Thecus N4200 User’s Manual
Copyright and Trademark Notice Thecus and other names of Thecus products are registered trademarks of Thecus Technology Corp. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. Apple, iTunes and Apple OS X are registered trademarks of Apple Computers, Inc. All other trademarks and brand names are the property of their respective owners. Specifications are subject to change without notice. Copyright © 2009 Thecus Technology Corporation. All rights reserved.
Safety Warnings For your safety, please read and follow the following safety warnings: • Read this manual thoroughly before attempting to set up your N4200. • Your N4200 is a complicated electronic device. DO NOT attempt to repair it under any circumstances. In the case of malfunction, turn off the power immediately and have it repaired at a qualified service center. Contact your vendor for details.
Table of Contents Copyright and Trademark Notice ................................................... 2 About This Manual ......................................................................... 2 Limited Warranty........................................................................... 2 Safety Warnings ............................................................................ 3 Table of Contents .......................................................................... 4 Chapter 1: Introduction .......
Logs .......................................................................................... 26 System Management ...........................................................................27 Time: Setting system time ............................................................ 27 Notification configuration .............................................................. 27 Firmware Upgrade ....................................................................... 28 UPS Setting ..............................
ISO Mount .................................................................................. 75 User and Group Authentication............................................................78 ADS/NT Support .......................................................................... 78 Local User Configuration ............................................................... 80 Add Users................................................................................... 81 Edit Users ................................
Hard Drive Damage.................................................................... 115 Replacing a Hard Drive ............................................................... 115 RAID Auto-Rebuild ..................................................................... 115 Chapter 7: Troubleshooting ....................................................... 116 Forgot My Network IP Address .......................................................... 116 Can't Map a Network Drive in Windows XP ...................
Appendix E: UPS Compatibility List............................................ 142 Appendix F: Licensing Information ............................................ 146 Overview ........................................................................................... 146 Source Code Availability .................................................................... 146 CGIC License Terms........................................................................... 147 GNU General Public License ..................
Chapter 1: Introduction Overview Thank you for choosing the Thecus N4200 IP Storage Server. The Thecus N4200 is an easy-to-use storage server that allows a dedicated approach to storing and distributing data on a network. Data reliability is ensured with RAID features that provide data security and recovery—over ten Terabyte of storage is available using RAID 5 and RAID 6.
Media Server With the built-in Media Server capability, the N4200 provides media streaming service to stand-alone networked home media adapters that support the UPnP AV protocol or are Digital Living Network Alliance (DLNA) standard compliant. To set up the Media Server, refer to Chapter 4: System Network >Media Server. Backup Server Don’t leave precious data to chance.
Package Contents Your N4200 package should contain the following items: z z z z z z z z N4200 Unit x1 Power adapter x1 QIG (Quick Installation Guide) x1 CD-Title x2 (DriveClone5 Pro CD & Universal CD) Ethernet Cable x1 Screw Kit & Key-Luck x1 HDD Compatibility list Card x1 Multiple Languages Warranty Card x1 Please check to see if your package is complete. If you find that some items are missing, contact your dealer.
Front Panel The Thecus N4200’s front panel has the device’s controls, indicators, and hard disk trays: Front Panel Item Power Button OLED OLED Description • Power on/off N4200 • Displays current system status and messages • OLED screen saver will be enabled after screen is left idle for more than 3 mins • OLED screen will be diabled after it is left idle for more than 6 mins HDD 1 LED • Yellow: HDD activity • Red: HDD failure HDD 2 LED • Yellow: HDD activity • Red: HDD failure HDD 3 LED • Yellow: HDD act
Rear Panel The N4200 rear panel features ports and connectors. Item Power Connector WAN Port • For connect the power adaptor • WAN port for connecting to an Ethernet network through a switch Description LAN Port • LAN port for connecting to an Ethernet network through a switch or USB Ports • USB 2.
Chapter 2: Hardware Installation Overview Your N4200 is designed for easy installation. To help you get started, the following chapter will help you quickly get your N4200 up and running. Please read it carefully to prevent damaging your unit during installation. Before You Begin Before you begin, be sure to take the following precautions: 1. Read and understand the Safety Warnings outlined in the beginning of the manual. 2.
Cable Connections To connect the N4200 to your network, follow the steps below: 1. Connect an Ethernet cable from your network to the WAN port on the back panel of the N4200. 2. Connect the provided power cord into the universal power socket on the back panel. Plug the other end of the cord into a surge protector socket. 3. Press the power button on the Front Panel to boot up the N4200.
Chapter 3: First Time Setup Overview Once the hardware is installed, physically connected to your network, and powered on, you can configure the N4200 so that it is accessible to your network users. There are two ways to set up your N4200: using the Thecus Setup Wizard or the OLED display. Follow the steps below for initial software setup. Thecus Setup Wizard The handy Thecus Setup Wizard makes configuring N4200 a snap. To configure the N4200 using the Setup Wizard, perform the following steps: 1.
6. Name your N4200 and configure the network IP address. If your switch or router is configured as a DHCP Server, configuring the N4200 to automatically obtain an IP address is recommended. You may also use a static IP address and enter the DNS Server address manually. 7. Change the default administrator password. 8. Finished! Access the N4200 Web Administrator Interface by pressing the Start Browser button. You can also configure another N4200 at this point by clicking the Setup Other Device button.
NOTE The Thecus Setup Wizard is designed for installation on systems running Windows XP/2000 or Mac OSX or later. Users with other operating systems will need to install the Thecus Setup Wizard on a host machine with one of these operating systems before using the unit. OLED Operation The N4200 is equipped with an OLED on the front for easy status display and setup. There are four buttons on the front panel to control the OLED functions.
The N4200 will rotate these messages every one-two seconds on the OLED display. USB Copy The USB Copy function enables you to copy files stored on USB devices such as USB disks and digital cameras to the N4200 by press button. To use USB copy, follow the steps below: 1. Plug your USB device into an available USB port on the Front end. 2. In Display Mode, press the Down Button (▼). 3. The OLED will display “USB Copy?” 4.
Step 1: Network Setup From the Web Administration Interface, you can configure the network settings of the N4200 for your network. You can access the Network menu from the menu bar. For details on how to configure your network settings, refer to Chapter 4: System Network . Step 2: RAID Creation Next, administrators can configure their preferred RAID setting and build their RAID volume.
