Owner's Manual

ManualsBrandsOSD Audio ManualsHome AudioOSD

OWNER’S MANUAL

XMP500DSP

OsdAudio ®

775 Columbia St.,

Brea. CA92821

www.osdaudio.com

XMP500 DSP man. 4/19

Congratulations on your purchase of the OsdAudio ® XMP500DSP.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or OsdAudio ® directly at 562 697 2600.

Please read your warranty and retain your receipt and original carton

for possible future use.

For more information about OsdAudio ® electronics, speakers and

accessories please visit www.osdaudio.com

XMP500DSP

Digital Stereo Power Amplifier

FEATURES:

MAIN / INTERRUPT priority input switching

MAIN auxiliary output

Speaker A/B switching

Front panel Balance and Volume controls

Signal sensing “Power On” and Trigger mode

SPECIFICATIONS

Stereo (8 ohm): 250W per channel, <1% THD+N

Stereo (4 ohm): 350W per channel, <1% THD+N

Bridged Mono (8 ohm): 700W, 1kHz, <1% THD+N

Frequency Response: 10Hz ~ 30kHz, -2dB/ +1dB

Signal to Noise Ratio: 100dB below 250W output into 8 ohms

w/20kHz Lowpass filter

Channel Separation: 65dB @ 1kHz, referred to 250W output

into 8 ohms

Input Sensitivity: 700mV input for rated 250W output

into 8 ohms

AC Power Consumption: 700W maximum

Net Weight: 9.85lbs / 4.6kgs

Gross Weight: 12.85lbs / 6kgs

2.15”

(55mm)

16.9” (435mm)

11”

(280mm)

Rear mounted treble and bass controls

Bass/Treble Control: +/- 12dB @ 100Hz and 10kHz

Summary of content (6 pages)

PAGE 1
XMP500DSP OWNER’S MANUAL XMP500DSP Digital Stereo Power Amplifier FEATURES: MAIN / INTERRUPT priority input switching MAIN auxiliary output Speaker A/B switching Front panel Balance and Volume controls Signal sensing “Power On” and Trigger mode Rear mounted treble and bass controls Congratulations on your purchase of the OsdAudio ® XMP500DSP. Please take a few moments to read this entire manual, and be sure to retain this document for future reference.
PAGE 2
XMP500DSP OWNER’S MANUAL CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL! EXPLANATION OF SAFETY SYMBOLS The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literatur e accompanying the appliance.
PAGE 3
XMP500DSP OWNER’S MANUAL 3 2 1 5 4 FRONT PANEL CONTROLS Figure 1. Front Panel 1. Power Switch Switches the XMP500DSP on or off. A red LED indicates connection to AC power while in standby mode. Turns green indicating audio signal is present. 2. Speaker Selector Selects speaker zone A or B. For A + B zones push both buttons in. 7 6 11 8 3. Service For uploading new firmware or update 4. IR receiver For uploading new firmware or update 12 14 15 SUB OUT 9 10 13 Figure 2. Rear Panel 5.
PAGE 4
XMP500DSP OWNER’S MANUAL 13. Voltage Selector Switch The amplifier can be used on 110 - 120V or 220 - 240V(50/60) line voltage. To change the operating line voltage, turn the power off using the power button and unplug the power cord. Remove the plastic cover screws and the plastic cover over and screws over the voltage selector switch. NOTE: If required,remove the IEC line core and replace with an IEC AC cable that matches the AC wall socket,this should be a 10A rated cable.
PAGE 5
XMP500DSP OWNER’S MANUAL Stereo or Bridged S t e r e o Balance Mode: Adjust Left & Right speaker balance. Balance Mode Choose from 10 preset EQ settings. 775 Columbia St.,Brea.
PAGE 6
XMP500DSP OWNER’S MANUAL APPLICATIONS Limited Warranty STEREO SETUP In this conﬁguration, the mode switch is set to “Stereo”. Connect the line out jacks from a stereo pre-ampliﬁer or source to the MAIN input jacks of your XMP500DSP. Next connect your speakers to the terminals marked “Speaker A” observing proper polarity. Select the “A” speakers using the front panel zone selection buttons. Connect a second (optional) pair of speakers to the terminals marked “Speaker B”.