Installation & Assembly

ManualsBrandsOrren Ellis ManualsCeiling LightsSafira 1 - Light Single Cylinder Pendant

READ

AND SAVE

THIS

INSTRUCTION

SHEET

(t)

arrrNrroN

1.1

To ensure

the

success

of the installation,

sure to

read

these

instructious

and

review the diagrams

thoroughly

before beginning.

t.2

All

electrical

connections

musl be

iu accord.ance

wilh local

codes.

ordinanses,

the

National

Electrical

Code. If

you

are unfamiljar

with

the

methods

of installing

electrical wiring, secure

the servlces

of a

qualified

licensed

electrician.

1.3

These

fixtures are

intended

to be

burlding mounted

and must

supported

by the building

structure.

1.4

Do not operate

lhe f-ighting

fixture clcse to

any combustible

material.

1.5

Ensure

that the

fitting

is cool

and sritched

off before

changing

the bulb.

1.6

not use

bulbs exceeding

maximum wattage

marked. on

lighting fixture.

(2)

caurtox

BEFoF,E

INSTALLATIOI,T

2.1 Prepare

tools aud

materials

required,

e.g.: Ladder,

Hrench,

ffire

cul:er,

Screw driver,

Bulbs

and Wiring

supliies

required

by eleetrical

code

?,2

Bef.ore

starting the

installation,

dlsconnect the

power

opening

the

circuit

breaker or by

rer:noving

the

fuse at

the

fuse

box. Turning

the

power

off

using the

light sfitch is

noL sufficient

prevent

electrical shoek.

2.3

you

are

replacing an exrs*.rng

fixture, disconnect and

remove the

old

fixture.Expose

the

supply

rr1rulg.

2.4

llo

rough or

sharp edges

are

in contact

*ilh

any

of the wire

lo ensure

the i-nsulation

on any

of lhe rires

has nol been damaged

during

installation.

2,5

ffre

bare or

green

insulated wire

are for

grounding,

do not

connect with

current carrying

wires.

2.6

Firstly connect

white

(or

rough)

fixture

wire with

white

suppiy

wire

and

then

eonnect

black

(or

smooth) fixture wire

with black supply wire.

after

fixture wires

are connected

with

supplier

wrres,

lhe bare

parts

of wires

need to

be completely

covered

conneetor,

prevent

from causing

short circuit

and electric

leakage.

The method

wiring

and

operation

refer to circuit diagram

1 and

circuit diagram

Cireuit

diagram

Circuit

diagram 2

Black

wire

Thite

vire

Ground

wire

nracrrireJ

I**.* I.n*

|ilrc

Supply

wire from

the

building

Summary of content (2 pages)

PAGE 1
READ AND SAVE THIS INSTRUCTION SHEET (t) arrrNrroN 1.1 To ensure the success of the installation, be sure to read t.2 1.3 1.4 1.5 1.6 these instructious and review the diagrams thoroughly before beginning. All electrical connections musl be iu accord.ance wilh local codes. ordinanses, or the National Electrical Code. If you are unfamiljar with the methods of installing electrical wiring, secure the servlces of a qualified licensed electrician.
PAGE 2
(s) msnunlrNc O{M,ET BOX IN THE BUIT,DING TIGURE rEE comrefl,@,@T0cEIHER P{TT THECONNECTED RODS TI{ROUGH TTIE HOLE OF CONNECTCIRS 2PCS (omoNAr) TME CONNECTOR iPC (mR GmmrD mE) FDITI]RE GROUND TTRE CROSSBAR IPC E TNSTRUCTT0N: muc scREr{s zPCS E suonr scREtts zPCS E urx NUTS zPCS GREEN SCREW lPC CANOPY NTJT CAPS zPCS STfl_1 @ r1{sN FEED TIIE rflRES THR0UGH CONNECTED RODS. oNTo@ (+) msraLLrNG trAy OUTLET BOX IN THE @ TrEouGH THE Horffi rN @, ADJUST TO THE DESmED mNGTH @.