CONTENTS SAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 CONNECTING WITH EXTERNAL EQUIPMENT 6 RESOLUTION 7 CONTROLS AND FUNCTIONS 8 REAR VIEW 13 D-SUB CONNECTOR PIN ASSIGNMENTS 14 POWER MANAGEMENT 15 SPECIFICATIONS 16 TROUBLESHOOTING GUIDE 17 WICHTIGE HINWEISE (GERMAN) 18 This Monitor was Manufactured by ISO 9001 Certified Factory 1 INSTRUCTION MANUAL
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 7.
SAFETY INSTRUCTION 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the Product does not operate normally when the operating instructions are followed.
CAUTIONS NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases. KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising.
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONNECTING WITH EXTERNAL EQUIPMENT CAUTION Be sure to turn off the power of your computer before connecting the monitor. 1. CONNECT THE VIDEO SIGNAL CABLE A. Connect one end of the signal cable to the back panel of the monitor and connect the other end to the graphic card on back of the computer. B. Secure the connection with the screws on the plug. 2. CONNECT THE POWER CORD A. Connect the plug of the AC/DC adaptor to the monitor. B.
RESOLUTION This monitor is a digitally-controlled multi-frequency monitor. It operates at horizontal frequencies of 31 to 60KHz and vertical frequencies of 56 to 75Hz. Because of its micro processor-based designs it offers auto-synchronization and auto-sizing capabilities. This monitor offers 6 programmed settings as listed in the table below. And designs its best quality at 1024X768, 48KHz@60Hz.
CONTROLS AND FUNCTIONS B. MENU BUTTON C. AUTO D. SELECT BUTTON POWER INDICATOR(LED) A. POWER SWITCH E. ADJUST BUTTONS (LEFT & RIGHT) A. POWER ON/OFF( ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes out. B. MENU Activates and exits the On Screen Display. Auto Adjust Screen : Brightness, Contrast, H.
CONTROLS AND FUNCTIONS D. SELECT( ) The select button allows user to activate the desired adjustment with changing the adjustment bar to green. E. ADJUST ( , ) The Adjust button allows user to choose the icons (controls) in the menu. Pressing the adjust button or will step through all available adjustment icons (controls).
CONTROLS AND FUNCTIONS Screen Adjusts the Brightness, Contrast, H. Position, V. Position, Phase and Frequency of the Screen. Brightness Increases( ) or decreases( ) the intensity(illumination) of the image. Contrast Increases( ) or decreases( ) the strength(lightness or dimness) of the image. H. Position Moves images to left( ) or right( ). V. Position Moves images to up( ) or down( ). Phase Adjust As removing horizontal noise, adjusts the focus of the screen’s image.
CONTROLS AND FUNCTIONS Color Adjusts the Color Temperature, Red, Green, Blue of the Screen. Color Temp Adjusts color temperature to 9300K, 6500K, custom color mode. (9300K is Factory default data) Red Increases or Decrease the strength of the Red. Green Increases or Decrease the strength of the Green. Blue Increases or Decrease the strength of the Blue. Utility Extra Functions. (Recall, Full Auto) Recall Resets the control functions back to the original factory preset values.
CONTROLS AND FUNCTIONS Language Selects a language among English, Francais, Deutsch, Espanol, . OSD Adjusts the OSD Timeout, OSD H. Position, OSD V. Position and Transparency of the OSD OSD Timeout Adjusts the OSD display timing. Increase or Decrease the display time of the OSD. OSD H. Position Moves the OSD position to left/right. OSD V. Position Moves the OSD position to up/down. OSD Transparency Increase or Decrease the display Transparency of the OSD. Exit Exit user menu.
REAR VIEW F. DC JACK AC/DC adaptor connection. G. D-SUB CONNECTOR Connect to the video signal cable. F. DC JACK G. D-SUB CONNECTOR AC/DC ADAPTOR 1 2 1 GROUND 2 DC+12V out ACCESSORY 1. POWER CORD 2. USE’R MANUAL 3. AC/DC ADAPTOR 4.
D-SUB CONNECTOR PIN ASSIGNMENTS PIN ASSIGNMENTS Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA(for DDC) 5 GROUND 13 H-SYNC.(or H+V SYNC.) 6 RED GROUND 14 V-SYNC.
POWER MANAGEMENT This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.
SPECIFICATIONS LCD Type 15.0 Diagonal AM-TFT(Active-Matrix) DOT PITCH: 0.297mm BRIGHTNESS: 250cd/ (Typical) CONTRAST RATIO: 300:1(Typical) RESPONSE TIME: 25 msec(Typical) RESOLUTION(H x V) 1024X768 @60Hz FREQUENCY HORIZONTAL: 31-60KHz VERTICAL: 56-75Hz VIDEO DOT RATE 80MHz INPUT SIGNAL VIDEO(Analog 0.
TROUBLESHOOTING GUIDE TROUBLE No image on display screen TROUBLESHOOTING TIP 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip. 2. Power switch should be in the ON position and LED is lit. 3. Check that the Brightness and/or the Contrast adjustments of the Display have not been turned down to minimum levels. “Check Input Signal” message on screen 1. The signal cable should be completely connected to the video card/computer. 2.
FOR GERMAN WICHTIGE HINWEISE Achten Sie darauf, da das Gerät nur in eine AC100-240V(DC12V) SchukoSteckdose eingesteckt wird. Die Steckdose sollte jederzeit frei zugänglich sein, um bei einem evtl. auftretenden Notfall das Gerät schnell von der Stromversorgung zu trennen. Achten Sie desweiteren darauf, da die Netzanschlu leitung nicht mechanisch beansprucht noch sonstwie beschädigt wird. Öffnen Sie niemals das Gerät! Im Inneren befinden sich Teile mit gefährlicher Spannung.
