Owner's Manual

1. Power/Standby LED
ThisLEDlightsredwhenanyzoneisactiveorthe
amplierisinstandbymode.
Front Panel
2. Zone LED
Blue:thecorrespondingzoneispoweredon.
OFF:thecorrespondingzoneiso(standbymode).
Red/Blue:Ashortcircuithappensonthespeakeroutputs
Rear Panel
1. Bus 12VDC Trigger In/Out
TheBus12VDCTriggerInisusedtoactivateallzonesthatare
usingtheBusInputanddisablesotherzonetriggersorsignal
sensingonthosezoneswhenitisused.WhetheBus12VDC
Triggerisused,allBus-controlledzoneLEDswillbeblueandac-
tive.IftheBusTriggerInhas12Vappliedtoit,onlythe12VBus
TriggerOutwillhave12VandtheZoneTriggerOutputswillnot.
2. Bus Inputs/Outputs
TheBusLineInputsareoptionalinputsthatcanbeusedtocon-
nectasinglesourcetomultiplezones.TheBusLineOutputsare
passivepassthroughthecorrespondingoftheBusInputsand
canbeusedtodaisychainthesourcetootherampliersinthe
system.
3. Line/Bus Switch
SwitchesthezoneinputtotheLineInput,BusInput1or
BusInput2.
4. Line Input
TheLineaudioinputforeachzoneisadedicatedsensinginput
thatwillactivatethezonewhenanaudiosignalfromasourceis
present.
5. 12VDC Trigger In/Out (Each Zone)
TheZone12VTriggerInisusedtoactivateaspeciczone.
TheZoneTriggerOutcanbeusedtotriggerother12Vdevices.
Thedelayandaudiosensingarebypassedwhenthe12VZone
TriggerInputisused.WhenaZoneTriggerisactive,thezoneLED
willbeblue.IfnovoltageispresentintheZoneTrigger,theZone
LEDwillbeo.StandbyModeTheamplierwillgointoStandby
modewhenaudiosignalortriggerisnotpresentafter3munites.
6. Speaker Outputs
Theminimumspeakerimpedanceis4ohmsforStereoModeand
8ohmsforBridgeMode.
7. Stereo/Bridge Switch
SelectstheoutputmodeofeachzoneforstereoorBridge
operation.
8. Gain Controls
LeftandRightgaincontrolsforeachzoneadjustthesoundlevel
independently.OnlyusingLeftcontroltoadjustthesoundlevel
whenusedinBridgeMode.
9. Voltage Switch
AC115VorAC230Vdualvoltageselector.
10. AC Input
Applythecorrectvoltagebeforeoperatetheamplier.
Specications
Power Output:
80W/Channel,1KHzinto4Ohms,OneZoneDriven
50W/Channel,1KHzinto8Ohms,OneZoneDriven
160W,1KHzinto8ohms,Bridge
Amplier Channels:
MX880:8Channels,4Zones
MX1280:12Channels,6Zones
MX1680:16Channels,8Zones
Signal-to-NoiseRatio:>90dBA-weighted
Frequency Response:20Hzto20KHz+1.7/-1dBat1Woutputinto8Ohms
Input Sensitivity:600mVfor80W@1KHz4OhmOneZone
700mVfor50W@1KHz8OhmOneZone
Input Impedance:>22KOhmsLineInput
Trigger Inputs / Outputs:BusandZone@12VDC
Zone Line Input:LineIn,BusIn1,BusIn2selectswitchperzone
Bridge Mode:SelectStereoorBridgemodeperzone8Ohmonly
Speaker Connectors:Detachablespeakerterminalssupportupto14awgwire
Delay Time:Whenaudiosignalortriggerisnotpresentafter5munites.
Power Requirements (Switchable):
MX880: 100-120VAC60Hz600WMax
 220-240VAC50Hz600WMax
MX1280: 100-120VAC60Hz900WMax
 220-240VAC50Hz900WMax
MX1680: 100-120VAC60Hz1200WMax
 220-240VAC50Hz1200WMax
Fuse Rating:
MX880: 100-120V/T5A,250V
220-240V/T2.5A,250V
MX1280: 100-120V/T8A,250V
220-240V/T4A,250V
MX1680: 100-120V/T10A,250V
220-240V/T5A,250V
Dimensions (L x W x H):16.81”x16.14”x3.46”
Weight:
MX880:19lbs.
MX1280:20.5lbs.
MX1680:22.8lbs.
MX SERIES MULTI ZONE AMPLIFIER OWNER’S MANUAL
MX SERIES MULTI ZONE AMPLIFIER OWNER’S MANUAL
MULTI-ZONE
DIGITAL AMPLIFIER
MX SERIES
MULTI-ZONE
DIGITAL AMPLIFIER
MX SERIES