Instructions / Assembly
1.
Set Posts and Install Panels
■
** into Post tops and bottoms.
■
of Post and in Panel area
(Fig. 1)
.
■
(Fig. 2)
. Use an impact driver to loosely drive Panel Screws* into
(Fig. 2)
. Do not tighten screws yet.
2.
Install Posts on Fence
■
that Posts and Panel are level
(Fig. 3)
.
IMPORTANT! If fence top is not level across entire fence, position
extension sections higher than fence top to compensate
(Fig. 4)
.
■
Pre-drill front of fence with ¹⁵⁄₆₄
**
(Fig. 3)
.
■
Adjust Panel vertically until level and hand-tighten
screws securely. Do not overtighten.
3.
Install Additional Sections
■
Step 1, using one Post onlyStep 2,
attaching Panel to previously installed Post.
4.
Finish Fencing
■
** into unused Post holes
(Fig. 5)
.
PLEASE READ INSTRUCTIONS COMPLETELY BEFORE YOU BEGIN: Follow these instructions
to install panels within warranty and to avoid product damage.
We recommend following best building
practices for installing OUTDECO USA panels and posts in accordance with their intended purpose.
authorities about building codes/standards that may apply to your project.
OUTDECO Steel Panels & Posts have a 5-Year Limited Warranty for material integrity when installed per
Illustrations not to scale.
Black steel rendered in gray.
Suitable for pro
builders and DIY
crafters. Installation
requires 2 people.
16" Fence
Extension Post
See all Metal Panels at:
Decorative Steel Panels
& Wall Extension Posts
INSTALLATION INSTRUCTIONS
Installing Panels on 16" Fence Extension Posts
WHAT'S IN THE BOX
PANELS
1
48" x 16" or 72" x 16" Decorative Steel Panel
4
Panel Screws –
POSTS
1
16" Post
2
Wood Post Bolts, Washers, and Nuts
se ¹⁵⁄₆₄" drill bit
2
Post Caps –
2
Post Hole Plugs –
*
Included with Panel
**
Included with Post
§
Not Included
Product Details
■
OUTDECO Steel Panels are engineered to install directly on OUTDECO
18" Wall Extension Posts (see front) and 16" Fence Extension Posts.
■
Slots in panel sides align with pre-drilled holes on posts and allow
■
Panels can be mounted on timber posts or hung on walls/fences.
Fig. 5
NOTE: If back of fence is not accessible, use #8 or #10
wood screws
§
in appropriate length for 1" of post depth
+
your fence wood depth.
Panels and Posts
sold separately.
IMPORTANT! Install only on solid fences in good condition, with no loose boards. Post system intended for front of fence.
Recommend positioning posts to avoid screwing into fence rails.
WHAT YOU'LL NEED
Negative Carbon
Footprint Mill
Negative Carbon
Emissions
Temperature, UV &
Weather Resistant
Chemical
Adhesives
Panel Border
Drill Guide
Panel Border
Drill Guide
Drill Guide
10-Year Material
Warranty
100% CMYK BLACK
(recommend
magnetic type)
Drill
w/ ¹⁵⁄ ₆₄" Bit
w
/
Phillips Bit
Negative Carbon
Footprint Mill
Negative Carbon
Emissions
Temperature, UV &
Weather Resistant
Chemical
Adhesives
Panel Border
Drill Guide
Panel Border
Drill Guide
Drill Guide
10-Year Material
Warranty
100% CMYK BLACK
(6)
Negative Carbon
Footprint Mill
Negative Carbon
Emissions
Temperature, UV &
Weather Resistant
Chemical
Adhesives
Panel Border
Drill Guide
Panel Border
Drill Guide
Drill Guide
10-Year Material
Warranty
100% CMYK BLACK
Gloves
WARNING:
Wear gloves – panel edges can be sharp.
Fig. 4
Fig. 3
Fig. 2
PANEL
BACK VIEW
Fig. 1
Front of Fence
Facing Down
Approx. Panel Width
48" or 72"
outdecousa .com