7" TFT LCD Monitor MODEL No.
CONTENTS SAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 CONNECTING WITH EXTERNAL EQUIPMENT 6 RESOLUTION 8 CONTROLS AND FUNCTIONS 9 REMOTE FUNCTIONS 19 REAR VIEW 21 STAND SLOPE 22 D-SUB CONNECTOR PIN ASSIGNMENTS 23 POWER MANAGEMENT 24 SPECIFICATIONS 25 TROUBLESHOOTING GUIDE 26 WICHTIGE HINWEISE (GERMAN) 27 This Monitor was Manufactured by ISO 9001 Certified Factory 1 INSTRUCTION MANUAL
SAFETY INSTRUCTION 1. Read all of these instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product. 7.
SAFETY INSTRUCTION 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the Product does not operate normally when the operating instructions are followed.
CAUTIONS NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases. KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising.
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CONNECTING WITH EXTERNAL EQUIPMENT CAUTION Be sure to turn off the power of your computer before connecting the monitor. 1. CONNECT THE VIDEO SIGNAL CABLE A. Connect one end of the signal cable to the back panel of the monitor and connect the other end to the graphic card on back of the computer. B. Secure the connection with the screws on the plug. 2. CONNECT THE POWER CORD Connect the female end of the power cord to the power input receptacle on the LCD Monitor.
CONNECTING WITH EXTERNAL EQUIPMENT 5. CONNECT THE TUNER(OPTION) INSTRUCTION Be sure to turn off the power of your monitor before connecting the tuner. A. Open the cover. B. Insert the Tuner and close the cover. CAUTION A. Do not disassemble the tuner after proper Installation. B. Do not pull the antenna terminal only. This terminal is easy to break.
RESOLUTION This monitor is a digitally-controlled multi-frequency monitor. It operates at horizontal frequencies of 31 to 80KHz and vertical frequencies of 56 to 75Hz. Because of its micro processor-based designs, it offers auto-synchronization and auto-sizing capabilities. This monitor offers 11 programmed settings as listed in the table below and designed its best quality at 1280X1024, 64KHz@60Hz.
CONTROLS AND FUNCTIONS B. SOURCE BUTTON C. MENU BUTTON D. CHANNEL BUTTONS (DOWN & UP) E. VOLUME BUTTONS (LEFT & RIGHT) REMOCON SENSOR POWER INDICATOR(LED) A. POWER SWITCH A. POWER ON/OFF( ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights with green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes Red. B.
CONTROLS AND FUNCTIONS D. CHANNEL( CH: ) Increases or decreases the channel number. (In PC mode, down key operates as “Auto adjust”) This button allows user to enter the sub-menu of the activated function when down key is pressed on the main menu. E. VOLUME( VOL: ) Adjust the volume / Adjust menu settings. 1. SELF-TEST DISPLAY When there is no connection at PC, the On Screen Display will show for 3 seconds. Check input Signal 2.
CONTROLS AND FUNCTIONS : Screen : Brightness Increase or decrease the intensity of the image. : Contrast Increase or decrease the intensity(lightness or dimness) of the image. : H. position (PC Mode Only) Move image horizontally on screen right or left. : V. position (PC Mode Only) Move image vertically on screen up or down. : Clock (PC Mode Only) Adjust the vertical noise of screen image. : Phase (PC Mode Only) Adjust the number of horizontal picture elements.
CONTROLS AND FUNCTIONS : Audio : Volume Adjust audio volume. : Equalizer (Loudspeaker Only) Boost / Cut specific frequency or compensate for frequency distortion of the sound. Select preferred Sound setting: mode 1~4 and Adjust the level of the Sound frequency in user mode. : Balance(Loudspeaker Only) Adjust the balance of left and right speaker sound. : Loudness (Loudspeaker Only) Compensate the sound to consider the frequency sensitivity of human ear.
CONTROLS AND FUNCTIONS : OSD : H. Position Move the OSD position to right( ) or left( ). : V. Position Move the OSD position to up( ) or down( ). : Transparency Select the OSD background. : OSD Timer Select the OSD display timing. : Language Select a language among English, Français, Deutsch, Español, Danish.
CONTROLS AND FUNCTIONS : Color (PC Mode) : Color Temp Adjust color temperature to 9300, 6500, user. (note : 9300 is factory default) : Red Adjust red color for user. : Green Adjust green color for user. : Blue Adjust blue color for user.
