User Manual

ManualsBrandsOttLite ManualsDesk LampsOttLite - Emerge LED Desk Lamp with USB Port

CONGRATULATIONS!

You’ve purchased the ﬁnest in natural lighting technology with your new OttLite

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail.

WARNING: To prevent electric shock, make sure the lamp is not plugged in until

all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) ﬂat on a steady surface.

Connect power adapter input (G) into connector (H) in the rear-bottom of the lamp.

3. Plug the power adapter (F) into a standard household 120V AC outlet. Note:

Only use with the supplied power adapter to avoid damage or ﬁre.

4. Power switch (B) is a “touch” switch that controls ON/OFF power, the LED

brightness settings, and the color mode function of the lamp.

To power LED settings, slightly touch the switch to achieve the following:

• Turn lamp “ON” to 1st brightness setting; touch the switch “once”;

• for 2nd brightness setting; touch the switch “two-times”;

• for 3rd brightness setting; touch the switch “three-times”;

• to turn lamp “OFF”; touch the switch “four-times”.

6. This lamp provides three color modes. To adjust lighting color mode, “touch”

switch (B) to turn “ON” lamp, then “touch” and hold switch (B) down for 1-2

seconds to change light color temperature mode; 5000°K, 2700°K, 4000°K.

7. To reposition the light, hold base (A) steady and grasp either lamp body (C) or

shade (D) depending on needed adjustment.

8. Refer to Diagrams 1 and 2 for lamp maximum adjustment range. NOTE: DO

NOT FORCE the shade outside allowable adjustable range as excessive

adjustment may cause damage.

CAUTION!

Device may become warm During charging. This is normal

anD parT of The charging process. charging Time varies by Device moDel.

SAFETY WARNING: To reDuce The risK of fire, elecTric shocK,

or inJury To persons

1. Turn lamp off and WAIT UNTIL LAMP HEAD (D) AND ADAPTER (F) ARE COOL

before handling.

2. The LED panel (E) might get hot after several hours of continuous use. DO NOT

place your hands directly on LED light panel.

3. Never use with an extension cord unless the plug can be fully inserted into the

receptacles in the extension cord.

4. Do not alter the plug.

5. The lamp head included with this unit cannot be replaced by the consumer.

6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not

meant to cover all possible conditions and situations that may occur. It must be

understood that common sense, caution, and care must be used with any electrical

product.

CAUTION!

if The exTernal flexible cable or corD of This luminaire is

DamageD, iT shall be exclusively replaceD by The manufacTurer or iTs service

agenT or a similar qualifieD person in orDer To avoiD a hazarD. inDoor use only.

CAUTION!

The lighT source of This luminaire is noT replaceable; when

The lighT source reaches iTs enD of life The whole luminaire shall be replaceD.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that of the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CAUTION: Any change or modiﬁcation to product not expressly recognized by

OttLite Technologies voids OttLite’s responsibility for proper function of product.

CAN ICES-005 (B)/NMB-005 (B)

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 0.8A

Output: 12V DC, 1.5A with a Male DC Plug

THIS LAMP CONTAINS a 5V, 2,1A USB output port (J) located on the bottom rear of

lamp. USB port can charge items such as tablets, cellular phones, etc.

English Emerge LED Desk Lamp

Emerge LED Desk Lamp

CS59009-SHPR H6FS

Diagram 1 Diagram 2

INS180454 REV122018