Music Sphere Wireless Remote Speaker System Model: WRS368 User Manual WRS368 Eng (US) Cover R18 OP 1 7/30/05, 10:51 AM
EN ACCESSORIES IMPORTANT SAFETY INSTRUCTIONS Take care when placing the product on an unstable cart, stand, tripod, bracket or table. Quick stops, excessive force and uneven surfaces may cause the system to overturn and fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket or table recommended by Oregon Scientific, or sold with the product.
EN PROTECTIVE ATTACHMENT PLUG The product is equipped with an attachment plug having overload protection. This is a safety feature. See user manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by Oregon Scientific that has the same overload protection as the original plug.
Stains on the unit should be wiped off with a soft, lint-free cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean. Remember to unplug the unit from the wall outlet before cleaning. • Never use alcohol, solvent, aerosol cleaners, chemical, paint thinner or benzene to clean the unit.
EN FCC Statement ....................................................... 13 Declaration of Conformity .................................... 13 EC-Declaration of Conformity ............................... 13 Music Sphere Wireless Remote Speaker System Model: WRS368 USER MANUAL CONTENTS Important Safety Instructions ................................. 1 Maintenance ............................................................. 2 Contents ...................................................................
TM Thank you for selecting the Oregon Scientific Music Sphere Wireless Remote Speaker System (WRS368) as your personal product of choice. The Wireless Remote Speaker is an ultra-portable unit that lets you listen to audio from almost anywhere in the home or office regardless of where the audio source is located.
EN CONTROL PANEL 1 5 2 6 3 7 4 8 1. 2. 3. 4. 5. 6. 7. 8. CONNECTING THE WIRELESS REMOTE SPEAKER Clock set Mute Volume down Audio source selection Remote learner Equalizer Volume up Power on / off CAUTION To avoid being exposed to any radio frequency emission, the Wireless Remote Speaker and Transmitter should be placed at least 20cm (8 in) away from nearby persons.
Use the Y audio cable to connect audio source Transmitter: 2. Plug your AC adaptor into an electrical socket. to the NOTE Always use the supplied 9V AC power adaptor that is designed specifically for the Transmitter only. Using any other AC power adaptor may cause the unit to malfunction and increase the risk of fire or injury. 1. On one end of the cable are red / white connectors. Plug them into the RCA red / white input jack at the back of the Transmitter. 2.
EN POWER ON / OFF 1. To turn on the Wireless Remote Speaker, press the button located on the unit's Control Panel. The volume bar, speaker icon, clock, reception status icon and audio source number all appear on the LCD. The LCD backlight also turns on. NOTE In a non-controlled environment, many factors can affect battery life, such as volume, LCD backlight and temperature. When the batteries are not used for a long period of time, remove them to save battery power.
EN NOTE If you increase (or decrease) the volume while the speaker is on mute, the Mute function will deactivate and the volume will turn on again. ADJUSTING BASS AND TREBLE Adjusting the Wireless Remote Speaker's bass and treble settings allows the device to playback audio with a different range of sound and tonal effects. To adjust the bass sound: 1. Press the button once. appears on the LCD. NOTE The clock can only be adjusted by minute increments and not by hour increments. 2.
EN TIP The distance between remote control device and speaker should be no more than approximately 38 mm (1.5 inches) apart. This is to ensure the infrared signal from the audio source's remote control device is captured by the Wireless Remote Speaker during the learning session. LEARNING TO ACTIVATE THE MUTE FUNCTION USING THE AUDIO SOURCE REMOTE CONTROL DEVICE To teach your remote control device to activate the Mute function: button 3 times or once if you were 1.
The batteries may have run out of power or are not correctly aligned with their polarity. Re-install batteries checking the polarity; if the unit still does not operate, insert new batteries into the unit. How do I eliminate the severe hum, distortion or noise that is coming from the Wireless Remote Speaker? The speaker may be positioned too closely to the audio source, such as a TV or radio. Move the speaker at least 0.9 meters (3 feet) away from the source.
EN The wrong audio source may have been selected. Check that the correct source is selected and make sure to point the remote control device directly toward the infrared sensor. How do I eliminate signal jamming or interference? Signals transmitted from devices nearby may jam or interfere with signals transmitted from the transmitter to speaker. If there is signal jamming or interference, try changing the channel on both units (from A to B or B to A).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.