Flat Wall Mounted / Free stand Electric Fireplace OWNER’S MANUAL Item #: (Stainless Steel Panel) Wall Hanging Mode Freestanding Mode AC 120V / 60Hz 1500W WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference.
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear.
WARNING For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties, and could cause injury. This product is not intended to be a primary heat source. It is for supplemental heat only. INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! NEVER modify this heater. Doing so could result in personal injury or property damage.
The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3-slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right). [NOTE: Adapter NOT INCLUDED.] SAVE THESE INSTRUCTIONS! Preparation This product includes a GLASS panel! Always use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
Installation and Assembly Rear View of Fireplace Minimum 39.4” (100 cm) 19.7” (50 cm) 19.7” (50 cm) Minimum 19.7” (50 cm) Step 1. Find a safe location. Minimum clearance on each side: 19.7” (50 cm). Minimum clearance below: 19.7” (50 cm). Minimum clearance above: 39.4” (100 cm). Minimum clearance from the front and sides: 19.7” (50 cm). Choose a location near an outlet so an extension cord is not required. DO NOT position the unit directly below a power outlet.
C 6
STEP2 ) Using the three wood screws (B) to fix the wall bracket , with wood screws thread the wall bracket and to lock with the drywall anchors, please tighten all wood screws. B E STEP 3) Have two people lift the fireplace machine up and insert the hooks ( 2 hooks on back of fireplace box) to the wall bracket slot.
STEP 4) With the fireplace installed safely, then using screws driver to lock the bracket and fireplace with two ST5x10 (D) screws in both sides.Check the appliance for stability ensuring that the appliance will not pull free from the wall.
IMPORTANT GLASS PANEL SAFETY INFORMATION! WARNING Under no circumstances should this product be operated with broken or chipped glass panels. Do not strike, slam or use blunt force on any part of the glass. Do not use abrasive cleansers to clean the glass. This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified professional. This next step involves GLASS! ALWAYS use extreme caution when handling glass.
Installation for Pebbles 10
NOTE: To install decorative pebbles, follow these steps. Have a capable adult help you. STEP 5A. While one person holds the glass panel, remove the two screws at the top edge of the fireplace with a Phillips (+) screwdriver. STEP 5B. Together, carefully remove the front glass panel and set it aside on a clean soft surface. STEP 5C. Set the plastic shelf (H) onto the ledge in the opening at the front of the fireplace. STEP 5D. Arrange the decorative pebbles (F) on the plastic shelf in the desired position.
Pages 2 and 3). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit. Methods of Operation This electric fireplace can be operated by the CONTROL PANEL, located on the right side panel of the fireplace (see figure below), or by the battery-powered REMOTE CONTROL. The operation and functions of the two methods are the same.
FLAME “+”: Makes flame effect brighter. NOTE: Flame effect stays on until power button is turned off. Flame effect must be FLAME + on for heater to turn on. HEATER button: Turns heater on and off. NOTE: The heater only works when the flame effect is on. If the flame effect is off, the heater will not turn on. NOTE: To prevent overheating, the heater HEATER blows cool air for 10 seconds before the heater turns on, and after it turns off. 1. Press once. Flame effect gets brighter. 2.
ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. Metal: Buff using a soft cloth, slightly dampened with a citrus oil-based product. DO NOT use brass polish or household cleaners as these products will damage the metal trim.
Troubleshooting ! WARNING DISCONNECT THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE. Problem Possible Cause Solution 1. Fireplace turns off 1. Fireplace has overheated 1. Reset switch by turning and safety device has main power switch off caused thermal switch to and waiting 10 minutes disconnect or home circuit then turning it back on. breaker has opened. 2. Reset circuit breaker. 1. Loose wiring.
7. Heater does not provide heat when turned on. 1. Thermal switch has been tripped. 2. Wiring is loose. 3. Heater is defective. 1. Turn unit off and unplug unit for 10 minutes. Plug back in and turn unit on. If plug cannot be reached, follow directions for tripped circuit breaker. 2. Disconnect from power source and inspect wiring for loose connections and repair or replace if necessary. 3. Replace heater.
