Installation & Assembly
Hardware Contents
AA
Crossbar
x1
Package Contents
B
A
C
D
Lock Screw
x4
Rubber Washer
x4
Fixture Body
x1
Glass Panel
with Crystals
x1
BB
CC
DD
Nipple
x1
Lock Washer
x1
Hex Nut
x1
Lock Knob
x1
EE
STEP 1 Install Crossbar and Nipple-
A. Secure the Crossbar (AA) to the
Outlet Box with Outlet Box Screws
(not supplied) Tighten until snug.
* Pliers is required on this step.
.
B. Thread the Hex Nut (DD) onto one end
of the Nipple (BB). Place the Lock
Washer (CC) over the Hex Nut end of
the Nipple (BB) and then thread the
Nipple (BB) into the center lock hole of
the Crossbar (AA). Using pliers,
thread the Hex Nut (DD) against the
Crossbar (AA) and hand tighten until
snug.
Figure 1
(Step 2 Continued)
adjust the length of the Nipple (BB) on the Crossbar (AA) by
unscrewing the Hex Nut (DD) and the Lock Washer (CC) and then
screwing the Nipple (BB) in or out of the Crossbar (AA) until the
correct length is achieved. Once the Fixture Body (A) is secure,
remove the Lock Knob (EE) and Fixture Body (A) and proceed to
step 3.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Figure 3
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into
the outlet box and position
the Fixture Body (A) over the
outlet box. Attach the Fixture
Body (A) over the Nipple (BB)
and secure with the Lock
Knob (EE). Hand tighten until
snug.
STEP 5 Install Glass Panel with Crystals-
A. Place the Glass Panel with Crystals (D) onto the Fixture Body (A)
with Crystals towards the Fixture Body (A). Secure by threading
Rubber Washers (B) and Lock Screws (C) into Couplings inside of
the Fixture Body (A). Hand tighten until snug.
Your fixture is now assembled and ready to use. Enjoy!
Integrated17WLED
:LutronDVELV-300PorLutronSELV-300P.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
AA
Outlet
Box
Outlet Box
Screws (not
supplied)
CC
DD
BB
STEP 2 Test Fitting Fixture
Body to Nipple
-
A. Fit the Fixture Body (A) over
the Nipple (BB) on the
Crossbar (AA) and secure
with the Lock Knob (EE). The
Fixture Body (A) should be
snug against the ceiling and
the Lock Knob (EE). If not,
BB
Outlet Box
EE
A
Figure 2
Lock Washer
and Hex Nut
BB
Outlet Box
EE
A
Figure 4
Coupling
D
B
C
Figure 5
A
Assembly Instruction
ToolsRequired:
LightSource:
CompatibleDimmerSwitches
EstimatedAssemblyTime:
Preparation:
Gotothe Care+Maintenance selection.
Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
1of2