Installation Guide

ManualsBrandsOutdoor Essentials ManualsGarden Center24 in. x 48 in. Raised Garden Bed Kit

Table Of Contents

ELEVATED GARDEN PLANTER

INSTALLATION INSTRUCTIONS

68956 U.S. Hwy 131, White Pigeon, MI 49099 616.365.4201 8902_7/16

www.outdooressentialproducts.com

STEP 1 STEP 2

•

Kit contents

• 2 – 32 in. "A1"

leg components

• 2 – 32 in. "A2"

leg components

• 2 – 32 in. "B1"

leg components

• 2 – 32 in. "B2"

leg components

• 2 – 10-1/2 in. x 46-1/4 in.

side assemblies

• 2 – 10-1/2 in. x 20-3/4 in.

end assemblies

• 1 – 22-1/2 in. x 46-1/2 in.

bottom tray

• 4 – 1x4 bottom supports

• 40 – Screws

Tools needed

• Drill

• #2 Phillips drill bit

Assemble one “A1/B1” leg and one “A2/B2” leg by fastening

together through the predrilled holes (ﬁg. 1).

Note: Do not assemble all four legs. Two legs will need to

remain unassembled for later steps.

Attach one leg on each side assembly (ﬁg. 2).

Side Assembly

Side AssemblyA1

Ledger

•

Ledger

•

ﬁg. 1

ﬁg. 2

Summary of content (4 pages)

PAGE 1
ELEVATED GARDEN PLANTER INSTALLATION INSTRUCTIONS Kit contents • • 2 – 32 in. "A1" leg components • 2 – 10-1/2 in. x 46-1/4 in. side assemblies • 2 – 32 in. "A2" leg components • 2 – 10-1/2 in. x 20-3/4 in. end assemblies • 2 – 32 in. "B1" leg components • 1 – 22-1/2 in. x 46-1/2 in. bottom tray • 2 – 32 in.
PAGE 2
ELEVATED GARDEN PLANTER INSTALLATION INSTRUCTIONS STEP 3 STEP 4 Place the legs with the side assemblies attached approximately 21" apart. Slide the end assembly between the two legs and fasten through the predrilled holes (fig. 3). Side Assembly • • Leaving a ¾" overhang, attach “A1” and “A2” to the side assemblies through the predrilled holes (fig. 4). • • Ledger End Assembly Ledger Ledger Ledger • • Side Assembly A2 • End Assembly • • Side Assembly • A1 Side Assembly fig. 4 fig.
PAGE 3
SEMBRADOR DE JARDÍN ELEVADO INSTRUCCIONES DE INSTALACIÓN Contenido del kit • • 2 piezas de 32 pulg. de patas “A1” • 2 ensambles laterales de 10-1/2 pulg. x 46-1/4 pulg. • 2 piezas de 32 pulg. de patas “A2” • 2 ensambles inferiores de 10-1/2 pulg. x 20-3/4 pulg. • 2 piezas de 32 pulg. de patas “B1” • 1 bandeja interior de 22-1/2 pulg. x 46-1/2 pulg. • 2 piezas de 32 pulg.
PAGE 4
SEMBRADOR DE JARDÍN ELEVADO INSTRUCCIONES DE INSTALACIÓN PASO 3 PASO 4 Coloque las patas con los ensambles laterales unidos aproximadamente a 21” de distancia. Deslice el ensamble inferior entre las dos patas y fíjelo a través de los agujeros previamente perforados (fig. 3). Ensamble lateral • • Dejando un excedente de ¾", sujete la “A1” y la “A2” a los ensambles laterales a través de los agujeros previamente perforados (fig. 4).