Printer Server Photo Server 21
Chapter 4: System Administration Overview The N4200 provides an easily accessible Web Administration Interface. With it, you can configure and monitor the N4200 anywhere on the network. Web Administration Interface Make sure your network is connected to the Internet. To access the N4200 Web Administration Interface: 1. Type the N4200’s IP address into your browser. (Default IP address is http://192.168.1.100) b NOTE Your computer’s network IP address must be on the same subnet as the N4200.
Menu Bar Item System Information System Management System Network Storage User and Group Authentication Application Server Module Management Backup Description Current system status of the N4200. Various N4200 system settings and information. Information and settings for network connections, as well as various services of the N4200. Information and settings for storage devices installed into the N4200. Allows configuration of users and groups. Printer Server and iTunes Server to set up of the N4200.
Temperature. Network. Green: Systematic temperature is normal. Red: Systematic temperature is unusual. Click to go to System Status page as short cut. Green: Connection to network is normal. Red: abnormal connection to the network Logout Click to logout Web Administration Interface.
Product Information Item Description Manufacturer Displays the name of the system manufacturer. Product No. Shows the model number of the system. Firmware version Shows the current firmware version. Up time Displays the total run time of the system. System/Service Status From the Status menu, choose the System item, System Status and Service Status screens appear. These screens provide basic system and service status information.
Logs From the System Information menu, choose the Logs item and the System Logs screen appears. This screen shows a history of system usage and important events such as disk status, network information, and system booting.
System Management The System Management menu gives you a wealth of settings that you can use to configure your N4200’s system administration functions. You can set up system time, system notifications, and even upgrade firmware from this menu. Time: Setting system time From the time menu, choose the Time item and the Time screen appears. Set the desired Date, Time, and Time Zone. You can also elect to synchronize the system time on the N4200 with an NTP (Network Time Protocol) Server.
Notification Configuration Item Description Beep Notification Enable or disable the system beeper that beeps when a problem occurs. Email Notification Enable or disable email notifications of system problems. SMTP Server Specifies the hostname/IP address of the SMTP server. Port Specifies the port to send outgoing notification emails. Auth Type Select the SMTP Server account authentication type. SMTP Account ID Set the SMTP Server Email account ID. Account Password Enter a new password.
Follow the steps below to upgrade your firmware: 1. Use the Browse button to find the firmware file. 2. Press Apply. 3. The beeper beeps and the Busy LED blinks until the upgrade is complete. NOTE • The beeper only beeps if it is enabled in the System Notification menu. • Check Thecus website for the latest firmware release and release notes. • Downgrading firmware is not permitted. WARNING Do not turns off the system during the firmware upgrade process.
See the following table for a detailed description of each item. UPS Setting Item UPS Monitoring Manufacturer Model Battery Status Power Seconds between power failure and first notification Seconds between subsequent power failure notifications Shutdown the system when the battery charge is less than Apply Description Enable or disable UPS monitoring. Choose the UPS manufacturer from the dropdowns. Choose the UPS model number from the dropdowns.
Example - Monday: On: 8:00; Off: 16:00 System will turn on at 8:00 AM on Monday, and off at 16:00 on Monday. System will turn on for the rest of the week. If you choose an on time, but do not assign an off time, the system will turn on and remain on until a scheduled off time is reached, or if the unit is shutdown manually. Example - Monday: On: 8:00 System will turn on at 8:00 AM on Monday, and will not shut down unless powered down manually.
From the menu, choose the SNMP item, and the SNMP Support screen appears. From here, you can Enable or Disable. Utility ˙ Administrator password From the menu, choose the Administrator Password item and the Change Administrator Password screen appears. Enter a new password in the New Password box and confirm your new password in the Confirm Password box. Press Apply to confirm password changes. There is also password for enter OLED setting you could setup here.
Confirm Password Apply Type the new password again to confirm. Press this to save your changes. ˙ Config Mgmt From the menu, choose the Config Mgmt item and the System Configuration Download/Upload screen appears. From here, you can download or upload stored system configurations. See the following table for a detailed description of each item. System Configuration Download/Upload Item Description Download Save and export the current system configuration.
˙ Reboot & Shutdown From the menu, choose Reboot & Shutdown item, and the Shutdown/Reboot System screen appears. Press Reboot to restart the system or Shutdown to turn the system off. ˙ File System check The File System Check allows you to perform a check on the integrity of your disks’ file system. Under the menu, click File system Check and the File System Check prompt appears. To perform a file system check, click Apply. Once clicked, the following prompt will appear: Click Yes to reboot the system.
Once the system has rebooted, you will be returned to the File System Check prompt. There you will see the available RAID volumes to run the file system check on except ZFS volume, ZFS has no need to perform file system check. Check the desired RAID volumes and click Next to proceed with the file system check. Click Reboot to reboot without running the check. Once you click Next, you will see the following screen: Click Start to begin the file system check. Click Reboot to reboot the system.
NOTE The system must be rebooted before the N4200 can function normally after file system check complete. System Network Use the System Network menu to make network configuration settings as well as service support settings. WAN Configuration From the System Network menu, choose WAN, and the WAN Configuration screen appears. This screen displays the network parameters of the WAN connection. You may change any of these items and press Apply to confirm your settings.
WAN Configuration Item Description Host name Domain name Host name that identifies the N4200 on the network. Specifies the domain name of the N4200. WINS Server To set a server name for NetBIOS computer. MAC Address MAC address of the network interface. Jumbo Frame Support Enable or disable Jumbo Frame Support of the WAN interface on your N4200. IP Sharing Mode When enabled, PCs connected to the LAN port will be able to access the WAN.
WARNING Most Fast Ethernet (10/100) Switches/Routers do not support Jumbo Frame and you will not be able to connect to your N4200 after Jumbo Frame is turned on. If this happens, turn off the N4200. Then, insert USB disk with factory reset utility included and power on the N4200. Till the system power on complete then it will bring your system settings back to factory default. LAN LAN Configuration The N4200 supports two Gigabit Ethernet ports for higher service availability.
NOTE WARNING The IP Segment of WAN and LAN should not overlap. The IP address of the LAN interface should not be in the range of the Start IP address and End IP address. Samba / CIFS There are 4 options is currently allow Admin to Enable/Disable to operate N4200 associated with Samba / CIFS protocol. With the option changed, it will need to reboot system to activate.
Samba Anonymous Login Authentication To enable this option, no matter there is share folder has been created in public access. The user account and password is needed from system to access under SMB/CIFS protocol. On the other hand, no more anonymous login is allowed. NOTE • In some environments, due to security concerns, you may wish to disable SMB/CIFS as a precaution against computer viruses.
