Installation and Safety Intructions

ManualsBrandsOrren Ellis ManualsCeiling LightsKeli 4 - Light Kitchen Island Linear LED Pendant

INSTALLATION AND SAFETY INSTRUCTIONS

Warning:

Read instructions carefully. If you are unclear as to how to

proceed, consult a qualified electrician. NOTE: Proper wiring is

essential for the safe operation of this fixture.

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture.

FIXTURE ASSEMBLY

Carefully removed the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

INSTALLATION

STEP 1: Connect the stem （A）together and install it into lamp

body.

IMPORTANT: Do not attach fixture directly to outlet

box.

GROUNDING INSTRUCTIONS

STEP 1:Mount ground wire on mounting bar onto ground screw

in the outlet box . Firmly connect the mains supply wires to the

light fitting using the connectors(D) provided . Ensure that wires

are secure and that no bare wire is exposed.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and connect

the wires according to the directions below:

GROUP A: Connect to Black

GROUP B: Connect

to White

House Wire

BLACK

WHITE

*PARALLEL WIRE (round &

*PARALLEL WIRE (square &

smooth)

ridged)

WHITE

OR GREY

WITH

WHITE OR GREY WITHOUT

TRACER

BROWN

GOLD OR

BLACK

BROWN, GOLD OR

BLACK

WITHOUT TRACER

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracerwire is

square shaped or ridged and the less tracer wire is round in shape or

smooth (seen best when viewed from wire end.)

STEP 2: Loosen the decorative nut(B)，and take out the mounting

bar.

STEP 3: Firmly connect the mains supply wires to the

driver wire fitting using the quickly connector(C)

STEP 4: Install the mounting bar onto the ceiling , then fix it

tightly using the screw(D)

STEP 5: Firmly connect the main supply wires to the ground

wire fitting using the connectors(E) provided . Ensure that

wires are secure and that no bare wire is exposed.

STEP 6:Install the whole lamp onto the canopy , then using

the decorative nut (F) screw it tightly

CLEANING

To clean, wipe fixture with a soft and dry cloth. Do not use

abrasive materials such as scouring pads or powders, steel

wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to

order replacement parts. All parts for this fixture can be ordered

from place of purchase. Be sure to use exact wording from

illustration when ordering parts.

Line art shown may not exactly match the fixture enclosed.

However, the installations do apply to this fixture.

Summary of content (1 pages)

PAGE 1
INSTALLATION AND SAFETY INSTRUCTIONS Warning: Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture. FOR YOUR SAFETY STEP 4: Install the mounting bar onto the ceiling , then fix it tightly using the screw(D) STEP 5: Firmly connect the main supply wires to the ground wire fitting using the connectors(E) provided . Ensure that wires are secure and that no bare wire is exposed.