Installation Guide

ManualsBrandsOrren Ellis ManualsCeiling LightsShrock 1 - Light Cone LED Pendant

Installation Guide

Tools You May Need

GOGGLES

TAPE MEASURE

RUBBER

GLOVES

PHILLIPS

LADDER

DRILL

SCREW DRIVER

Parts List

Circuit Box

Canopy Cover

Outlet Screws x 3

Wire Connectors x 3

Ground Screw x 1

Canopy Screws x 4

Please read and comprehend the entire manual before attempting to

assemble, operate, or install the product.

DO NOT CUT WIRES attached to the fixture under any circumstance.

Cutting wires will VOID your warranty. Excess cable should be neatly

looped and tucked into the canopy.

LED INFO & WARNINGS

•

All parts must be used as indicated in these instructions. Do not substitute

any parts, leave parts out, or use any parts that are worn or broken.

•

Inspect the LED fixture prior to installation to make sure that it has not

been damaged during shipping.

•

Please handle the LED light with care when unpacking. Do not apply

pressure to the LEDʼs, do not open any factory sealed compartments, and

do not touch the LEDs with your hands.

•

Place the wall switch in the “OFF” position of the room you are installing

the fixture.

•

Shut “OFF” the electricity at main fuse box.

•

Please remove the canopy from the box prior to the fixture body. Failure

to do so can potentially lead to cables getting tangled.

•

Make sure that you have all necessary parts by checking the parts list. If

any part is missing or damaged, please contact Customer Service for

a replacement.

We highly recommends to use a qualified, licensed electrician to install the

fixture.

We recommends to install the fixture on its own independent circuit. Do

not install the fixture on the same circuit with other appliances, or

HVAC systems.

•

Do not remove or replace manufactured driver that is provided

with the

fixture.

We recommends Single Pole Switch only. (This fixture does not

support dimmer switches).

Summary of content (6 pages)

PAGE 1
Installation Guide LED INFO & WARNINGS • Please read and comprehend the entire manual before attempting to assemble, operate, or install the product. • Make sure that you have all necessary parts by checking the parts list. If any part is missing or damaged, please contact Customer Service for a replacement. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn or broken.
PAGE 2
Fixture Diagram Outlet Box A Canopy Cover Ceiling D Ground Screw C Wire Connector B Outlet Screw E Canopy Screws
PAGE 3
Step 1. Adjust Height Locking Pin Cable The length of the cable is adjustable. To determine the proper length of the ﬁxture, hold the ﬁxture canopy up against the outlet box in the ceiling to adjust the cable. Depress locking pin on the canopy, hold pin in place, and pull down or push up on the cable. Repeat step for each cable.
PAGE 4
Step 2. Install Canopy Cover Outlet Box Ceiling A Canopy Cover Align canopy cover (A) and outlet screws (B) with outlet box. Outlet Box Ceiling A Canopy Cover B Outlet Screw Attach canopy cover (A) to outlet box with outlet screws (B).
PAGE 5
Step 3. Connect Wires A Canopy Cover Black (Line Wire) White (Neutral Wire) D Ground Screw Ceiling C Wire Connector Bare Copper (Ground Wire) Supply Wires: Connect Black (Line Wire) from ﬁxture to Black (Hot Wire) from outlet box. Connect White (Neutral Wire) from ﬁxture to White (Neutral Wire) from outlet box. Ground Wires: Connect Bare Copper (Ground Wire) from ﬁxture to Green or Bare Copper (Ground Wire) from outlet box. Twist wires together clockwise and secure with wire connector (C).
PAGE 6
Step 4. Mount Fixture Outlet Box A Canopy Cover E Canopy Screws Canopy Attach canopy to canopy cover (A). Secure with canopy screws (E). Step 5. Turn Power ON Turn electricity “ON” at main fuse box. Place the single pole switch in the “ON” position to test the ﬁxture.