Use and Care Manual

ManualsBrandsOutdoor Living Today ManualsStorage & OrganizationSpa Breeze Shelter 11 ft. x 9 ft. Pergola

Customers agree to hold Outdoor Living Today and any Authorized Dealers free of any

liability for improper installation, maintenance and repair of any Outdoor Living Today

products.

9’X11’ Spa Breeze

Assembly Manual

Outdoor Living Today

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com sales@outdoorlivingtoday.com

Page 1

Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your

local building permit office to determine the correct hardware in your area.

If you plan to paint or stain your Spa Breeze before assembly, be sure to scribe or mark

the top edge of Joist where Stub Joists and Ladder Blockings are pre-marked. Painting

or staining may cover up markings making it more difficult to align components later.

Revision 3

March 20, 2012

In the event of a missing or broken piece, simply call the Outdoor Living Today

Customer Support Line @ 1-888-658-1658 within 30 days of the delivery of your

purchase. It is our commitment to you to courier replacement parts, free of charge,

within 10 business days of this notification. Replacement parts will not be

provided free of charge after the 30 day grace period.

Summary of content (16 pages)

PAGE 1
9’X11’ Spa Breeze Assembly Manual Outdoor Living Today Revision 3 March 20, 2012 Note: Post Mounting Hardware is NOT included in this kit. Please confirm with your local building permit office to determine the correct hardware in your area. If you plan to paint or stain your Spa Breeze before assembly, be sure to scribe or mark the top edge of Joist where Stub Joists and Ladder Blockings are pre-marked. Painting or staining may cover up markings making it more difficult to align components later.
PAGE 2
9X11 SPA BREEZE PERGOLA 3 LADDER SECTIONS M F D E C D C B H G ST PO E D SI N ST T ”I O 90 O P ON T FR I A Thank you for purchasing one of our Breeze Pergola's. Please take the time to identify all the parts prior to assembly.
PAGE 3
9x11 BREEZE PERGOLA HARDWARE PACKAGE Hardware Kit (Provided) 2” SS Finishing Nail Note: screws and nails shown actual size. 4” Square Drive Bit 2 1/2” Wooden Dowel (8) 2” Stainless Lag Screw and Washer (16 each) Tools Required Hammer (Not Provided) Screw Gun/Drill Level Pliers Tape Measure Ladders Safety Equipment Required Safety Glasses Toll Free 1-888-658-1658 Wood Clamp 9/16” Wrench 1/8” & 1/4” Drill Bits (Not Provided) Work Gloves www.outdoorlivingtoday.
PAGE 4
127 1/4 ” Important - Western Red Cedar Lumber and Timbers will have surface splitting that occurs as lumber seasons and drys to the moisture content in your area. Splitting or “checking”, as it is referred to, can be 1/8” to 1/4” wide and can run several feet. This does not diminish the structural integrity of the material in any way. t on Fr 101” de Si Important- If Spa is larger than 89”, position Spa on foundation now or use 3 Post Bases to make it easier to position Spa after Spa Breeze is built.
PAGE 5
Important- You will require the assistance of 2 helpers to support the posts up to Step 7. 2. Lift up a completed Post/Girder Assembly slowly and carefully. Make sure Girder is facing outward. Girder facing out. 3. If Post Mount Hardware is installed, position bottom of Posts in Hardware. Lag Screws Post Hardware 4. Secure Post to Post Hardware with appropriate hardware such as lag screws or a sufficient number of screws.(Hardware Not Supplied) 5.
PAGE 6
. Carefully lower (C) Girder down into notch of (B) Girders. Be careful not to twist the Girder when dropping down into place. Lag Screw Girder to Post. Pilot hole first. er ) (C rd Gi CG irde r Note; Pilot hole Post with 1/4” drill bit. (C) Gird er 2 Lag Screws to Post 7. Lift, position and Lag Bolt the second (C) Girder to Posts. Pre-marked for Stub Joist placement D 8. On level ground, position 1 Joist (D) E and 6 Stub Joists (E).
PAGE 7
9. With Stub Joists positioned correctly on Joist, attach each Stub Joist with 2 - 2 1/2” screws. Stub Joists should be flush with top and bottom of Joist with all notches facing down. There are two Joist / Stub Joist Assembly’s, complete both now. 2 - 2 1/2” screws Completed Joist / Stub Joist connections. 10. Carefully lift up completed Joist / Stub Joist Assembly and place Joist between Girders flush against posts and notch sitting down into Girder. 1 - 4” screw Jo ist (D ) 4” long screws 11.
