OVE INTELLIGENT TOILET Model 735H INSTRUCTION MANUAL Thank you for choosing OVE INTELLIGENT TOILET. Please read and understand this entire manual before attempting to assemble, operate or install this product. p.
CONTENT SAFETY NOTICE ............................................................................................. p.3 WARNINGS ...................................................................................................... p.4 PART LIST ........................................................................................................ p.6 INSTALLATION INSTRUCTIONS ..................................................................... p.7 BATTERY INSTALLATION ...................................
SAFETY NOTICE ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS. 1. It is forbidden to disassemble toilet by yourself. 2. Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow. 3. Please insure that the product is set more than 0.6 meter away from the bathtub. 4. Please make sure electric power is AC 110V +/- 10%.
WARNINGS Do not leave the toilet exposed to the sun. May cause yellowing or color fading. To prevent against power surge damages, make sure the ground is working in the power socket. Direct sunlight affects the good functioning of the remote. Radio or transmitting devices may interfere with the toilet’s remote control functions If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.
WARNINGS BATTERY USAGE SAFETY GUIDELINES 1. Always purchase the correct size and grade of battery most suitable for the intended use. 2. Clean the battery contacts and also those of the device prior to battery installation. 3. Remove batteries from equipment which is not to be used for an extended period of time. 4. Remove batteries if consumed or if product is to be left unused for a long time. 5. Do not mix old and new batteries. 6.
PART LIST STOP SPRAY MOVEB IDET MOVE DRYING FLUSHING WATER PRESSURE WATER TEMPERATURE NOZZLE FORWARD AIR PUMP AIR TEMPERATURE NOZZLE BACKWARD WATER PRESSURE SEAT TEMPERATURE NOZZLE WASHING A L N M B C K J I D G E F H Item Qty # A Seat 1 99TOI0014-OU B Electronic hardware 1 99TOI0039-OU C Control keypad (English & French) Control keypad (English & Spanish) 1 99TOI0040-OU 99TOI0046-OU D Water filter 1 99TOI0015-OU E Inlet valve 1 NOT SUPPLIED F Supply line 1
1 INSTALLATION INSTRUCTIONS 2 NOT SUPPLIED Remove the seat from the ceramic base. Simply pull the seat up gently. Be careful. 3 Position correctly the two fixing bolts of the floor drain. Follow manufacturer’s recommendations. 5 Position the toilet on the floor drain, making sure the fixing bolts are aligned with the toilet’s holes. Install the floor drain cover connector according to the manufacturer’s recommendations. 4 Insert the ring gasket under the toilet.
7 INSTALLATION INSTRUCTIONS 8 Snap Ring With care, re-install the seat on the ceramic base. 9 Pull-out the snap ring from the connector. Connect the filter’s flex-tube to the toilet’s water outlet and re-insert the snap ring. 10 NOT SUPPLIED Pull out the snap ring from the connector. Connect the filter’s flex-tube to the filter’s water inlet and re-insert the snap ring. Install the water inlet valve on the wall pipe. 11 Connect the supply line to the water inlet of the toilet. p.
INSTALLATION INSTRUCTIONS 12 Connect the supply line to the water inlet valve. 13 24h Apply silicone around the base of the toilet. Wait for 24h for it to dry. BATTERY INSTALLATION 14 2x 1.5V AA Battery (NOT INLCUDED) Load the remote with two AA batteries. The battery compartment is located at the bottom back of the remote and is opened by firmly sliding the cover downward. p.
FIRST TIME USE 1 Open the water supply inlet valve. 2 Plug the toilet in the power socket. 3 The toilet’s blue light will start blinking. The blinking light indicates that the wash tank is filling with water, a sensor in the toilet will stop the filling process automatically after around 3 minutes when the tank is full of water. After the wash tank is filled with water, the indicator light will stop blinking. 4 The toilet will turn ON automatically.
