User Manual

ManualsBrandsOtter Outdoors ManualsSports and recreationXT 650 Lodge

Page 1

Otter XT 650 Lodge

Installation and Set-Up Instructions

Otter XT 650 Lodge

Fits Magnum Otter Wild Sled Only

Parts Identification and Check List

P ARTS LIST

Item # Qty Part # Description

1 1 200814 Sled - Black

2 1 200889 Tent-XT 650 Lodge

3 1 80172 Frame Bracket “A”

4 1 80171 Frame Bracket “B”

5 1 80517 Back Wind Support Bar - 49 1/2”

6 1 80518 Center Wind Support Bar - 34 5/8”

7 1 80519 Center Wind Support Bar - 44 3/4”

8 1 80512 Adjustable Front Wind Support Bar

9 2 80470 Main Frame Extension Bar - 31 1/2”

1 0 2 80471 Main Frame Extension Bar - 32 1/2”

11 4 80472 Main Frame Extension Bar - 30”

1 2 2 80474 Outer Main Frame Bar - 33”

1 3 6 80473 Outer Main Frame Bar - 29 9/16”

1 4 4 80475 Middle Main Frame Bar - 52”

1 5 8 200384 Sleeve

16 16 400641 #8 x 3/4” Self Tapping Screw

1 7 8 200197 Black Plug

1 8 8 200195 Black End Cap

1 9 4 200615 5/16 Washer

2 0 12 400648 1/4 Nylon Hex Lock Nut

2 1 12 200942 3/8” Self Tapping Screw

2 2 16 200941 Plastic Protector

23 16 200943 Star Washer

MODEL NUMBERS:

Complete Pkg Otter XT 650 Lodge 200892

19 20

Front

Back

Center

Bottom

Back &

Center

Front

Bottom

All

22 23

Summary of content (10 pages)

PAGE 1
Otter XT 650 Lodge Installation and Set-Up Instructions Otter XT 650 Lodge Fits Magnum Otter Wild Sled Only Parts Identification and Check List MODEL NUMBERS: Complete Pkg Otter XT 650 Lodge 200892 2 1 PARTS LIST Item # Qty 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 10 2 11 4 12 2 13 6 14 4 15 8 16 16 17 8 18 8 19 4 20 12 21 12 22 16 23 16 Part # 200814 200889 80172 80171 80517 80518 80519 80512 80470 80471 80472 80474 80473 80475 200384 400641 200197 200195 200615 400648 200942 200941 200943 Description Sled
PAGE 2
Tools Required: 7/16” Box End Wrench 7/16” Socket and Ratchet Drill/Driver Phillips Bit 3/32 Drill Bit (optional) Note: Install bench seat before the fish house framework. 3/8 Bit 5/16 Bit 1. Position sled (Item 1) as shown in Diagram 1, with curved front to your left. Using front drilling pattern (on back page) mark two holes for the front frame bracket with a sharp object. Using rear drilling pattern (on back page), repeat this step for the rear frame bracket. 2.
PAGE 3
5. Assemble Back and Center Main Frame Bars: Insert the outer main frame bar (Item 13) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 16), plastic protector (Item 22) and star washer (Item 23). Slide the sleeve (Item 15) over the main frame extension bar (Item 11). (Line up holes with button lock, press lock in as you slide over the bar). Insert the black plug (Item 17) into the main frame extension bar (Item 11). Insert outer main frame bar (Item 13) into sleeve (Item 15).
PAGE 4
7. Assemble Front Main Frame Bar: Insert the outer main frame bar (Item 12) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 16), plastic protector (Item 22) and star washer (Item 23). Slide the sleeve (Item 15) over the main frame extension bar (Item 10). (Line up holes with button lock, press lock in as you slide over the bar). Insert the black plug (Item 17) into the main frame extension bar (Item 10). Insert outer main frame bar (Item 12) into sleeve (Item 15).
PAGE 5
9. Assemble Bottom Main Frame Bar: Insert the outer main frame bar (Item 13) into the middle main frame bar (Item 14). Fasten with self-tapping screw (Item 16), plastic protector (Item 22) and star washer (Item 23). Slide the sleeve (Item 15) over the main frame extension bar (Item 9). (Line up holes with button lock, press lock in as you slide over the bar). Insert the black plug (Item 17) into the main frame extension bar (Item 9). Insert outer main frame bar (Item 13) into sleeve (Item 15).
PAGE 6
11. Set up main frame bars by grasping with both hands and pushing upward until button clicks into place. Start with bottom main frame bar and continue to the back main frame bar pushing lengthened bars into appropriate position Ref. Diagram 9. Center Main Frame Bar Diagram 9 Back Main Frame Bar Front Main Frame Bar Note: Seat assembly not shown for clarity Button Location Both Sides Note: There are two holes that the buttons can click into to optimize the fit of the canvas. Bottom Main Frame Bar 12.
PAGE 7
13. Slide the tent over the main frame bar assembly, then fasten the velcro straps on the inside of the tent to each main frame bar. Ref. Diagram 11. Diagram 11 Tent Note: Collapsing the center and front main frame poles part way down will make installation easier. Main Frame Assembly 14. The canvas tent (Item 2) has a plastic trim seal sewn into the edge, snap the plastic trim seal to the edge of the sled (Item 1).
PAGE 8
15. On the front of the fishhouse, start in the corners and work inward, snap the plastic trim seal on the canvas tent (Item 2) to the top edge of the sled (Item 1) Ref. Diagram 13. Diagram 13 Start Here and work inward Right Side 1 Back Front Left Side 2 Start here and work inward Velcro attaches at this point 16. The tent (Item 2) will meet in the middle and should be free to open and close so it can be removed. To Collapse Tent and Transport: Fold tent inward towards sled. 1.
PAGE 9
OUTSIDE EDGE OF SLED HOLE DRILLING PATTERN FOR XT 650 LODGE PORTABLE FISH HOUSE USING MAGNUM OTTER WILD SLED NOTE: Back of sled is slightly wider than front of sled so hole placement is not the same. Otter XT 650 Lodge October, 2013 Otter Outdoors Inc. 411 W Congress St. • Maple Lake, MN 55358 Phone 320-963-6480 • www.otteroutdoors.
PAGE 10
Fish House Fabric Use and Care Guide Care must be taken during use to avoid damaging the fabric. Follow these guidelines to help protect the fabric. The warranty will not cover damage to the fabric because of wear, improper packing or abuse. 1. Do not pack any gear on top of the fabric. Propane tanks and augers can be especially damaging because of the sharp edges and the extra weight associated with them. 2.