A description of each item follows: NFS Apply NFS Server Setting Item Description Enable or Disable NFS support. Click Apply to save your changes. FTP N4200 can act as a FTP server, enabling users to download and upload files with their favorite FTP programs. From the System Network menu, choose the FTP item, and the FTP screen appears. You can change any of these items and press Apply to confirm your settings.
Security FTP Port FTP ENCODE Allow Anonymous FTP Access Auto Rename Upload Bandwidth Download Bandwidth Enable or disable Security FTP, be sure the client FTP software has also security FTP setting enabled. Specifies the port number of an incoming connection on a non-standard port. If your FTP client or operating system does not support Unicode (e.g. Windows® 95/98/ME or MAC OS9/8), select the same encoding as your OS here in order to properly view the files and directories on the server.
A description of each field follows: Media Manager Settings Item Description Media Server Enable or disable the Media Server service. Shared Media Folders Select the folder(s) that contains media files to be shared. Rescan Click the Rescan button to have the N4200 for new contents in the selected media folder. Share Media Folders Once the Media Server software is installed, you can start adding folders that contain the media that you would like to share.
4. Setup the DMA (These steps will be different if you use a different DMA) a. From the Server List screen, select “N4200: Media Server” as the server. b. Go to My Media c. Click on the Up/Down Arrow buttons to select Music Jukebox, Photo Albums, or Video Clips d. Start enjoying the contents stored in your N4200. HTTP/ Web Disk From the System Network menu, choose the HTTP/ Web Disk item, and the Web Disk (HTTP) Support screen appears. This screen displays the service support parameters of the system.
UPnP This device supports UPnP Media server, which allows users to play media files with UPnP client (ex. DMA devices). Enable or disable Universal Plug and Play protocol. UPnP helps to find the IP address of the N4200. Nsync Target From the System Network menu, choose the Nsync Target item, and the Nsync Setting screen appears. Enable or Disable your Nsync Target Server. Press Apply to confirm your settings.
through Bonjour zero-configuration networking with a complete description of the protocols and technologies used to create Bonjour enabled applications and devices. Storage Management The Storage menu displays the status of storage devices installed in the N4200, and includes storage configuration options such as RAID and disk settings, folder configuration, space allocation and ISO Mount. Disks Information From the Storage menu, choose the Disks item and the Disks Information screen appears.
Bad Block scan Total Capacity Disk Power Management NOTE Yes to start scan Bad Block. Shows the total SATA hard disk capacity. The administrator can set the disk to power down after a period of inactivity. When the Status shows Warning, it usually means there are bad sectors on the hard disk. It is shown only as a precaution and you should consider changing the drives. S.M.A.R.T. Information On the Disks Information screen, the status of each disk will be displayed in the Status column.
Current Pending Sector Test Type Current count of unstable sectors (waiting for remapping). The raw value of this attribute indicates the total number of sectors waiting for remapping. Later, when some of these sectors are read successfully, the value is decreased. If errors still occur when reading sectors, the hard drive will try to restore the data, transfer it to the reserved disk area (spare area), and mark this sector as remapped.
RAID Information Item Description Master RAID The RAID volume currently designated as the Master RAID volume. ID ID of the current RAID volume. NOTE: All RAID IDs must be unique. RAID Level Shows the current RAID configuration. Status Indicates status of the RAID. Can read either Healthy, Degraded, or Damaged. Disks Used Hard disks used to form the current RAID volume. Total Capacity Total capacity of the current RAID. Data Capacity Indicates the used capacity and total capacity used by user data.
2. On the RAID Configuration screen, set the RAID storage space as JBOD, RAID 0, RAID 1, RAID 5, RAID 6, or RAID 10 — see Appendix C: RAID Basics for a detailed description of each. 3. Specify a RAID ID. 4. If this RAID volume is meant to be the Master RAID volume, tick the Master RAID checkbox. NOTE In a multiple RAID configuration, one RAID volume must be designated as the Master RAID volume. The Master RAID volume will store all installed modules. If the Master RAID is changed to another location (i.e.
NOTE Building a RAID volume may take time, depending on the size of hard drives and RAID mode. In general, while the RAID volume building process is up to “RAID Building” then the data volume is capable to be accessed. WARNING Creating RAID destroys all data in the current RAID volume. The data is unrecoverable. With a RAID 1, RAID 5, RAID 6, or RAID 10 volume, you can also add a spare disk after the RAID is created. See Chapter 6: Tips and Tricks > Adding a Spare Disk for details.
RAID 6 RAID 10 WARNING RAID 5 requires a minimum of 3 disks. RAID 5 can sustain one failed disk. Two independent parity computations must be used in order to provide protection against double disk failure. Two different algorithms are employed to achieve this purpose. RAID 6 requires a minimum of 4 disks. RAID 6 can sustain two failed disks. RAID 10 has high reliability and high performance. RAID 10 is implemented as a striped array whose segments are RAID 1 arrays.
Remove RAID Click to remove the RAID volume. All user data and iSCSI has been created in selected RAID volume will be removed. To remove a RAID volume, follow the steps below: 1. On the RAID List screen, select the RAID volume by clicking on its radio button, and click RAID Information to open the RAID Configuration screen. 2. On the RAID Configuration screen, click Remove RAID. 3.
WARNING Remove RAID destroys all data in the current RAID volume. The data is unrecoverable. Expanding a RAID To expand a RAID 1, RAID 5, RAID 6, or RAID 10 volume, follow the steps below: 1. Replace one of the hard drives in the RAID volume and allow it to automatically rebuild. 2. Once rebuilt, you can continue to replace any remaining disks in the RAID array. 3. When you are done replacing hard drives, log on to Web Management. Navigate to Storage> RAID to open the RAID Configuration screen. 4.
Migrating a RAID Once a RAID volume has been created, you may want to move it to other physical drives or change the RAID array all together. To migrate a RAID 0, RAID 1, RAID 5 or RAID 6 volume, follow the steps below: 1. From the RAID Configuration screen, click Migrate RAID. 2. A list of possible RAID migration configurations will be listed. Select the desired migration scheme and click Apply. 3. The system will begin migrating the RAID volume.
NOTE Migrating a RAID volume could take several hours to complete With RAID level migration function, it has two different type “On line” and “Off line” alone with limitation as listed below. 1. During RAID level migration, it is not allowed reboot or shutdown system. 2. Off line RAID level migration, all services will stop and data is inaccessible. 3.
