Manual

AUDIO
OSD
OSD Audio introduces an unique line of outdoor omni in-ground speakers. When
properly installed, this product will provide you with many years of entertainment
pleasure.
Amplifier and Receiver Consideration
The omni speakers should be powered by an amplifier or receiver that provides
a minimum of 10 watts per channel
Optional Accessories -
Volume control - Heavy duty cables
Tools needed for installation
Wire
Spade or trench tool
Direct burial rated speaker cable
16AWG.............................................................................................................100 ft
14AWG..................................................................................................100 - 150 ft
12AWG..................................................................................................150 -2 00 ft
Specifications
Design:
Tweeter:
Woofer:
Frequency Response:
Power Handling:
Finishes:
Impedance:
Efficiency:
Dimensions:
Unit Weight:
Unit of Measure:
Weather resistant in ground loudspeaker
1” coaxial mylar wheezier cone
5-1/4” black polypropylene cone
50 Hz - 20 Khz
100W
Green
8 Ohms nominal
89 dB
8-1/2” x 9-1/8” x 8-1/2”
8 lbs x 2 (16lbs/pack)
Pair
Sold in pairs with a 2 year warranty
The Technical Support Center at OSD Audio is available between the hours of
8:30 AM - 5:30 PM PST, Monday through Friday, excluding holidays.
Warranty & Repair
All OSD Audio speaker products have (2) year Limited Warranty against defects in materials and
workmanship. Proof of purchase must accompany all claims. During the warranty period OSD
will replace any defective part and correct any defect in workmanship without charge for either
parts or labor.
OSD Audio may replace returned speakers with a product of equal value and performance. In such
cases, some modifications to the mounting may be necessary and are not OSD’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions.
If necessary, repairs must be performed by OSD. The unit must be returned to OSD at the owner's
expense and with prior written permission. Accidental damage and shipping damage are not
considered defects, nor is damaged resulting from abuse or from servicing performed by an
agency or person not specifically authorized in writing by OSD.
OSD Audio sells products only through authorized dealers and distributors to ensure that
customers obtain proper support and service. Any OSD product purchased from an unauthorized
dealer or other source, including retailers, mail over dealers and online sellers will not be honored
or serviced under existing OSD warranty policy. Any sale of product by an unauthorized source or
other manner not authorized by OSD shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To
return for repairs, you must email customer service at [e-mail] for a Returned Merchandise
Authorization (RMA) number# then the unit must be shipped to OSD at the owner's expense, along with
a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container
with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any
products that have been altered or modified • Any product whose identifying number of decal,
serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.
Step 1
Evaluate the location of the speakers. Project
the length of speaker wire you will run.
Note: when purchasing additional wire direct
burial grade is strongly recommended.
Omni Speakers reproduce sound in a full 360
degree and a few speakers will cover a large
area with sound if properly placed and
spread out.
Step 2
Dig A trench to run your speaker cable in.
Once you have decided on the locations for
your speakers, dig a hole about 5” to each
speaker location for the speaker wire.
For the Omni speaker, dig a trench hole
approximately 12” in diameter and 4” deep
should be dug for the speaker enclosure.
Step 3
Place the Omni speaker in the hole you have
dug. Run the direct burial wire through the
trench to the location of the amplifier or
receiver.
Please note: When connecting the additional
wire be sure to use water tight wire
connectors.
Step 4
Connect the wires from the omni speakers to
the amplifier or receiver. Please make sure
the polarity on the cables and speakers are in
sync.
Step 5
Turn on your amplifier or receiver to test the
speakers. If the speakers are operating
properly, refill wire trench and cover the
submerged part of the speaker.
OS 525
360 in ground speaker
Installation Instructions
0
OSD AUDIO • 775 Columbia St • Brea • CA • 92821 • www.osdaudio.com • Tel (888) 779 - 4968 • Fax (714) 256 - 8300