CONTROLS AND FUNCTIONS : Utility : Recall Select to reset all setting to the factory default values. : Full Auto (PC Mode Only) Auto geometry and color adjustment. : Caption (NTSC Only) Enable or disable closed caption feature(CC1, CC2, CC3, CC4). : Vchip (NTSC, US Only) Initial passwords is “0000”. The V-chip can block certain rated television shows off (if chosen) so children cannot watch programs that parents do not approve.
CONTROLS AND FUNCTIONS 1) TV Guidelines off : Not Rated TV-Y : Young Children TV-Y7 : Children 7 and over TV-G : General Audience TV-PG : Parent Guidance TV-14 : Viewer 14 and over TV-MA : Mature Audience (FV : Fantasy Violence V : Violence S : Sexual Situation L : Coarse Language D : Suggestive Dialog) 2) MPAA Rating (Motion Picture Association of America [Movie rating organization]) off : Not Rated G : General Guidance PG : Parental Guidance Suggested PG-13 : Parents Strongly Cautioned R : Restricted Unde
CONTROLS AND FUNCTIONS : TV Channel (Program) This menu is possible to select, Input Source must be set ‘TV’. : Auto Search Find available channels(Program) and save automatically. : Fine Tuning Adjust a mismatch between real and programmed channel(Program). : Store / Clear Select “Store” to save the channel(Program) or select “Clear” to remove the channel(Program). : TV Type (NTSC Only) Select Air or Cable TV system.
CONTROLS AND FUNCTIONS : Exit : Exit Turn off OSD Menu.
REMOTE FUNCTIONS F. REMOTE CONTROLLER 1 2 21 4 3 8 5 6 9 7 10 6 7 11 12~19 20 1. POWER( ) Turns the power ON or OFF. There will be a few seconds delay before the display appears. 2. SOURCE Select pc or video(TV / Video / S-Video / SCART) sources. 3. MUTE Mute the sound. 4. AUTOSCAN Find available channels(program). 5. MENU Activates and exits the On Screen Display. 6. VOL( ) Increases or decreases the level of audio volume. 7. CH( ) Increases or decreases the channel number.
REMOTE FUNCTIONS 8. DISPLAY Channel display in TV Source. 9. TV Change Input Source to TV. 10. AUTO Auto geometry adjustment in PC Source. 11. EXIT Exit the on Screen Display. 12. TEXT ( ) Select Teletext display / Return to TV picture display. 13. INDEX ( ) Return to index page in teletext mode. 14. CANCEL( ) Display the TV picture on the screen while waiting for the new teletext page. 15. REVEAL( ) Reveal hidden text, such as Solutions of riddles or puzzles in teletext mode. 16.
REAR VIEW G. AC INLET Power cord connection. NOTE: Power cord is used as main power disconnect device in this product. H. D-SUB CONNECTOR Connect to the video signal cable. G. AC INLET H. D-SUB CONNECTOR ACCESSORY 1. POWER CORD 2. REMOCON 3. USER’S MANUAL 4. A/V CABLES(Option) 5.
STAND SLOPE TORQUE BY POSITION Recommend that the slope from 0 to 20 degree. In case of the degree is more than 20, please refer below sheet.
D-SUB CONNECTOR PIN ASSIGNMENTS PIN ASSIGNMENTS Pin 1 RED VIDEO 9 2 GREEN VIDEO 10 SIGNAL CABLE DETECT 3 BLUE VIDEO 11 GROUND 4 GROUND 12 SDA(for DDC) 5 GROUND 13 H-SYNC.(or H+V SYNC.) 6 RED GROUND 14 V-SYNC.
POWER MANAGEMENT This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system.
SPECIFICATIONS LCD Type 17.0 Diagonal AM-TFT(Active-Matrix) DOT PITCH: 0.264mm BRIGHTNESS: 250cd/ (Typical) CONTRAST RATIO: 350:1(Typical) RESPONSE TIME: Tr -5msec, Tf-20msec(Typical) RESOLUTION(H x V) 1280X1024 @60Hz FREQUENCY HORIZONTAL: 31-80KHz VERTICAL: 56-75Hz INPUT SIGNAL VIDEO(Analog 0.
TROUBLESHOOTING GUIDE TROUBLE No image on display screen TROUBLESHOOTING TIP 1. Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip. 2. Power switch should be in the ON position and LED is lit. 3. Check that the Brightness and/or the Contrast adjustments of the Display have not been turned down to minimum levels. “Check Input Signal” message on screen 1. The signal cable should be completely connected to the video card/computer. 2.