Below is a table listing of possible RAID migration schemes: To From RAID 0 RAID 5 RAID [OFFLINE] 0 [RAID 0] HDDx2 to [RAID 0] HDDx3 [RAID 0] HDDx2 to [RAID 5] HDDx3 [RAID 0] HDDx2 to [RAID 0] HDDx4 [RAID 0] HDDx2 to [RAID 5] HDDx4 [OFFLINE] RAID 6 X [RAID 0] HDDx2 to [RAID 0] HDDx5 [RAID 0] HDDx2 to [RAID 5] HDDx5 [RAID 0] HDDx2 to [RAID 0] HDDx6 [RAID 0] HDDx2 to [RAID 5] HDDx6 [RAID 0] HDDx2 to [RAID 0] HDDx7 [RAID 0] HDDx2 to [RAID 5] HDDx7 [RAID 0] HDDx3 to [RAID 0] HDDx4 [RAID 0] HDDx3 to [RA
RAID X X [ONLINE] [RAID 6] HDDx4 to [RAID 6] HDDx5 6 [RAID 6] HDDx4 to [RAID 6] HDDx6 [RAID 6] HDDx4 to [RAID 6] HDDx7 [RAID 6] HDDx5 to [RAID 6] HDDx6 [RAID 6] HDDx5 to [RAID 6] HDDx7 [RAID 6] HDDx6 to [RAID 6] HDDx7 Space Allocation You may specify the space allocated for iSCSI volumes. The iSCSI volume can be created up to 5 volumes per RAID volume. To do this, under the Storage menu, click RAID and the RAID List window appears.
Allocating Space for iSCSI Volume To allocate space for an iSCSI volume on the current RAID volume, follow the steps below: 1. Under the Volume Allocation List, click iSCSI Target. The Create iSCSI Volume screen appears. Create iSCSI Volume Item Description RAID ID ID of current RAID volume. Allocation Percentage and amount of space allocated to iSCSI volume. Unused Percentage and amount of unused space on current RAID volume. iSCSI Target Volume Enable or Disable the iSCSI Target Volume.
Month Username Password Password Confirm Select the current month from the dropdown. Enter a username. Enter a password. Reenter the chosen password 2. Designate the percentage to be allocated from the Allocation drag bar. 3. Enable the iSCSI Target Service by selecting Enable. 4. Choose to enable CHAP authentication or choose None. 5. Enter a Target Name. This will be used by the Stackable NAS function to identify this export share. 6. Choose the current year from the Year dropdown. 7.
2. Modify your setting. Press ok to change. Delete Volume To delete volume on the current RAID volume, follow the steps below: 1. Under the Volume Allocation List, click Delete. The Space Allocation screen appears.
2. Press YES. All data in the volume will be removed. Advance Option There are 2 options is currently allow Admin to Enable/Disable to operate N4200 associated with iSCSI setting. The details as listed in following screenshot. With the option changed, it will need to reboot system to activate. iSCSI Block Size Select the block size with 4K while the iSCSI volume size is over 2TB. iSCSI CRC/Checksum To enable this option, the initiator can connect with “Data digest” and “Header digest” enabled.
Adding Folders On the Folder screen, press the Add button and the Add Folder screen appears. This screen allows you to add a folder. After entering the information, press Apply to create new folder.
Add Folder Item RAID ID Folder Name Description Browseable Public Share Folder Limit Apply NOTE Description RAID volume where the new folder will reside. Enter the name of the folder. Provide a description the folder. Enable or disable users from browsing the folder contents. If Yes is selected, then the share folder will be browseable. Admit or deny public access to this folder. If Yes is selected, then users do not need to have access permission to write to this folder.
Description Browseable Public Share Limit Provide a description the folder. Enable or disable users from browsing the folder contents. This setting will only apply while access via SMB/CIFS and web disk. Admit or deny public access to this folder. Enter the maximum size of the folder. The folder will not grow beyond this limit. You can enter a 0 to turn off the share folder limit. Remove Folders To remove a folder, press the Remove button from the specified folder row.
NFS Share Item Hostname Privilege Guest System Support IO Mapping Apply Description Enter the name or IP address of the host Host has either read only or writeable access to the folder. There are two selections available: • Unix / Linux System • AIX (Allow source port > 1024) Choose the one which best fits your needs. There are three selections available: • Guest system root account will have full access to this share (root:root).
Snapshot The N4200 is capable for 16 snapshot version control. To have snapshot to work on, the file system creation for RAID volume has to be “ZFS”. Snap (Snapshot configuration) If added folder has located in the RAID volume with “ZFS” file system, then the folder management screen with “Snap” button will be configurable. Snapshot Item Take Shot Remove Schedule Description Click to take snapshot right away. Click to remove snapshot schedule. Click to open snapshot schedule setup screen.
These taken snapshot is only accessible though CIFS/SMB by manually type \\NAS IP address\snapshot and invisible from normal access. Also, the taken snapshot version is read only can not be deleted under CIFS/SMB access but only click the “Del” button showing on the screen shot above. Folder and sub-folders Access Control List (ACL) On the Folder screen, press the ACL button, and the ACL setting screen appears.
2. With the group or user selected, press one of the buttons from the three access level columns at the top. The group or user then appears in that column and has that level of access to the folder. 3. Continue selecting groups and users and assigning them access levels using the column buttons. 4. To remove a group or user from an access level column, press the Remove button in that column. 5. When you are finished, press Apply to confirm your ACL settings.
NOTE The system will list up to 1,000 users from the chosen category. To narrow your search, enter a search term in the blank provided. Stackable NAS The N4200’s capacity can be expanded even further using the stackable function. With it, users can expand the capacity of their network storage systems up to 5 other stack target volumes which are located in different systems. These can be stacked through single network access like SMB or AFP acting as a share folder type.
Next, input the target IP address of the stackable device and click the Discovery button. The system will list available target volumes from the inputted IP address. Once IP with volume have been set, you may need to input a valid user name and password to validate your access rights. If there is no user name and password needed to access target volume, then leave it blank. Once IP with volume have been set, you may need to input a valid user name and password to validate your access rights.
From the figure above, the Export share name is “pmmeeting”. The figures below show the result before and after via Microsoft Network Access with settings have been completed. No Stack Target Stack target with export share name “pmmeeting” The Browseable setting will be same method of setting for system share folder. It designates whether or not this folder will be visible through web disk. You may refer the figures below for reference when Yes and No are selected.
The Public setting will be set same as what the setting for the system share folder associated with the ACL permission setup. If Public is set to Yes, all users will be able to access it, and ACL button will be grayed out. If Public is set to No, the ACL button will be available on the Stack Target List window. Click Apply to save your changes. B. Activate a Stack Target After your settings have been applied, the system will bring you back to Stack Target List window as shown below.
