翔鑫科技股份有限公司 Oro Technology Co.
ORO TPMS User Manual To ensure correct operations and services please read these instructions before installing and operating the TPMS Table of Contents 1. Notice…………………………………………………….....……….……………1 2. W410 Tire Pressure Monitoring System……………...………...…..……….2 3. W410 TPMS Specification……………………..…….……………...…………2 5. W410 TPMS Installation…….…………………………………………..………3 Display Unit Installation……………………..…………………………………..3 Tire Sensor Installation………..….…………………………….…………........4 6. W410 System Operation…….………...
■FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
■Reacting to Alerts When an alert or warning is received, reduce vehicle’s speed and proceed to a safe location to stop where the tire can be inspected and /or serviced. The low-pressure alert indicates that the air pressure has dropped to a selected minimum while a high-temperature alert indicates that the temperature of the tire content has surpassed the threshold value set.
W410 Tire Pressure Monitoring System ORO-W410 Tire Pressure Monitoring Systems (TPMS), can monitor and provide tire pressure, tire temperature, and car battery information in real time. This real time information can extend tire life, reduce fuel consumption, help monitor battery status, and provide a more safe driving condition. ORO-W410 Tire Pressure Monitoring System includes 4 tire sensors, and1 receiver display.
W410 TPMS Installation 1. Please enter the default set mode before installation to set up required Tire Pressure value for the vehicle. The default pressure value of W410 is 35psi (2.4bar). The warning system will alarm when the tire pressure is higher or lower than 25% of set up Tire Pressure value. 2. The tire temperature will rise simultaneously with Tire Pressure in normal driving conditions. In cold weather conditions such as 6℃ (10℉) the tire pressure may drop 1psi or more.
Screw If the user wants to connect the power directly, please visit an electrical auto shop, dismantle the cigar plug and solder the red and green cable to the AC power. The black and white cables are for grounding. 4.
Once TPMS is installed correctly, turn on the ignition to start monitoring the tire pressure/temperature and voltage. WARNING: The tire sensor will transmit a signal when the vehicle speed is over 20km/hr and will stop transmitting a signal when the vehicle has stopped for over 5 minutes. If the tire pressure is lower than 18psi, the tire sensor will transmit abnormal signal continuously to the user. There are 2 types for model W410, General Type and Power Saving Type. a.
2. Operation to Change Display Mode W410 has 3 different modes. They are Tire Pressure Display Mode, Temperature Display Mode, and Pressure-Temperature Alternate Mode. The display will show the tire pressure mode once it is turned on. To enter the temperature mode press the MODE button once and to display pressure-temperature press it another time.
Set up Rear Tire Pressure Value: Range: 24psi~80psi (1.7bar~5.5bar), the default set value is 35psi (2.4bar) a. Press the SET button for 3 seconds to enter the Rear Tire-Standard Tire Pressure Setting Mode. The unit increases by 1 psi with each press of the button. When it has reached 80psi (5.5bar), pressing the button again will return the system unit to 24 psi (1.7bar). b. The system will enter to High Temperature Alarm Value Mode automatically by quickly pressing the SET button.
Pressure mode display Temperature mode display Rotate Displaying Pressure & Temperature c. After quickly Pressing the SET button to TURN ON the device successfully, the system will enter AUTO Display TURN OFF Timing Set Mode automatically. AUTO Display TURN OFF Timing Set Mode︰There are 4 modes to select: Normal ON, 1 minute display, 3 minutes display and 5 minutes display. a. Quickly Press MODE button to select the AUTO TURN OFF Timing Mode.
Tire Temperature High Alarm Mode︰When the tire temperature is higher than set value. Warning Method：The abnormal tire will flash RED with Beep sound as warning. Rapid Pressure Air Leaking Alarm Mode︰When the tire has a rapid pressure air leaking situation. (Vary more than 3psi or 20kPa in 30sec.) Warning Method：The abnormal tire will flash RED with Beep sound as warning. Battery Low Voltage Alarm Mode︰When battery voltage is lower than 11.5V. (Regardless the vehicle engine is operating or not.
Warning Mode：Show E1 and Greed Light does not work. No Signal Detecting Alarm Mode︰When receiver module is not able to receive signal from tire sensor over 10 minutes. Warning Mode：Show E2 on the display without Green Light. NOTE：1. When the alarm beep sound happens, pressing the MODE key continuously for 3 second will turn off the audible alarm. 2. When there is an abnormal status in the receiver module and the unit is not able to receive signals from tire sensor, please contact customer service.
Rear Tires Exchange) then the system will return to the normal operating display. Mode 1: Front and Rear Tire Parallel Exchange Mode 2: Tire Diagonal Exchanged Mode 3：Front Tire Diagonal Exchange, Rear Tire Parallel Exchange to Front Mode 4: Rear Tire Diagonal Exchange, Front Tire Parallel Exchange to Rear Mode 5: Right Side and Left Side Tire Parallel Exchange Mode 6: Random Repositioning The user should install the tire to their desired position before entering mode 6.
display shows a yellow “6”, this means that it is now in mode 6. Reset starting from Right Front Tire -> Right Rear Tire -> Left Rear Tire -> Left Front Tire automatically in order to complete the set up mode 6. The user should deflate the tire pressure rapidly over 0.3bar/30kPa or 4 psi within 15 sec. until there is a beep sound, which means the user has completed the set up a. Depress the SET key to skip LF relearn or after completing the rapid deflation of Left Front tire for relearn process.
Product Warranty Policy We warrant our products for 12 months from the date of original purchase to be free from defects in materials and workmanship. If, during this period, the product fails under normal usage, because of a manufacturing defect, we will replace or repair the item. To obtain repair or replacement under the terms of this warranty, please return the product to the place of purchase. Proof of purchase and date of purchase are required to validate the warranty claim.
ORO Technology thanks you for your using ORO TPMS and wishes you “Safe Driving.” Appendix bar Tire pressure unit, 1 bar = 0.1N / mm2 psi Tire pressure unit, 1 psi = 0.0689 bar. kPa Tire pressure unit, 1 kPa = 0.
