Installation Manual
OTC
1-800-533-6127
1. Run the engine until it reaches
normal operating temperature before
performing the compression test.
2. Stop the engine. Disconnect all the
spark plug wires and number them
according to the cylinder they were
connected to.
3. Loosen all spark plugs about one
turn, but do not remove them. Use an
air hose or stiff brush to remove all the
dirt from the spark plug wells. Remove
the spark plugs and place them on a
clean, at surface in the order according
to the cylinder they were removed from.
4. Remove the air lter and set the
throttle plates to the wide open throttle
position, being careful not to damage
the linkage or throttle components.
CAUTION!
Failure to return throttle plates to closed
position before starting engine can
cause serious engine damage.
5. Disable the ignition system. Follow
the manufacturer’s recommendations, or
refer to a service manual for the proper
procedure.
6. Select the spark plug adapter and/or
hose required for the vehicle. Screw the
adapter and/or hose into a spark plug
well. Hand tighten only - DO NOT USE
A WRENCH. See Figure 1.
NOTE: On engines with long reach
plugs, use the long reach hose. Do not
use the long reach hose in short reach
holes – it may hit the top of the piston
and damage the engine.
7. Connect the coupling on the gauge
hose to the tting on the spark plug
hose. Be sure the hose couplings are
fully engaged.
8. Crank the engine for at least ve
compression strokes or until the
pressure reading stops rising on the
gauge.
9. Record the compression reading,
then push the side release valve to
relieve the pressure as shown in Figure
2. Repeat the test. Record the reading,
relieve the pressure, and remove the
hose from the spark plug well.
10. Reconnect the hose to the next
spark plug well to be tested and repeat
steps 6 through 10 for the remainder of
the cylinders to be tested.
Test Results
1. On a normal cylinder, the gauge
needle should travel up-scale on each
compression stroke until it reaches a
peak value. All cylinders should indicate
a pressure that is within the vehicle
manufacturer’s specications, and the
reading should not vary more than 10%
from cylinder to cylinder.
2. If the needle fails to travel up-scale
as described in paragraph 1 above, or if
it remains at the same value for several
strokes and then starts to climb, the
cylinder may have a sticking valve.
3. If the compression reading is
considerably higher than the vehicle
manufacturer’s specication, it may
indicate carbon build-up in the cylinder.
It may also indicate that the piston or
cylinder head has been modied.
4. If a reading on two adjacent cylinders
is 20 psi (or more) lower than the other
cylinders, a defective head gasket or
cracked cylinder head may be indicated.
Water (coolant) and oil may be found
in the two cylinders under these
conditions.
5. If the readings are low or vary widely
between cylinders, pour a teaspoon
of grade 30 oil into each cylinder
and retest. If the readings increase
considerably, the fault may be due to
poorly seated or worn piston rings. If
the readings remain about the same, the
valves and/or associated components
may be the cause. A burned or damaged
piston may also cause these results.
5606 Compression Tester Kit
Test Procedure
Repair Parts List
Part Number Description
0031-0460 Compression Gauge
0400-3009 Gauge Boot
0032-0137 26” Hose and
Release Valve
0180-0893 10mm Adapter
0180-1495 12mm Adapter
0180-1496 18mm Adapter
0032-0135 14mm Standard
Hose Assembly
0032-0136 14mm Long Reach
Hose Assembly
1000-5143 Repair Kit
0400-3109 Carry Case
0001-3894 Instruction Label
0001-000-3894 Rev B
6. Clean, regap, and reinstall the spark
plugs in the same order in which they
were removed, or install new spark
plugs. Reconnect each spark plug
wire to the spark plug it was connected
to. Return the throttle plates to closed
throttle position. Reconnect the ignition
system wiring, which was disconnected
in Step 5 of this Test Procedure.
Made in China
Figure 1
Installation of
Compression Gauge
Figure 2
Push Release Valve
to Relieve Pressure