With this newly attached stack target device, you will see the information displayed and also several options you can choose. In general, if attached stack target device has been used by another N5200PRO/1U4500/N5500/N4200/N4200/N8800 as stack target volume, then the Format item will be display and system will recognize it straight away and display its capacity. Otherwise, the Format item will be available and the Capacity and Status items will show as “N/A” and “Unknown file system” respectively.
ACL settings will be exactly the same as system folder that you may have setup previously. E. Reconnect a Stack Target The enabled stack target devices may be disconnected by situations such as power outages or network disconnects. When this happens, the Reconnect button will available. To attempt to reconnect the stack target, click Reconnect. ISO Mount The ISO Mount feature is very useful tool from Thecus products.
From the main menu, the ISO Mount feature is located under “Storage”. Please refer the figure below for reference. Select on the ISO mount function and you will have the screen shot appear as following. A. Add a ISO file From the figure above, select ISO file from drop down share list. After selection, system will bring up Mount table for further setting screen.
To mount new ISO file, select from listed ISO file and input desired mounting name into “Mount as:” field. Click “ADD” with confirmation to complete mounting ISO file. Or without “Mount as” ISO file export name input, system will automatic to give the export name by ISO file name. If left “Mount as:” blink then system will create mount point by ISO file name.
You could click “Unmount” to eliminate mounted ISO file. B. Using ISO The mounted ISO file will be located same share folder with name giving. Please refer the screen shot below. ISO file “image” has mounted as folder “Image” you could see. The ISO file “Thecus 01” without assign mounting name, system automatically has folder “Thecus 01” created. User and Group Authentication The N4200 has built-in user database that allows administrators to manage user access using different group policies.
support feature; the N4200 will connect with the ADS/NT server and get all the information of the domain users and groups automatically. From the Accounts menu, choose Authentication item and the ADS/NT Support screen appears. You can to change any of these items and press Apply to confirm your settings. A description of each item follows: ADS/NT Support Item Description Work Group / Domain Specifies the SMB/CIFS Work Group / ADS Domain Name (e.g. Name N4200).
To join an AD domain, you can refer the figure and use the example below to configure the N4200 for associated filed input: AD Domain Example Item Information Work Group / Domain domain Name ADS Support Enable ADS Server Name Computer1 ADS/NT Realm Domain.local Administrator ID Administrator Administrator *********** Password NOTE • The DNS server specified in the WAN configuration page should be able to correctly resolve the ADS server name.
Local User Configuration Item Description Add Press the Add button to add a user to the list of local users. Edit Press the Edit button to modify a local user. Remove Press the Remove button to delete a selected user from the system. Add Users 1. Click on the Add button on Local User Configuration screen, and Local User Setting screen appears. 2. On the Local User Setting screen, enter a name in the User Name box. 3. Enter a User ID number. If left blank, the system will automatically assign one. 4.
NOTE All users are automatically assigned to the ‘users’ group. Edit Users 1. Select an existing user from the Local User Configuration screen. 2. Click on the Edit button, and Local User Setting screen appears. 3. From here, you can enter a new password and re-enter to confirm, or use the << or >> buttons to have this user join or leave a group. Click the Apply button to save your changes.
Remove Users 1. Select an existing user from the Local User Configuration screen. 2. Click on Remove button and the user is deleted from the system. Local Group Configuration From the Accounts menu, choose the Group item, and the Local Group Configuration screen appears. This screen allows you to Add, Edit, and Remove local groups. Local Group Configuration Item Description Add Press the Add button to add a user to the list of local groups.
Add Groups 1. On the Local Group Configuration screen, click on the Add button. 2. The Local Group Setting screen appears. 3. Enter a Group Name. 4. Enter a Group ID number. If left blank, the system will automatically assign one. 5. Select users to be in this group from the Users List by adding them to the Members List using the << button. 6. Click the Apply button to save your changes. Edit Groups 1. On the Local Group Configuration screen, select a group name from the list. 2.
Remove Groups 1. On the Local Group Configuration screen, select a group name from the list. 2. Press Remove to delete the group from the system. Batch Create Users and Groups The N4200 can also add users and groups in batch mode. This enables you to conveniently add numerous users and groups automatically by importing a simple comma-separated plain text (*.txt) file. From the Accounts menu, click Batch Mgmt and the Batch Create Users and Groups dialogue will appear.
Application Server The N4200 supports printer server, and Tunes server. The integrated Print Server allows you to share a single USB printer will all users on the network. The N4200 provides activating the iTunes Server on the device. You will be able to play music files on this device with your iTunes client software directly. The following section shows you how. Printer Information From the Application Server menu, choose the Printer item, and the Printer Information screen appears.
If a corrupt print job is sent to a printer, printing may suddenly fail. If your print jobs seem to be locked up, pressing the Remove All Documents button to clear the print queue may resolve the issue. You can configure the N4200 to act as a printer server. That way, all PCs connected to the network can utilize the same printer. Windows XP SP2 To set up the Printer Server in Windows XP SP2, follow the steps below: 1.
Windows Vista To set up the Printer Server in Windows Vista, follow the steps below: 1. Open Printer Folder from the Control Panel. 2. Click the right mouse button in anywhere on the Printers folder and then select Add Printer. 3. Select Add a network, wireless or Bluetooth printer.
4. Select The printer that I want isn’t listed. You can press The printer that I want isn’t listed to go into next page without waiting for Searching for available printers to finish. 5. Click Select a shared printer by name. Type http://:631/printers/usb-printer in the box, where is the IP address of the N4200. Click Next. 6. Select or install a printer and then press OK.
If your printer model is not listed, please contact your printer manufacturer for help. 7. Windows will attempt to connect to the printer. 8. You can choose to set this printer as the default printer by checking the Set as the default printer box. Click Next to continue. 9. Done! Click Finish.
iTunes® Server With the built-in iTunes server capability, the N4200 enables digital music to be shared and played anywhere on the network! From the Network menu, choose the iTunes item, and the iTunes Configuration screen appears. You may enable or disable the iTunes Service from here. Once enabled, enter correct information for each field and press Apply to save your changes.
User Module The user module is reserved for Thecus fans to build up 3rd party functions in the future. Backup There are a number of ways to back up data with the N4200. Nsync You can backup a share folder to another N4200 (Nsync Target) or any FTP server for safe keeping as long as you have appropriate access right on that target. When using Nsync between two N4200s, you have the option to transmit files securely between two N4200s.
