Electrical Fireplace Stove with Heater OWNER’S MANUAL PLEASE SAVE THESE INSTRUCTIONS WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE. Thank you for choosing our Electric Fireplace. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. 2. 3. 4. Read ALL instructions before using this unit. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces.
SAVE THESE INSTRUCTIONS SPECIFICATIONS Voltage Rating 120 V (60Hz) Power Consumption 1500W Unit Size 37.5 in(W) x7.3 in. (D) x 22.6 in. (H) Unit Weight 22.9kg SAFETY FEATURES Overheat Safety Feature This heater is equipped with a overheat safety feature. When the heater’s internal components reach a certain temperature that could cause overheat or possible fire, the heater will automatically shut off.
Carbon bed Air outlet Control Panel Power Switch 4 Control panel
Flame: Change different flame colors Indicator: To indicate the light Low heat: To turn low heat on/off High heat: To turn high heat on/off Remote control Power switch: To turn on/off the fireplace Flame button: To turn on/off flame function, and Change different flame colors High heat button: To turn on/off high mode heating Low heat button: To turn on/off low mode heating PREPARATION 5
The heater can be wall-mounted or placed on the ground, which can be used in the living room or bedroom.Plug the unit into a 120 V 60 Hz electrical outlet, and open the switching power supply. Bring out the insulating film when used the remote control, see as the following steps. Wall-mounted installation instructions Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location be sure to follow thegeneral instructions included.
Screws position:Before installation, Loosen the Screws of the Wall Hanging Bracket on the back of the unit, then push it towards arrow direction.
Warning: to prevent fire, there is no other furniture on the top of the fireplace, the following are the minimum distance from the front and side of the heater to the wall. UP DOWN LEFT RIGHT 1.0m 0.5m 0.5m 0.5m Warning: check the wall to ensure that there are no wires, pipes, etc. when drilled holes in this area. Warning: the product is not plugged in before hanging wall. Warning: the heater cannot be fixed in the hollow wall. The heater must be installed on the solid wall.
Align the holes on both sides of the Hanging Wall Bracket to the holes on both sides of the wall. then push towards arrow Framing Specification: It is an embedded fireplace.No combustibles can be placed on the top surfaceof the fireplace. Combustibles may be installed to the edge of the unit. Insulation and vaporbarrier should be placed a minimum of 2 inches from the unit. Build the framing accordingto the specifications shown in the below table & figure 1. A B C D E F 9.65 37.7 23.2 37.4 22.
D G H E F ” OPERATING INSTRUCTIONS 1.Firstly, turn on the power switch on the right side of the fireplace, which can provide the power supply to all the function of the fireplace. Only in the state of mode I, the function will be operated, including the using of remote control. Press the power key on the remote control, at this time is to open the heating function and flame effect.
3.heating the low mode In standby mode, press the heat key of the first gear and can be opened the heating function. In standby mode, press the heat key on the control panel or remote control, the heating function is turned on (the heat indicator will light up).Then press the heat key on the control panel or remote control again, the heat function and the heat indicator are closed, at Or meanwhile, the fan will close after delaying 30 seconds. 4.
The method for removing the remote control battery is shown below; hold the battery card buckle, pull it out, and then remove the battery. RELEASE OPEN PUSH STORAGE Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit. TROUBLESHOOTING If the heater will not operate, please check the following before seeking repair advice: 1. Check if the power cord is plugged into an electrical outlet, if not, plug in. 2.
