dear customer, Thank you for choosing the Oregon Scientific ATC-2K. Designed and engineered with extreme precision, the Oregon Scientific ATC-2K allows you to record cool action movie footage. We recommend parents help their children with their Oregon Scientific ATC-2K. This manual is designed using technical information to allow you to achieve the best results.
AT18_manual_US 10/20/06 14:31 Page 3 I) Camera Precautions Notice the following guidelines when using your camera. • ATC-2K is not shock-proof. You should avoid dropping it. • For your safety, do not press the buttons on the camera during sports activities. • Do not place the camera in a damp or dusty location for extended periods of time. This may cause a fire or an electrical shock.
AT18_manual_US 10/20/06 14:31 Page 4 Using the camera in cold weather Cold Weather Pouch (Not included) Step 2: Add one extra o-ring for more protection Add one extra o-ring for more protection, follow the same instruction as Step 1 If you want to use your ATC-2K camera in cold weather under 32° F to 14° F (0°C to -10°C), you may order the pouch by completing and mailing the accessories order form found in your ATC-2K box. Note: Step 3: Make sure the cover is closed.
AT18_manual_US 10/20/06 14:31 Page 5 II) Technical Specifications • Sensor resolution 640x480 VGA CMOS sensor • Built-in memory 32MB • SD memory card drive supports cards of up to 2GB (Not included) • Movie storage: 640 x 480 pixels (30 or 15 frames per second) III) Computer System Requirements Minimum System Requirements • Pentium III 800 MHz or higher • Windows XP, Windows 2000 • 128 MB RAM • 800 MB Free hard disk space • SVGA 800 x 600 resolution video support (32 bit) • 16 bit Windows compatible so
AT18_manual_US 10/20/06 14:31 Page 6 IV) Camera Description 1. Lens 2. Camera grip 3. Screw 4. Nut 5. Handlebar grip 6. Helmet grip 7. O-ring 8. USB cable 9. AV cable 10. Rubberized patch 11. Velcro patch 12. Short Velcro strap 13. Long Velcro strap 14. Silicon rubber head strap 15. Bolt 16. Silicon grease container 16 7 9 1 19 18 17 20 15 23 22 5 24 21 25 3 10 4 11 12 6 13 14 7 8 2 17. LCD display 18. ON/OFF & Enter button 19. Movie shutter button 20. Menu button 21. Microphone 22.
AT18_manual_US 10/20/06 14:31 Page 7 Mounting the camera using the velcro strap: V) Camera Mounting Description The camera can be mounted in a number of ways using the straps and the Velcro patch provided. Please follow the methods of mounting as suggested below: Turn it right to unscrew Fixing the position of the camera. a) Turn it left to screw the camera tight to fix it into position. b) Turn it right to unscrew the camera. Mounting the camera onto the helmet using the silicon rubber strap 1.
AT18_manual_US 10/20/06 14:31 Page 8 VI) Quick Start Battery Installation 1. Turn and pull to release the cover at the end of the unit. 2. Release the battery tray by pushing the release hook with a pen or similar object. 3. Insert 2 x AA alkaline batteries into the battery tray with the polarity in the direction as shown. 4. Replace the tray and cover. Be careful!! The edge of the clip is sharp, when turning and pulling the cover, make sure the clip is in the same direction as the lens.
AT18_manual_US 10/20/06 14:31 Page 9 Note: If the camera is connected to your PC, you have to unplug the USB cable to turn off the camera. Inserting/Removing the SD memory Card Make sure the ATC-2K is turned off during the insertion or the removal of the SD card. Warning: The card and the data may be damaged if the SD card is inserted or removed while the camera is on. Insert: 1. Turn off ATC-2K 2. Turn and pull to release the cover at the end of the unit. 3. Insert the card carefully and completely.
AT18_manual_US 10/20/06 14:31 Page 10 VII) Menu Settings 5. The different mode icons are shown in the table below. 1. Press and hold the Menu button for 2 seconds (one beeping sound) to start selecting options. 2. You can shift through different shooting modes by pressing the Menu button repeatedly. The LCD will display each mode as you press the Menu button. 3. Press the Enter button to confirm the selection. (Two beeping sounds) 4.
AT18_manual_US 10/20/06 14:31 Page 11 Resolution a) 640 x 480, 320 x 240, 160 x 120 pixels resolution To change the resolution, press the Menu button until the desired resolution icon is displayed on the LCD. Press the Enter button to confirm your selection. This camera allows you to choose from three video resolutions: 640 x 480, 320 x 240, and 160 x 120 pixels.
AT18_manual_US 10/20/06 14:31 Page 12 Sound Recording When the sound icon is flashing, the “ON” will be shown on screen. “ON” means recording sound during filming. Press the 'Movie shutter button' (one beeping sound) to switch to “OFF” which means no recording sound. After “OFF”, it will loop back to “ON” after pressing "Movie shutter button" again. Press the Enter button (two beeping sounds) to confirm the setting and to go to the next function icon.
AT18_manual_US 10/20/06 14:31 Page 13 Setting the Month When adjusting the month, the “M” will be turned on. Press the 'Movie shutter button' to adjust the month. Press the Enter button to confirm, after which you would be able to adjust the day. Setting the Day When adjusting the day, the “D” will be turned on. Press the 'Movie shutter button' to adjust the day. Press the Enter button to confirm, after which you would be able to adjust the Time.
AT18_manual_US 10/20/06 14:31 Page 14 Available Recording Time The available recording time is an approximation. (These vary depending on the recording conditions and the type of card.
AT18_manual_US 10/20/06 14:31 Page 15 Note: 1. Videos will be saved in AVI format. 2. ATC-2K is connected to the PC when the SD card is inserted in the camera, the '100COACH' folder will show the files on the SD card. ATC-2K Website Please use the link below to check for the latest information. http://www.oregonscientific.com/atc2k/us IX) Playing back video footage on a TV Before contacting an authorized service center at 1-800-853-8883 or sending an email to atc@oregonscientific.com.
AT18_manual_US 10/20/06 14:31 Page 16 I can't capture the video footage -Make sure there is enough space on the internal memory of ATC-2K or the SD card;the display will tell you how much time there is left for video recording. -Make sure the SD card is not locked if you have inserted the SD card. The letters “Err” will be displayed if the SD card is locked. Troubleshooting (continued) The remaining time is not accurate -The remaining time is not always accurate because it is only an estimate.
AT18_manual_US Note 10/20/06 14:31 Page 17
AT18_manual_US 10/20/06 14:31 Page 18 Oregon Scientific, Inc. 19861 SW 95th Avenue Tualatin, OR 97062, USA Hotline: 1-800-853-8883 Website: www.oregonscientific.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.