Specifications

ManualsBrandsOttLite ManualsElectrical EquipmentLED table lamp

CONGRATULATIONS!

You’ve purchased the ﬁnest in natural lighting technology with your new OttLite

product.

WARNING: To prevent electric shock, make sure the lamp is not plugged in until

all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

1. Remove lamp from packing, placing lamp body base (A) ﬂat on a steady

surface.

2. Connect power adapter input (B) into connector (C) in the rear-bottom of the

lamp.

3. Plug the power adapter (D) into a standard household 120V AC outlet. Note:

Only use with the supplied power adapter to avoid damage or ﬁre.

4. Turn the lamp ON & OFF using power switch (E) located in the front-upper

side of base (A). Power switch (E) is a “touch” switch that controls the dimmer

function for 3 levels of brightness and the color mode function of the lamp.

5. To power LED settings, slightly touch the switch to achieve the following:

• to turn lamp “ON” to ﬁrst lower-brightness; touch the switch “once”;

• for medium-brightness; touch the switch “twice”;

• for high-brightness; touch the switch “three-times”;

• to turn lamp “OFF”; touch the switch “four-times”.

6. This lamp provides three color modes. To adjust lighting color mode slightly

“press and hold” switch (E) for three seconds to switch light color temperature

mode; 5000°K, 2700°K, 4000°K. NOTE: 5000°K is the default color mode.

7. Wireless charger for Qi-certiﬁed devices (G) is located in the center of base (A).

See Wireless Charging Instructions section for details.

8. To position the shade simply move the shade (F) as needed to point the light.

Adjust joint screws (K) to to position lamp to desired position.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certiﬁed device. To determine if your device is

Qi-certiﬁed, please visit the Wireless Power Consortium website.

To wirelessly charge a device, perform the following:

• Place the device, which supports Qi wireless charging standard, face up on the

middle of the Qi wireless charging emblem (G).

• When the device is centered on the Qi wireless charging icon (G), a solid RED

light (H) will indicate the device is charging properly. NOTE: If RED light is

blinking this indicates the device is not charging and needs to be properly

centered.

• Check the charge level on your device periodically to determine when device is

fully charged.

CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL

AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.

SAFETY WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS

1. The light shade (F) might get hot after several hours of continuous use. Use

caution when moving the shade.

2. Never use with an extension cord unless the plug can be fully inserted into the

receptacles in the extension cord.

3. Do not alter the plug.

4. The lamp head included with this unit cannot be replaced by the consumer.

5. INDOOR USE ONLY.

NOTE: This product is intended for indoor use and the instructions may not cover

all possible indoor conditions or situations. Common sense, caution and care must

be used with any electrical product.

CAUTION!

IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS

DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE

AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.

INDOOR USE ONLY.

ONLY USE WITH THE SUPPLIED POWER ADAPTER TO AVOID DAMAGE OR FIRE.

THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE

REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

Any change or modiﬁcation to product not expressly recognized by OttLite

Technologies voids OttLite’s responsibility for proper function of product.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least

20cm from nearby persons.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

CAN RSS-216/CNR-216

CAN ICES-005 (B)/NMB-005 (B)

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 1.0A Max

Output: 12V DC, 2.5A with a Male DC Plug

Qi CHARGER SPECIFICATION:

Output: up to 5 Watts depending on device

THIS LAMP CONTAINS a 5V, 2,1A USB output port (J) located on the bottom rear of

lamp. USB port can charge items such as tablets, cellular phones, etc.

The “Qi” symbol is a trademark of the Wireless Power Consortium

Wireless Charging LED Table Lamp

CS4QTK1Z 1577128 W13

INS210662 REV070721