OVE SMART TOILET Model ALFRED (IT-415) INSTRUCTION MANUAL WATCH OUR YOUTUBE INSTALLATION VIDEO https://youtu.be/Fitsmm5qjcM 29-1/8 in 740 mm 23 in 585 mm 16-9/16 in 420 mm 12 in 305 mm Thank you for choosing OVE SMART TOILET. Please read and understand this entire manual before attempting to assemble, operate or install this product. p.
CONTENT SAFETY NOTICE ............................................................................................. p.3 WARNINGS ...................................................................................................... p.4 PART LIST ........................................................................................................ p.5 INSTALLATION INSTRUCTIONS ................................................................. p.6-8 FIRST TIME USE ...........................................
SAFETY NOTICE ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS. 1. It is forbidden to disassemble toilet by yourself. 2. Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow. 3. Please insure that the product is set more than 0.6 meter away from the bathtub. 4. Please make sure electric power is AC 120V.
WARNINGS Do not leave the toilet exposed to the sun. May cause yellowing or color fading. To prevent against power surge damages, make sure the ground is working in the power socket. Direct sunlight affects the good functioning of the remote. Radio or transmitting devices may interfere with the toilet’s remote control functions If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.
PART LIST o J A K I C H B D G E F Item Qty # A Light Indicator Panel 1 -- B Toilet Water Inlet 1 -- C Water Filter 1 99TOI0144-OR D Water Supply Hose 1 99TOI0143-OR E Water Tube 1 99TOI0146-OR F Side Control Panel 1 -- G Seal ring 1 99TOI0148-OR H Seat 1 99TOI0156-OR I Seat Opening Sensors 2 -- J Remote Receiver 1 -- K Remote 1 99TOI0152-OR p.
2 30 150mm 1 INSTALLATION INSTRUCTIONS 5m m m 0m 40 Ensure that your water inlet pipe and your floor discharge drain are installed according to the drawing. These are minimum measurements, the toilet can be installed if your actual measurements are longer than shown. TIP: Align 2 pieces of masking tape with the center of the drain, this will help you position the toilet in future steps. 3 NOT SUPPLIED Install the floor flange according to the manufacturer’s recommendations.
INSTALLATION INSTRUCTIONS 7 (optional) With care, remove the whole tank and the seat from the ceramic base. Gently set it aside on a soft surface. 9 8 Place the seal ring under the toilet. 10 Position the toilet onto the floor flange, making sure the fixing bolts are aligned with the toilet’s holes. Install the washers and nuts onto the two fixing bolts of the floor flange. 11 12 Using a ratchet, tightly screw the nuts to the fixing bolts.
13 INSTALLATION INSTRUCTIONS 14 24h Connect the water inlet hose to your existing shut off valve on the wall. Then connect the other end of the hose to the toilet’s water inlet located at the back, underneath the filter. Apply silicone around the base of the toilet. Wait for 24h for it to dry. p.
FIRST TIME USE 1 Open the water supply shut off valve. 2 Plug the toilet in the power socket. 3 The toilet will turn ON automatically. The toilet’s lights will start blinking from left to right circularly. The toilet will give out one short beeping sound when the lights blinking has complete 1 cycle. The blinking light indicates that the bidet water tank is filling with water, the toilet seat and the cleaning water are warming up.
CONTROLS DESCRIPTION SIDE CONTROL PANEL POWER: Pressing this key will stop any ongoing function. Pressing for 3 seconds will turn the power ON / OFF. SPRAY/MOVE: Pressing this key will initiate the Static Spray Cleaning function. Press it again to change to the Back-&-Forth Spray Cleaning function. *The SPRAY refers the 1 water jet function of the nozzle. DRYING: Pressing this key will initiate the Static Air Drying function. While not seated on the toilet, pressing this key for 5 sec.
CONTROLS DESCRIPTION POWER: Pressing this key will stop any ongoing function. Pressing for 3 seconds will turn the power ON/OFF. o ECO MODE: Pressing the key will turn ON/OFF the ECO MODE function. FLUSH: Pressing this key will flush the toilet. Press this key for 5 sec., the AUTOMATIC FLUSHING FUNCTION will be turned OFF. Press it again for 5 sec. to turn this function ON again. SPRAY/MOVE: Pressing this key will initiate the Static Spray Cleaning function.
FEATURES SPRAY CLEANING (1 WATER JET) This function will only work if the user is sitting on the toilet. Press the SPRAY/MOVE key for spray cleaning. Water will spray and clean the user. Press the key again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect. BIDET CLEANING (4 JETS OF WATER) This function will only work if the user is sitting on the toilet. Press the BIDET/MOVE key for bidet cleaning.
SMART FEATURES ECO MODE ECO MODE will cut down the electricity usage of your smart toilet during times of none-usage. The bidet water tank and the seat will start heating only once the user is sitting on the toilet, whereas in normal mode, the bidet water and seat are kept to your preferences for your instant enjoyment. AUTOMATIC OPEN/CLOSE SEAT The smart toilet is equipped with a sensor which will automatically open and close the seat when the user is nearby or leaving.
CLEANING THE FILTER 1 Close your shut off valve, turn clockwise. Do not take out the filter before closing the shut off valve. 3 Unscrew the filter cover by turning counterclockwise and take out the filter. 5 Re-Install the filter. Safely tighten the filter to avoid leakage. 2 Reach the filter behind the toilet ceramic base. If the filter is unreachable due to limited space between the toilet and the wall, uninstall the whole seat from the ceramic base. (see installation instructions steps 4 to 7).
LONG TERM STORAGE In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods. When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet. Press simultaneously the DRYING and BIDET keys together for 3 seconds. The toilet will take 2 minutes to drain its water content and power off automatically. It is now ready for storage.
SPECIFICATION SHEET Item Electric Load Electric Cord Content AC 120V / 500W / 60HZ 1.5 m insulated power cord Cleaning System Spray Cleaning (1 jet) Bidet Cleaning (4 jets) Water Temp Heater Capacity Cleaning Tank Capacity Overheating Safety Anti-Reflux Water pressure 0.1-0.6 MPa / 14.5-87.0 psi Water pressure 0.1-0.6 MPa / 14.5-87.0 psi From ambient temperature to 40 C AC 120V / 450W / 60HZ 0.9 L Temperature safety reset protector integrated. Toilet will shutdown if temp. is out of specs.
MAINTENANCE & CONSUMER RESPONSIBILITIES ■■ The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets. ■■ For daily maintenance, use a wet cloth and a soft liquid cleaner. ■■ Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.
INSTALLATION PICTURE p.
Save this manual for future reference Conservez ce manuel pour usage ultérieur Conserve este manual para futura referencia HEAD OFFICE / SIÈGE SOCIAL / OFICINA PRINCIPAL 2800 Etienne Lenoir, Laval Quebec H7R 0A3 Canada Customer service / Service à la clientèle / Service al cliente Tel.: 1-866-839-2888 Fax: 1-866-922-9990 customerservice@ovedecors.com 8:00 am - 5:00 pm E.S.