Add Nsync Task Item Description Task Name The name of your Nsync task. Target Server Select whether the target is a Thecus Product (e.g. N4200) or FTP Manufacturer server. Nsync Mode Synchronize mode or Incremental mode . Target Server IP The IP address of your target server. Address Source Folder The share folder you want to backup. Authorized Username The account name on the target server.
Password on Target Server Test Connection Schedule Time Type Add NOTE The password for the username on the target server. Click to check the connection to the Target Server. Enable or Disable schedule backup of your share folders. The time when the Nsync task will run. Select whether to run the Nsync task daily, weekly, or monthly. Daily: input the time of day to execute Nsync task. Weekly: input which day of the week to execute the task. Monthly: decide which day of the month to execute the task.
Thecus Backup Utility The Thecus Backup Utility is on your Installation CD. When you click on the CD, the Backup Utility will be installed under Program Groups > Thecus > Thecus Backup Utility. If it is not installed, you can copy the file (Thecus Backup Utility.exe) to a convenient location on your hard disk and double click to execute it. NOTE If you can not find Thecus Backup Utility on your CD, please download it from the Thecus website (http://www.thecus.com).
2. When the Welcome to Microsoft Windows XP screen appears, click Perform Additional Tasks. 3. Click Browse this CD. 4. In Windows Explorer, navigate to ValueAdd > Msft > Ntbackup. 5. Double-click Ntbackup.msi to install the backup utility. Once installed, you can use the Windows Backup Utility by following the steps below: 1. Click Start, and point to All Programs > Accessories > System Tools > Backup to start the wizard. 2. Click Next to skip past the opening page.
Chapter 5: Using the N4200 Overview Once the N4200 is setup and operating, users on the network may manage all varieties of digital music, photos, or files by simply using their web browsers. To manage your personal files or access public files on the N4200, just enter its IP address into your browser (default IP address is http://192.168.1.100), and you will be taken to the N4200 Login page.
6. To create a new folder within the current folder, press the New folder button. When the screen appears enter a name for the folder. Press OK to create the folder. 7. To upload a file from your computer to the current folder, press the New file (upload) button. When the screen appears, press Browse and locate the file to upload. Press OK and the file is uploaded to the current folder. 8. To delete a file or folder, select the file or folder’s check box. Press the Delete selected items button.
(Admin) Change password and confirm new password. (logout) To logout of the web disk interface. Show the files and folders in the directory. Search files in the directory. (You can only input some word string.) Name Displays the names of folders and files. Size Shows the size of folders and files. Type Displays the type of folders and files. Modified Shows the time of most recent modification of folders and files. owner Owner of the file.
Windows XP Publishing Wizard There are many ways for a local user to upload pictures into their photo album. Users of Windows XP can upload their pictures using the Windows XP Publishing Wizard. 1. Click on the XP Publishing Wizard icon on top right corner. 2. The XP Web Publishing Wizard Client screen appears. Click on the link to install the Publishing Wizard. 3. Windows XP will ask whether you want to run or save this file. Click Save to save the register file.
4. Once the register file is installed, use the Windows file manager to browse the folder that contains the picture you want to publish. On the left pane, there will be an icon labeled “Publish this folder to the Web”. 5. Click on this icon and Web Publishing Wizard will start. 6. Select the pictures you want to publish to the Photo Web Server by placing a check mark on the top left hand corner of the picture. Click Next.
7. Your PC will start to connect to the Photo Web Server. 8. Select N4200 Photo Gallery Wizard to publish your pictures to the N4200. 9. Login into the N4200 with your local user name and password. 10. Create your album by entering an album name and clicking on the Create Album button.
11. Select the album you want to upload your pictures to. 12. Confirm the target album. 13. Windows will show you that the picture upload is in progress.
14. When the upload is finished, the Wizard will ask you whether if you want to go to the website. Click Finish to go to your Photo Web Server. 15. Click on the user’s icon to go to that user’s album. 16. You will see the user’s album list. Click on Album.
17. Finished! You will see the pictures just selected in the album. Managing Albums and Photos Icon Function Description Make Cover Make selected photo your cover picture. Back Return to the previous screen. Add Add a new album or photos. Modify Edit the name and description of the selected album or photo. Each name is limited to 20 characters and each description is limited to 255 characters. Delete NOTE Delete the selected albums or photos. • Only logged in users will see these icons.
Creating Albums To create a photo album, follow the steps below: 1. Click the Add button to create a new album. 2. Enter a name for the album, and enter a description if you wish. Then, click on the Create Album button. Password Protecting Albums If you would like to put a password on a particular album, follow these steps: 1. Select the album to be protected, click on the Edit button, and the Album Edit screen will appear. 2.
Slide Shows Slide shows are a great way to enjoy pictures stored on your N4200. You can click on the Start Slide Show icon on the top right hand corner to start the slide show. To stop the slide show, click on the Stop Slide Show icon on the top right hand corner. Mapping a Client PC to the N4200 You can map share folders on the N4200 so that you can access them as if they were drives on your computer. You can connect to the shared network folders on the N4200 as follows: Windows 1.
1. Choose Go > Connect to Server… 2. Enter the network address for the server in the Server Address text box. When connecting using SMB/CIFS protocol, type: smb://192.168.1.100/Folder1 When connecting using AFP protocol, type: afp://192.168.1.100/Folder1 Click Connect. 3. When MAC OS X is trying to connect N4200, it will ask for a User Name and Password which has access to the folder. 4.
3. You will now install the iSCSI Initiator using the Setup Wizard. Click Next to continue. 4. Leave the default selections and click Next. 5. Read the license agreement. To continue with the installation, click I Agree and then click Next. 6. The iSCSI Initiator will now install automatically. Click Finish once completed.
7. Start the iSCSI Initiator by double-clicking its icon on the desktop. The iSCSI Initiator properties window will appear. 8. Select the Discovery tab. Under Target Portals, click Add. 9. Enter the IP address of the N4200. Click OK. 10. On the iSCSI Initiator Properties window, select the Targets tab. With the iSCSI target highlighted, click Log On. The Log On to Target dialogue will appear.
11. If you have not enabled CHAP, click OK to continue. If you have enabled CHAP, click Advanced. Under Advanced Settings, check the CHAP login information checkbox and enter your username and password. Click OK. 12. Right click My Computer on the desktop and select Manage.
