User Guide

ManualsBrandsOricom ManualsOtherPMR1000R

Stay in touch for FREE with Oricom

User Guide

Oricom PMR1000R

High Powered 1 Watt

UHF Two-Way Radios

Read this manual

carefully before use.

Stay in touch for FREE with Oricom

Highly sophisticated: You can communicate when you are out and about enjoying sport

and leisure activities, whilst at work or out on a job site.

Long range: With a massive 1 watt of power you can expect up to 7km range

depending on terrain and environmental conditions. The range is longer when using the

duplex feature.

Free communication: No call costs.

No license required: Start using your Oricom PMR1000R radios straight away.

Highly compact: Lightweight and small, they easily fit in your pocket or bag, or clip

them on your belt with the clips included.

Smart features: Advanced features include 40 UHF channels, long in use time, range

extender in duplex mode, channel scan, hands-free with or without a headset and Roger

beep confirmation tone.

Channel scan: Lets you easily find your group’s channel by searching all possible channels.

12-month replacement warranty

Summary of content (12 pages)

PAGE 1
Highly sophisticated: You can communicate when you are out and about enjoying sport and leisure activities, whilst at work or out on a job site. Long range: With a massive 1 watt of power you can expect up to 7km range depending on terrain and environmental conditions. The range is longer when using the duplex feature. Free communication: No call costs. No license required: Start using your Oricom PMR1000R radios straight away.
PAGE 2
Important Important information information Contact Contact us us Important safety information • Do not use the radios in areas where there is a risk of explosion, such as fuel stores, blasting areas, chemical stores or areas in which chemicals or other solids are present in the air. Always follow all information signs. Areas at risk of explosion are not always clearly marked however. • Changing battery packs/batteries in areas at risk of explosion means a danger to life.
PAGE 3
Safety and general information Warranty Warranty information information Exposure to Radio Frequency (RF) energy This product is covered by a 12-month warranty against defective workmanship or parts. The warranty does not extend to damage caused by misuse, negligence, water ingress, battery leakage or lightning. This guarantee in no way affects your statutory rights. Full details of the warranty are contained in the enclosed warranty card. Your radio contains both a receiver and transmitter.
PAGE 4
Your Your Oricom Oricom PMR1000R PMR1000R radio radio controls controls Attaching Attaching the the belt belt clips clips Attaching the belt clips (2 included) Each radio is supplied with a belt clip. Headset socket Menu button Indicator light To attach, simply slide into place. Display illumination On/off button Volume and menu settings Removing the belt clip To remove, release the clip with a screwdriver and slide upwards as shown.
PAGE 5
Your Your Oricom Oricom PMR1000R PMR1000R radio radio display display Changing Changing the the faceplates faceplates Additional coloured faceplates Your radios are supplied with additional coloured faceplates, which you can change as required. Keypad lock Scan Rodger beep Battery level Fixing the faceplate 1. Take the new faceplate and place it on the radio. 2. Then clip the faceplate into place. Duplex mode Hi power VOX Channel 4 19 Position 1 → CTCSS code Removing the faceplate 1.
PAGE 6
Installing Installing the the batteries batteries Each radio uses a Ni-Mh rechargeable battery pack (supplied). Or 4 AAA alkaline batteries (not supplied). Warnings • Do not mix old and new batteries. • Do not charge alkaline or non rechargeable batteries as they could explode and cause injury. • If you are not using the radios for an extended period remove the batteries.
PAGE 7
1. Ensure radio is turned off. Remove the belt clip on the back. → 2. Locate the clip on the battery cover. Use your fingernail to gently prise open the battery cover and remove. Automatic energy saving mode The radios are designed with a power saving mode. If no transmissions take place within a certain time, the unit switches itself off automatically. The time can be set to 30, 60 or 90 minutes. In setting 0, energy saving mode is switched off. 1. Press the button five times.
PAGE 8
Using Using the the twin twin charging charging kit kit 2. Select sensitivity level 1, 2 or 3 by using or . Choose - 1- If you speak loudly, or are in a noisy environment. 2- Suitable for most applications. 3- If you speak softly, or are in a quiet environment. Note: When you connect a VOX headset, the radio will automatically be set to the last chosen VOX sensitivity level. If IVOX is active, the radio will automatically select IVOX level.
PAGE 9
Turning your radio on and off Press and hold for two seconds to turn your radio on. The radio chirps and the display will show all feature icons for a brief period. Press and hold button for 2 seconds to turn off your radio. Adjusting the volume level When turned on, simply press listening level. or button to adjust the volume to a comfortable How to use the IVOX feature This feature allows you to transmit “hands-free” by talking into the radio microphone without using the headset. 1.
PAGE 10
Talking and listening It is good radio etiquette to monitor the channel for activity before you transmit, to ensure that you do not interrupt other users already on the channel. 1. Select the repeater channel in your area (channel 1 to channel 8). 2. Press the menu button 4 times to enter duplex mode, press or between duplex and simplex mode. Press and hold the button to check for channel activity. If you hear static, the channel is clear for use. Your radio has 40 channels.
PAGE 11
1. Press 2. Use 3. Press or until the code number begins to flash. to select required CTCSS tone 0 (off) or 1-38. to set the new code. Channel scan By scanning, you can monitor channels and codes for transmissions and lock in on the one that interests you. More importantly, you can find someone in your group who has accidentally changed channels and is talking during your scan. 1. To start scanning, briefly press and release the button. 2.
PAGE 12
You can specify a different code for each channel. 1. To set a channel and CTCSS code combination, press and then press or to select the channel. 2. Press again and then press or to select a CTCSS code. 3. You can not select interference eliminator codes on channel 5 or channel 35. On this channel press . The radio shall skip the codes setting. 4. Press to exit the menu and to save the channel and code combination. To set another channel and code combination, repeat these steps.