WISR Installation manual No. IM0973670 A 02 Art. No: 0300100 02/2019 English Art. No.
Installation manual WISR, Art. No. 0300100 Safety In order to guarantee safe operation, these safety instructions must be read before you start using this equipment. • Do not open the enclosure. This can cause damage, shortcircuiting or electrical shocks. • Do not expose the equipment to extreme temperatures, this can cause deformation of the enclosure or damage to internal components. • Repairs may only be undertaken by Orlaco. • The equipment must be assembled as shown in this manual.
Installation manual Contents 1. Introduction 2. Configuration 3. Operation 4. Assembly/Installation 4.1. Options 4.2. Connections 4.3. The photonView app 5. Dimensions 6. Technical specifications 7. Electrical connections 8. Maintenance and cleaning 9. FCC Statement 10. IC Statement 11. Disposal 12. General terms and conditions 13. Release notes Page 3 5 5 5 5 5 5 6 6 7 8 8 8 9 9 10 1. Introduction The WISR sytem provides a Wi-Fi® connection within a view system.
Installation manual Application possibilities of the WISR system, figure. 1.
Installation manual 42,9 2. Configuration 178,8 38 37 To create a Wi-Fi® connection, there must always be a WISR router in the system. In a 2 camera system, one WISR router is connected with the tablet. For the 4 camera 12 system a second WISR router set communicates with the other WISR router within a work zone. Figure 1 shows two systems using one or two WISRs. To connect two cameras with the WISR, an extension cable must be used; This cable must be ordered separately, check with Orlaco.
Installation manual 4.3 The photonView app The detailed user instructions are listed in the User Manual UM0972260. 76,3 101,6 10RXX/XX*XXXX RATED VOLTAGE 9 - 32 Vdc Article no: XXXXXXX Serial no. XXXXXXX RATED POWER MAX 5W FCC ID: XXX-XXX IC ID: XXXXXA-XXX TDK: PR1A91DA1 IP69K Power Video 1 5. Dimensions 139 Made in the Netherlands Video 2 ∅7,4 2x 4.2 Connections Connecting the WISR system is easy. Connect the tablet to the WISR router and the Cameras using the PhotonView app.
E AG LT VO D dc ER TE V O W RA /24 P 12 TED W 5 R A AX M 130,3 in e th Video 2 e ad Video 1 Ne ds an IC : P K K TD 69 IP erl th er w Po o de Vi Installation manual M Power 139 Made in the Netherlands 1 o de Vi ∅7,4 2x Power Connector 8p maleVideo Power 101,6 1 Video 2 76,3 42,4 Video 1, 2 Connector139 4p female 139 Video 1 Video 2 Un Protection cap 42,4 130,3 cable 2m m8F M12 Power Art. no.
Installation manual 8. Maintenance and cleaning Clean this product with a damp cloth. Do not use aggressive chemicals or abrasive cleaning agents. 9. FCC Statement §15.21 Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Either (§15.105) class B device The equipment has been tested and found comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Installation manual (Français) Pour se conformer aux exigences de conformité CNR 102 RF exposition, pour des configurations mobiles, une distance de séparation d’au moins 20 cm doit être maintenue entre l’antenne de cet appareil et toutes les personnes. Cet appareil ne doit pas être colocalisés ou fonctionnant en conjonction avec une autre antenne ou transmetteur. 11. Disposal Disassembly, removal and disposal.
Installation manual 10 IM0973670 A 02
Installation manual IM0973670 A 02 11
ORLACO Orlaco is a Manufacturing company that specializes in making cameras and monitor systems for commercial vehicles, fork-lift trucks, cranes, off shore and maritime. Our objective is to design and produce camera systems for the professional market that improve the drivers’ view and increase operating efficiency. At our facility in Barneveld we locate our design, manufacturing, warehousing and service department. Vision is our mission®.