13. Click on Disk Management and you will see a new hard disk listed. 14. Initialize the new hard disk and you will then be able to use the iSCSI target as a local drive. Windows Vista Because Windows Vista has the Microsoft iSCSI Initiator pre-installed, you will not have to install this piece of software. Instead, start the iSCSI Initiator and follow steps 8-14 to map the N4200 as an iSCSI drive.
Chapter 6: Tips and Tricks USB and eSATA Storage Expansion The N4200 supports external USB hard disks through its four USB ports. Once a USB hard disk has successfully mounted, the entire volume will be linked automatically to the default USB HDD folder. The N4200 supports up to 4 USB external storage devices. All file names on the USB disk volume are case sensitive. The N4200 also supports eSATA hard disks with its eSATA port.
Part I - Setup a DynDNS Account 1. Go to http://www.dyndns.org from your home PC. 2. Click on the Sign Up Now link. 3. Check the Check boxes, select a user name (i.e.: N4200), enter your email address (i.e.: xxx@example.com), check Enable Wildcard, and create a password (i.e.: xxxx). 4. Wait for an email from www.dyndns.org. 5. Open the email and click on the link to activate your account Part II - Enable DDNS on the Router 1.
Replacing Damaged Hard Drives If you are using RAID 1, RAID 5, or RAID 6 you can easily replace a damaged hard drive in the Thecus N4200 while keeping your data secure with the system’s automatic data recovery. Hard Drive Damage When a hard drive is damaged and data in the RAID volume, the system OLED will display warning message also the system beeps. Replacing a Hard Drive To replace a hard disk drive in the N4200: 1. Remove the tray with the damaged hard disk. 2.
Chapter 7: Troubleshooting Forgot My Network IP Address If you forget your network IP address and have no physical access to the system, you can find out the IP address by either looking directly onto the N4200’s OLED panel, or by using the setup wizard to retrieve the IP of your N4200. 1. Start the Setup Wizard, and it will automatically detect all Thecus IP storage products on your network. 2. You should be able to find the IP address of the N4200 which you have forgotten in the Device Discovery screen.
4. Set the Date, Time, and Time Zone. 5. Click Apply. In addition, if the N4200 is able to access the Internet and you want to keep the NTP Server clock.isc.org by default, please make sure the DNS Server is correctly entered, thereby allowing the NTP Server name to correctly resolve. (See System Network > WAN > DNS Server) Dual DOM Supports for Dual Protection The most advance and useful of N4200 is Dual DOM implemented. In the normal circumstance, it has no need to have this feature involved.
Chapter 8: Firmware Revise RAID Expansion for iSCSI Target Volume First, the iSCSI volume is now able to expand its capacity from unused space. From the volume list, simply select the iSCSI volume you like to expand and click the Expand button: You will then see the dialog box displayed below. Drag the Expand Capacity bar to the size you want. Then press Expand to confirm the operation. RAID Volume Encryption With firmware v3.00.
the Encryption option needs to be enabled while the RAID is created and followed by password input for identification. Also, an external writable USB disk plugged into any USB port on the system is required to save the password you have entered while the RAID volume is being created. See the screenshot below for details. Once the Create button has been pressed with the Encryption checkbox enabled, the following message pop-up will appear for confirmation.
RAID volumes with encryption enabled will be displayed with a key lock symbol next to volume ID name. iSCSI Thin-Provisioning An advanced thin-provisioning for iSCSI feature is available in this firmware release. With this function, the iSCSI capacity can be more flexible and more efficiently serve more users. The idea for iSCSI thin-provisioning is sharing the available physical capacity to a number of iSCSI target volumes and also setup virtual capacity to expand the physical size while it needed.
Next, setup the physical capacity for iSCSI thin-provision volume by dragging the Allocation bar to the desired size. After the size has been determined, click OK to confirm. Now you will see the iSCSI thin-provisioning volume is available from the list. Please refer to the screenshot below. Now you can start to create iSCSI targets to join the newly-created iSCSI thin-provision volume.
4. The limit is 5 iSCSI target volumes under thin-provisioning or a virtual size of 16000GB. iSCSI Thin-provision physical size starts with 333.8GB The virtual capacity is limited to 16000GB The screen shot for iSCSI target volume creation under thin-provisioning; the physical capacity 333.8GB. The screen shot to setup an iSCSI target volume under thin-provisioning of 1700GB.
iSCSI target volume creation. The maximum virtual size is 14300GB (16000GB – 1700GB(1st iSCSI target volume)). This screenshot lists iSCSI target volumes created under thin-provisioning. The 2nd iSCSI target volume under thin-provisioning has been created with a capacity of 14300GB. This message appears if there is no more room for new iSCSI target creation.
NOTE 1. Each RAID volume can only create one iSCSI thin-provision volume. 2. Each thin-provision volume can only create 5 iSCSI target volumes. 3. The notification will send out while the physical size of iSCSI thin-provision capacity has used up to 90%. iSCSI LUN ID When iSCSI target volume has been created, there is a default LUN ID of 0 in previous firmware versions which was un-configurable. From v3.00.
Chapter 9: Firmware Revise Updated Login User Interface There is a brand new design for the admin login UI. NOTE The previous chapters have screenshots of the original user interface. Please note that all changes are visual only. There are no functional changes. Updated Photo Server User Interface Same as the admin login user interface, the photo server has a brand new art design from its previous version.
Disclaimer Page Added The following disclaimer page has been added to this firmware release. Please click the check box if you do not want to have this page displayed during the next login.
Updated Main User Interface The look and icons of the main user interface have been updated. Add On-Line Register Service From main menu tree, there is a new “On-line Register” option added with this firmware release. This on-line register service can periodically update the user when new firmware and software modules are released by Thecus. To enable this service, simply check the “Enable” check box. By enabling this service, the items in bold will be sent to Thecus via the Internet.
Added Rsync Setting under Nsync Target The Thecus Nsync feature has added a third way to use Rsync to replicate data between two systems. For the target side to allow source cross data, the Rsync target server needs to first select “Enable” and then assign a username and password for authentication. NOTE The Rsync target server username and password is used for this replication feature only. It is not related to the standard local user.
enable the sync target server and input a valid username and password to grant access permission. Added 2nd Gateway for Clients of DHCP Server Route The adding of a 2nd gateway has been phased in to serve clients that use their Thecus NAS as a DHCP server to have another route to balance traffic bandwidth. NOTE If the IP sharing mode setting is set to “Enable” under WAN port, then this 2nd gateway cannot be configured.
Added Dual DOM for Auto Repair The unique Dual DOM feature can now perform “Auto Repair”. The Thecus NAS will backup up to five versions of the system configuration either by the default timing of 1:00am every day automatically or as scheduled by the user. This unique “Auto Repair” will be triggered if the primary DOM has a booting issue. In this instance, the 2nd DOM will take over the boot function.
