Gallery Electric Fireplaces Homeowner’s Installation Instructions & Operating Manual Model: GBI-34, GBI-41 Only use this heater as described in this manual. Any other use is not recommended by the manufacturer, and may cause fire, electric shock, or other personal injury. WARNING! Read and understand this entire owner’s manual, including all safety information, BEFORE plugging in or using this product. Failure to do so could result in fire, electric shock, serious personal injury, or death.
CONTENTS Important Safety Instructions ……………………………………………………………………………… 3 Specifications …………………………………………………………………………………………… …… 5 Preparation …………………………………………………………………………………………… …… 6 Installation …………………………………………………………………………………………… …… 6 ……………………………………………………………………………………………………… 8 Manual Button ……………………………………………………………………………………… 9 Remote Control ……………………………………………………………………………………… 9 Operation ………………………………………………………………………………………………… 10 Limited Warranty …………………………………………………………………………………………… 10 T
IMPORTANT SAFETY INSTRUCTIONS! When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: WARNING ALWAYS keep electric cords, home furnishings, drapes, clothing, papers, or other combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the bottom, sides, and rear of this heater.
WARNING Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace. Do not depend on the ON/OFF switch, the sole means of disconnecting power. ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
SPECIFICATIONS Model No. : GBI-34, GBI-41 Power: 120V/60Hz AC, 1500W Dimensions H1 H3 H2 INSERT: W2 W1 W3 D1 units: inch (mm) Model GBI-34 GBI-41 Over Size W1 H1 26.3 33.5 (850) (668) 40.4 31.4 (1025) (798) D1 11.4 (289) 11.4 (289) Flame View W2 H2 31.5 18.9 (800) (481) 38.4 24.1 (975) (611) Others W3 H3 31.6 25.4 (803) (646) 38.5 30.6 (978) (776) FRONT: LF, ARF, FAF units: inch (mm) INSERT FRONT MODEL SIZE MODEL NO.
PREPARATION 1. TOOL REQUIRED Magnetic Phillips Screw Driver 2. UNPACK THE FIREPLACE HEATER WARNING! Do NOT use this Electric Fireplace if any part has been under water. Immediately call a qualified service technician to inspect and to replace any part of the electrical system if necessary. Keep plastic wrapping away from children. WARNING! Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and assembly steps are grouped.
3. MANTEL FRAMING SIZE W4 D2 H5 H4 units: inch (mm) MODELS LF-34 / ARF-34 / FAF-34 LF-41 / ARF-41 / FAF-41 W4 33 (838) 40 (1016) D2 11.8 (300) 11.8 (300) H4 25.8 (655) 30.9 (785) H5 0 (0) 0 (0) 4. INSTALLATION: a. With front LF/ARF/FAF Fixing bracket Socket Screw ST4x8 Socket Insert 1.2 Secure the insert to the mantel panel with 2 ST 4x16 screws, OR If your cutout is larger than the firebox, fixing brackets can be used to relocate screw holes above the firebox in Step 1.3 1.
Screw ST4x16 Srcrew ST4x8 1.3 In case that the opening height of mantel is a little larger, first attach the fixing brackets to the firebox with ST4x8 screws, then use ST4x16 screws to attach brackets to the mantle. Airflow plate 1.4 Attach the airflow plate to the firebox with ST4x8 screws. Pegs Pin Magnets Magnet 1.5 Install the trim onto the insert by locating the pegs on both sides and inserting them into the receiving clips on the front of the fireplace.
1. Operating by Manual Button NOTE! The manual buttons on the fireplace unit do not operate all functions of this electric fireplace. Their purpose is to control some basic function if the remote control is misplaced or damaged. Please use the remote handset to carry out all functions. FLAME main power switch HEATER heater button flame button Main power switch The POWER switch supplies power to all of the functions of the fireplace.
BUTTOM FUNCTION POWER Press once turns appliance on. Press again turns appliance off. FLAME The fire has four flame effects, by pressing the flame effect button the unit will cycle through each effect. HEATER Press once turns 750W heater on. (Pilot lights illuminated ●○) Press again turns 1500W heater on (Pilot lights illuminated ●●) Press third time turns heater off.
TROUBLESHOOTING Problem Possible Causes Fireplace not responding to remote commands Fireplace trips circuit breaker or blows fuse when turned on Heater is excessively noisy Odor coming from heater/blower Switch on fireplace not in the ON position Switch must be in the ON position for remote operation Remote control battery dead or not inserted properly Insert or check battery for correct orientation Remote is not in range of fireplace or not aimed correctly Move closer to fireplace and aim remote