VUP-7240 & VUP-7240RX Wireless VoIP USB Phone & Wireless VoIP USB Phone Receiver User’s Manual Version 1.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. "ORtek Technology, Inc. declare that IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.
CONTENTS CHAPTER 1 Welcome to USB Phone 1.1 Features………………………………………..4 1.2 System Requirements……………………….5 1.3 Driver Installation…………………………….5 1.4 Hardware Installation……………………….6 CHAPTER 2 Use of USB Phone 2.1 Run Skype………………………………………..7 2.2 Connect USB Phone to PC…………………..8 2.3 Call to regular phone (PC to Phone)…….9 2.4 Answer a call…………………………………….9 2.5 Function Keys…………………………………..9 2.6 Function operation………………..………13 2.7 FAQ………………………………….…………...
CHAPTER 1 Welcome to Wireless USB Phone 1.1 Features 1. 2. 3. 4. 5. 6. Echo cancellation, noise reduction Full duplex communication Customized hand phone casing designs available Key-in tone function Hold ring tone function Clear and private conversation with Bluetooth technology 7. Works at full 360 efficient with Bluetooth Technology 8. Wireless freedom up to 15~20 meters 9. Talk up to 4 hours and standby up to 20 hours without recharging 10.
1.2 System Requirements 1. 2. 3. 4. 5. 1.3 PⅡwith 200 MHz CPU or better with USB interface 64MB of RAM 10MB or more hard disk space Operating System: Windows 2000/XP Network: LAN, ADSL, ISDN, 33.6K modem or better Driver Installation Insert the Driver CD into your CD-ROM drive and the CD will Auto Run. If it does not, please choose (Run) from the Start Menu. The file name on the CD is ”setup”. The first screen is an introduction. Read it before proceeding to the next step.
Note: If there is any update driver, users just need to install the new one. The driver will auto update. 1.4 Hardware Installation Connect the receiver to your PC, then the “Add New Hardware Wizard appears”. Just click the “Next” button, the system will install the driver automatically. No other steps are necessary. Click any button on the phone; it will connect with your computer.
CHAPTER 2 Use of USB Phone 2.1 Run Skype Download Skype software and install it (www.skype.com), the version. Run Skype and log in with skype account.
After the software startup, the icon will appear to the system tray as shown below: That indicates the Skype has successfully connected to Internet. If it hasn’t connected to Internet, the icon will be shown as , now you have to check whether PC is connected to Internet successfully or not. 2.
2.3 Call to regular phone (PC to Phone) Press "011"+"country code"+"phone number", then press . Example: call to Taiwan, Taipei, press 011886212345678, then press SEND key. 886 2 12345678 ----------------------------------------country code area code destination number Note: If you want to use this function, you should buy SkypeOut Credit first. 2.4 Answer a call When a incoming call and USB phone is ringing, press answer the call or press to to refuse the call. 2.
option; press this button to change the ring tone. ▼ S Change setting or switch option down. For example, if you choose the “RING TONE” option; press this button to change the ring tone. Call Skype window I. To see the contact person’s information. Including mobile, office and home phone Info number. II. During conversation, it will become the “Hold” function. I. Answer the phone II. Enter the function menu III. Press 3 seconds to turn on I. Hang up II. Exit the function menu III.
2.6 Function operation Press to enter the function menu, press to exit . There are four options that you can choose; you can press the “left” and “right” button to choose. Contacts: Under this option then press the button to see your contact list. Press the “up” and “down” button to look up your contact list. If your contact person is online, the “Online” will display on LCD. You can press the “Info” key to see the contact person’s detail information or press the button to call.
save your setting. For example, if you choose your favorite ring is 10. You need to press to save your setting. Setting the handset volume. Press the “up” button VOL SET: to increase the volume; press the “down” button to decrease the volume. The max volume is level 7. Setting the ring volume. Press the “up” button to RING VOL: increase the volume; press the “down” button to decrease the volume. ENTEEREG: For RF pairing use. KEY TONE: Setting the key tone ON or OFF.
2.7 FAQ Problem 1 The voice is played from the PC’s sound card instead of the USB phone when I make/answer a call? Solution Open the Main window of Skype, click on “File->Options”, and go to the table Hand/headsets, set Audio In, Audio Out and Ringing to the SkyWin USB Phone.
Problem 2 There is no voice comes out when play music? Solution Please execute the “Control Panel->Sound and Video ( )->Audio”, set Sound Playback and Sound Recording’s Preferred device to your sound card, it shown as below: 14
Problem 3 My USB phone cannot work on Windows 2000. Solution The Windows 2000 cannot support all of the Sounds and Audio Devices. So please download the DirectX from http://www.microsoft.com/ to solve this bug.