Chapter 10: Version 3.01.00 Firmware Updates What’s New There are additional features implemented into the new 3.01.00 version firmware. Updated Login User Interface The design of the admin login UI has been completely updated. NOTE The previous chapters have screenshots of the original user interface. Please note that all changes are visual only. There are no functional changes. Updated Main User Interface The look and icons of the main user interface have been updated.
Administrators can add or remove favorite functions to My Favorites by right clicking the mouse on the menu tree. The other way administrators can add favorite functions is by clicking the “Add Favorite” icon in each function screen. Please refer figure below in red circuit icon. To return to the favorite screen, simply click “My Favorite” located at the left hand corner of the main screen.
Added Additional Mode Support for Link Aggregation Link Aggregation now has six supported modes. The administrator can choose the most suitable mode to fit the network environment. You may choose from the following options: z z z z z z z Disable Load Balance Failover Balance-XOR 802.3ad Balance-TLB Balance-ALB See the right diagram for details.
Appendix A: Product Specifications Hardware Specifications Item Spec LAN Interface RJ-45x2 : 10/100/1000 BASE-TX Auto MDI/MDI-X OLED indicator HDD1 Power, Activity/Fail HDD2 Power, Activity/Fail HDD3 Power, Activity/Fail HDD4 Power, Activity/Fail WAN (Activity) LAN (Activity) USB Busy USB Failure OLED module 2.8” (256x64 dots) Blue color, 84x25.
Software Specifications Network File Protocols Authentication Network Client Type Network Configuration Disk Management RAID iSCSI Target Folder Management Quota Management Backup System Management Event Notification UPS Support Printer Server Supported USB Devices Setup Utility Microsoft Networks (CIFS/SMB) Apple Filing Protocol (AFP 3.
MAC OS X *AD support: Works as a client member in a Microsoft Active Directory domain, allowing the N4200 to utilize the domain users and groups setting for authentication to the system and authorization to the share folders. **For supported USB dongles, please contact sales@thecus.
Appendix B: Customer Support If your N4200 is not working properly, we encourage you to check out Chapter 7: Troubleshooting, located in this manual. You can also try to ensure that you are using the latest firmware version for your N4200. Thecus is committed to providing free firmware upgrades to our customers. Our newest firmware is available on our Download Center: http://www.thecus.com/download.
Appendix C: RAID Basics Overview A Redundant Array of Independent Disks (RAID) is an array of several hard disks that provide data security and high performance. A RAID system accesses several hard disks simultaneously, which improves I/O performance over a single hard disk. Data security is enhanced by a RAID, since data loss due to a hard disk failure is minimized by regenerating redundant data from the other RAID hard disks.
RAID 5 RAID 5 offers data security and it is best suited for networks that perform many small I/O transactions at the same time, as well as applications that require data security such as office automation and online customer service. Use it also for applications with high read requests but low write requests. RAID 5 includes disk striping at the byte level and parity information is written to several hard disk drives.
Disk Usage When all 7 disks are of the same size, and used in RAID, N4200 disk usage percentage is listed below: RAID Level Percentage Used RAID 0 100% RAID 1 1/n x 100% RAID 5 (n-1)/n x 100% RAID 6 (n-2)/n x 100% RAID 10 50% JBOD 100% n：HDD number 140
Appendix D: Active Directory Basics Overview With Windows 2000, Microsoft introduced Active Directory (ADS), which is a large database/information store. Prior to Active Directory the Windows OS could not store additional information in its domain database. Active Directory also solved the problem of locating resources; which previously relied on Network Neighborhood, and was slow. Managing users and groups were among other issues Active Directory solved.
Appendix E: UPS Compatibility List Brand Series Ablerex MS-RT ActivePower 1400VA AEC Model MiniGuard UPS 700 M2501 cable Back-UPS Pro Matrix-UPS Smart-UPS APC Back-UPS 940-0095A/C cables, 940-0020B/C cables, 940-0023A cable Back-UPS Office 940-0119A cable Masterswitch Not a UPS - 940-0020 cable Back-UPS RS 500 custom non-USB cable Regulator Pro serial Belkin Resource Home Office F6H350-SER, F6H500-SER, F6H650-SER Universal UPS F6C800-UNV, F6C120-UNV, F6C1100-UNV, F6H500ukUNV Fortress (new
Brand Fideltronik Fiskars Series Model Notes Ares 700 and larger Other Ares models PowerRite MAX PowerServer 10, 30 All models with alarm interface MP110/210 Gamatronic MS-T MS µPS3/1 Gemini HP UPS625/UPS1000 R3000 XR R5500 XR INELT Monolith 1000LT Infosec iPEL Ippon (various) Liebert Masterguard UPStation GXT2 contact-closure cable (various) HF Line 1..4 boards, /2 5..
Brand Series Oneac EG/ON Series advanced interface Online P-Series OnLite AQUA 50 Orvaldi Model various not 400 or 600 SMK-800A Powercom Powercom ULT-1000 TrustTrust 425/625 BNT-1000AP Advice Partner/King Pr750 BNT-2000AP PowerGuard PG-600 PowerKinetics 9001 PowerTech Power Walker Comp1000 DTR cable power Line-Interactive VI1000 3110, 3115, 5119, 5125, 5119 RM, PW5115 Powerware Powerwell PW5125PW9120, PW9125, 9120, 9150, 9305 PM525A/-625A/-800A/-1000A/-1250A RPF525/625/800/1000 Repotec
NOTE • The UPSes marked Blue have been tested and work well • If your UPS is not in the support list, be sure that the UPS supports one of following protocols: o SEC protocol o Generic RUPS model o Generic RUPS 2000 (Megatec M2501 cable) o PhoenixTec protocol o Safenet software 145
Appendix F: Licensing Information Overview This product included copyrighted third-party software licensed under the terms of GNU General Public License. Please see THE GNU General Public License for extra terms and conditions of this license. Source Code Availability Thecus Technology Corp. has exposed the full source code of the GPL licensed software. For more information on how you can obtain our source code, please visit our web site, http://www.thecus.com.
CGIC License Terms Basic License CGIC, copyright 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 by Thomas Boutell and Boutell.Com, Inc. Permission is granted to use CGIC in any application, commercial or noncommercial, at no cost. HOWEVER, this copyright paragraph must appear on a "credits" page accessible in the public online and offline documentation of the program.
they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 5.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
