Use and Care Manual

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [e-mail]
Page 2
A
B
L
D
CC
Q
Y
N
M
T
H
G
BB
O
E
Exploded View and Parts List for 4’x2’ Garden Chalet
AA
Z
F
C
I
J
K
V
W
X
R
DD
EE
Not Shown:
Interior Door Stop
Interior Silver Barrel Bolt
Shingle Spacing Template
P
S
Trim Section
H 2 - Front Corner Door Trims - 1/2” x 2 1/2” x 65 1/2”
L 1 - Upper Rear Horizontal Trim - 1/4” x 1 1/4” x 43 3/4”
M 2 - Side Skirting - 1/2” x 3 1/2” x 21”
N 1 - Rear Skirting - 1/2” x 3 1/2” x 45”
O 4 - Filler Trim - 1/2” x 1 1/2” x 33”
P 2 - Side / Front Corner Trim - 1/2” x 1 1/2” x 62”
Q 2 - Side / Rear Corner Trim - 1/2” x 2 1/4” x 66 3/4”
R 2 - Rear Corner Trim - 1/2” x 1 1/2” x 67”
S 1 - Center Rear Trim - 1/2” x 1 1/2” x 67”
T 1 - Front Door Header Trim - 1/2” x 1” x 41”
Shelf Section
AA 1 - Vertical Shelf Support - 1 1/2” x 1 1/2” x 35”
BB 4 - Shelf Supports - 3/4” x 1 1/2” x 17 3/4”
CC 2 - Shelves - 17 1/2” x 18 7/8”
Miscellaneous (Not Shown on Illustration above)
1 Interior Door Stop - 3/4” x 1 1/2” x 8”
1 Barrel Bolt Plywood Spacer - 1/2” x 2 1/2 x 2 1/2”
1 Interior Silver Barrel Bolt
1 Shingle Spacing Template - 1/8” x 7 1/2” x 40”
U
Floor Section
A 1 - Floor Section - 20 1/2” x 45” x 2 1/2”
B 4 - Floor Legs - 1 1/2” x 3 1/2” x 4”
Wall Section
C 2 - Side Walls - 18 1/2” x 62 1/2”
D 2 - Rear Walls - 22” x 67”
E 1 - Door Header - 1 1/2” x 2 1/2” x 41” - Dado Cut
G 2 - Angle Cut Gable Siding Pieces (left / right) - 1/2” x 18 1/2”
I 4 - Black “T” Hinges
J 2 - Door Panels - 20 1/4 x 61 3/8”
K 1 - Door Flange - 1/2” x 2 1/2” x 61 3/8”
Roof Section
F 1 - Roof Plywood - 5/8” x 21” x 44”
U 1 Sheet of Roofing Paper
V, 27 - 16” long x 5 1/2” wide Shingles
W 5 - 16” long x 2 3/4” wide Shingles
X 8 - 8 1/2” long x 5 1/2” wide Last Row Shingles
Y 1 - 8 1/2” long x 2 3/4” wide Last Row Shingle
Z 1 - Roof Ridge Cap - 1/2” x 2 1/2” x 47”
Parts List
Note: We recommend you drill a 1/8” pilot hole for each screw, to avoid splitting wood. The hole depth should be
equal to 3/4 the length of screw.
Note: All Trim and Skirting pieces are graded best face rough.
This means the rough side will be exposed when completing these Sections.