CONTROLS DESCRIPTION POWER: Press 1 time, it will turn the toilet ON. Press 2 times, it will turn the toilet OFF. ENERGY SAVER: When ON, the energy saving mode will decrease the electrical usage of the smart toilet when in stand-by. The seat will not be continuously pre-heated. LIGHT: Press the light key, the shimmer on the intelligent toilet lights up; press it again, the light turns off. NOZZLE WASHING: Press the nozzle washing key: the intelligent toilet pulls the Spray nozzle out.
CONTROLS DESCRIPTION STOP: Pressing this button will stop any ongoing function. SPRAY/MOVE: Pressing this button will initiate the Static Spray Cleaning function. Press it again to change to the Back-&-Forth Spray Cleaning function. *The SPRAY refers the 1 water jet function of the nozzle. BIDET/MOVE: Pressing this button will initiate the Static Bidet Cleaning function. Press it again to change to the Back&-Forth Bidet Cleaning function. *The Bidet refers the 5 water jets function of the nozzle.
CONTROLS DESCRIPTION AIR TEMP: Pressing this button will cycle through the 4 possible temperatures settings for the air drying function. 4 settings: OFF (Room temperature) / LOW / MEDIUM / HIGH SEAT TEMPERATURE: Pressing on this button will cycle through the 4 possible temperatures settings for the seat heating. 4 settings: OFF (Room temperature) / LOW / MEDIUM / HIGH NOZZLE FORWARD: Pressing this button during the Static Spray or Bidet cleaning will move the nozzle forward.
FEATURES SPRAY CLEANING (1 WATER JET) This function will only work if the user is sitting on the toilet. Press the SPRAY/MOVE button for spray cleaning. Water will spray and clean the user. Press the button again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect. BIDET CLEANING (5 JETS OF WATER) This function will only work if the user is sitting on the toilet. Press the BIDET/MOVE button for bidet cleaning.
INTELLIGENT FEATURES ENERGY SAVER ENERGY SAVER will cut down the electricity usage of your intelligent toilet during times of none-usage. The cleaning water tank will start heating the water only once the user is sitting on the toilet, whereas in normal mode, the cleaning water is kept to your preferences for your instant enjoyment. SOFT CLOSE DESIGN The toilet seat and seat cover have a soundless soft close design that prevents them from falling rapidly and denting or scratching the toilet.
CHANGING THE FILTER 1 Close the inlet valve, turn clockwise. Do not take out the filter before closing the inlet valve. 2 Pull-out the snap ring, pull the flex-tube out of the filter by pushing the plastic ring at the junction. 3 Install a new filter with the flex-tube. 4 Open the inlet valve counterclockwise. Make sure the water does not leak out. p.
LONG TERM STORAGE In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods. When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet. 1. Close water inlet valve. 2. Unfasten and remove the water drain bolt. 3. After draining all the water, please tightly screw the water drain bolt back into place. 4.
TROUBLESHOOTING Category Issue Toilet does not turn ON Seat cover electrical plug is not connected. Electronic fault. Startup Bidet water tank is not yet full. Toilet blue light flashing. Remote Root Cause Main power cord is not plugged in. Power socket does not work. Power socket GFCI has been triggered and needs to be resetted. Water inlet valves are closed,. No water is getting into the bidet tank. Water filter is clogged. Water is not getting to the bidet tank.
MAINTENANCE & CONSUMER RESPONSIBILITIES ■■ The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets. ■■ For daily maintenance, use a wet cloth and a soft liquid cleaner. ■■ Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.
INSTALLATION PICTURE p.
Save this manual for future reference Conservez ce manuel pour usage ultérieur Conserve este manual para futura referencia HEAD OFFICE / SIÈGE SOCIAL / OFICINA PRINCIPAL 2800 Etienne Lenoir, Laval Quebec H7R 0A3 Canada Customer service / Service à la clientèle / Service al cliente Tel.: 1-866-839-2888 Fax: 1-866-922-9990 8:00 am - 5:00 pm E.S.