PAGE 8
12. On a flat surface, position Ladder Blocking (F) where marked on top edge of Joist (D) and screw with 2 - 2 1/2” screws per end. Ladder Blocking should be flush with top and bottom of Joist with all notches facing down. D F D 2 - 2 1/2” screws per Blocking end. Joist is pre-marked for blocking placement. Completed Ladder Section 13. Complete all three Ladder Sections on the ground prior to moving to Step 14. 14. Carefully lift up one of the Ladder Sections between Girders.
PAGE 9
Notched slides onto Girder 7” 15. Carefully slide Joist notches of Ladder Section onto Girder. Try to align notches so they fall into place all at once. With notches of Ladder Section all sitting correctly on Girder, slide Section approximately 7” from Post. Check alignment of opposite end of Ladder Section. 16. Set all remaining Ladder Sections in place on Girder spacing each approximately 5 1/2” apart. 17. With all Ladder Sections in place, check once more for equal spacing.
PAGE 10
(H) Right Side Corner Bracket 18. There are 4 Left (G) and 4 Right Sided Corner Brackets (H). Corner Bracket Post Mounts (I) must be attached to the bottom end of each Corner Bracket before attaching to Posts. Wooden Dowel (I) Corner Bracket Post Mounts Hole 19. To assist you with Bracket and Post Mount alignment, both the end of the Bracket and Post Mount have been drilled for a Wooden Dowel. Wooden Dowels are found in the Hardware Kit Bag.
PAGE 11
4” screws countersunk 1/2” below surface. Bracket Spacer flush with bottom of Girder. Left Sided Corner Bracket Important- Posts may need to be aligned so they are true and square to mount Corner Brackets correctly. Use a Level to determine correct Post position. 21. Lift completed Left Sided Corner Bracket up and align bottom of Bracket Spacer flush with bottom of Girder. At bottom of Corner Bracket, align Post Mount evenly and tight against Post.
PAGE 12
Post Skirting Caps (L) Post Skirtings with Cleat (J) dado cut dado cut Post Skirting with Cleat (J) Post Skirtings - (K) Post Mount 24. Position 2 Post Skirtings with Cleats (J) on opposite sides of Post with Dado cuts facing to the inside as shown above. Cleat should be aligned tight against Post and not against Post Mount Hardware. tongue cut dado cut Post Skirting (K) 25. Slide the tongue and dado cuts of both Post Skirtings (K) Pieces into the ajoining tongue and dado cuts of Part J.
PAGE 13
27. Slide in 2nd Post Skirting piece and position and nail Post Skirting Cap as per Step 26. Place remaining Post Skirting Caps on Skirting and nail as per Step 26. Complete remaining Post Skirtings. Alignment String 28. Lift and position 2 - 2x2 Cross Members (M) up against outside Posts on both sides. Align with outside of B-Girders. Pre-drill Members first and attach with 4 - 2 1/2” screws per piece. At each end, attach a String (approx.
PAGE 14
2nd Interior Stub Joist. 30. Using the 2x2 Cross Member Templates, align and attach interior 2x2’s starting at the 2nd interior Stub Joist. Use 4 Members spaced 5 1/4” apart. Attach as per Step 29. 31. Continue attaching 2x2’s using Template for spacing and positioning ends with alignment strings. Attach as per Step 29. Optional Bar / Bench Seat Assembly (not included in Standard Kits) 32. Locate Bar Top (P) and flip over on flat, level ground.
PAGE 15
Leg Support Brackets have 1/8” Pilot Holes drilled. Leg Support Bracket 33. Place Leg Support Bracket (R) in corner and attach to Bar and Leg framing with 2 - 2 1/2”screws through pre-drilled holes in brackets. Complete 2 brackets per leg. End Panel Center Leg Panel 34. Complete remaining Leg Panels (center and end) following alignment and attachment procedures in Step 33. Bar Support Bracket has 3/8” Pilot Holes. 35. Set completed Bar /Seat Bench between Posts so flush on inside of Post.
PAGE 16
Congratulations on building your 9x11 Spa Breeze Pergola Note; Our Pergolas are shipped as an unfinished product. If exposed to the elements, the western red cedar lumber will weather to a silvery-gray color. If you prefer to keep the cedar lumber looking closer to the original color, we suggest that you treat the wood with a good oil base wood stain. You may also wish to paint your new Pergola rather than stain it. In both cases we recommend that you consult with a paint and stain dealer in your area.