READ THESE INSTRUCTIONS AND AND SAVE THEM FOR FUTURE USE Installation Guide Table of Contents: Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. pgs. 4 - 5 Wiring. pg. 6 Canopy Assembly. pg. 7 Blade Assembly. pg. 7 Light Kit Assembly. pgs. 7 - 8 Wall Control Operation. pg. 8 Testing Your Fan. pg. 8 Troubleshooting. pg. 9 Parts Replacement. pg. 9 Warranty. pg.
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. 1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges. 2.
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory. a b c d e f g h i a. canopy. 1 piece b. weatherproof hanging ball cover. 1 piece c. hanging bracket. 1 piece d. yoke cover. 1 piece e. 6in.
3. Installation Preparation. To prevent personal injury and damage, ensure that the hanging location allows the blades a clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square feet (37.2 square meters). 12ft. - 20ft. (3.66m - 6.1m) blade edge 30 7 feet inches (2.13 m) (76 cm) 12ft. - 20ft. (3.66m - 6.1m) downrod installation This fan can be mounted with a downrod on a regular (no-slope) or vaulted ceiling.
. Fan Assembly. Remove hanging ball from downrod provided by loosening set screw on hanging ball. Remove pin and clip. Lower hanging ball and remove stop pin. Then slide hanging ball off downrod. [Refer to diagram 1.] Loosen yoke set screws and nut at top of motor housing. [Refer to diagram 2.
5. Fan Assembly. (cont.) Thread safety cable and wires through hanging ball; then, slide hanging ball over downrod--the top of the downrod should be noted as having a set screw hole; use this hole when setting the set screw. Insert stop pin into top of downrod and raise hanging ball. Be sure stop pin aligns with slots on the inside of the hanging ball. Tighten set screw securely. [Refer to diagram 4.
6. Wiring. white supply wire WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure switch is turned to the OFF position. black supply wire CAUTION: Be sure outlet box is properly grounded and that a ground wire (GREEN or Bare) is present. from ceiling wire connector black white Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code.
7. Canopy Assembly. hanging bracket Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy over loosened screw in hanging bracket and push up. Twist canopy to lock. Re-insert screw that was removed and then tighten both screws securely. screw canopy screw 8. Blade Assembly.
motor housing 9. Light Kit Assembly. (cont.) Connect WHITE wire from motor housing to WHITE wire from light kit fitter. Connect BLACK (or BLUE) wire from motor housing to BLACK wire from light kit fitter. Be sure molex connections snap together securely. molex connections Remove 1 screw from underside of fitter plate and partially loosen the other 2 screws. fitter plate light kit fitter Carefully arrange wiring within fitter plate.
Troubleshooting. Warranty. WARNING: Failure to disconnect power supply prior to troubleshooting any wiring issues may result in serious injury. LIFETIME LIMITED WARRANTY: We warrant this fan to the original household purchaser for indoor use under the following provisions: 1-YEAR WARRANTY: We will replace or repair any fan which has faulty performance due to a defect in material or workmanship. Contact our Customer Service to arrange for return of fan. Return fan, shipping prepaid, to us.