OVE SMART TOILET Model GODFREY (IT-416) INSTRUCTION MANUAL WATCH OUR YOUTUBE INSTALLATION VIDEO https://youtu.be/2AhhMBGu4rU 29-1/8 in 740 mm 23 in 585 mm 16-9/16 in 420 mm 12 in 305 mm Thank you for choosing OVE SMART TOILET. Please read and understand this entire manual before attempting to assemble, operate or install this product. p.
CONTENT SAFETY NOTICE ............................................................................................. p.3 WARNINGS ...................................................................................................... p.4 PART LIST ........................................................................................................ p.5 INSTALLATION INSTRUCTIONS ................................................................. p.6-7 TIPS FOR RE-INSTALLING SIDE PANELS .......................
SAFETY NOTICE ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS. 1. It is forbidden to disassemble toilet by yourself. 2. Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow. 3. Please insure that the product is set more than 0.6 meter away from the bathtub. 4. Please make sure electric power is AC 120V.
WARNINGS Do not leave the toilet exposed to the sun. May cause yellowing or color fading. To prevent against power surge damages, make sure the ground is working in the power socket. Direct sunlight affects the good functioning of the remote. Radio or transmitting devices may interfere with the toilet’s remote control functions If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.
PART LIST o I A B J H C G D E F Item Qty # A Light Indicator Panel & Flush button 1 -- B Toilet Water Inlet 1 -- C Water Filter 1 99TOI0144-OR D Water Supply Hose 1 99TOI0143-OR E Water Tube 1 99TOI0146-OR F Side Control Panel 1 -- G Seal ring 1 99TOI0148-OR H Seat 1 99TOI0162-OR I Remote Receiver 1 -- J Remote 1 99TOI0152-OR p.
2 30 150mm 1 INSTALLATION INSTRUCTIONS 5m m m 0m 40 Ensure that your water inlet pipe and your floor discharge drain are installed according to the drawing. These are minimum measurements, the toilet can be installed if your actual measurements are longer than shown. TIP: Align 2 pieces of masking tape with the center of the drain, this will help you position the toilet in future steps. 3 NOT SUPPLIED Install the floor flange according to the manufacturer’s recommendations.
INSTALLATION INSTRUCTIONS Remove the 2 plastic side panels from the toilet by firmly pulling them straight up. 9 8 Place the seal ring under the toilet. 10 Position the toilet onto the floor flange, making sure the fixing bolts are aligned with the toilet’s holes. Using a ratchet, tightly screw the nuts to the fixing bolts. 11 12 24h With care, re-install the side panels and the seat on the ceramic base. See next page for more details.
TIPS FOR RE-INSTALLING SIDE PANELS A Start by aligning the 3 pegs on the back of the side panel with the 3 corresponding brackets on the back of the toilet. B Make sure the 3 back pegs are aligned onto their corresponding brackets and insert the back panel flange behind the ceramic base. Push firmly on the side panel in order to yield an even gap between the side panel and the ceramic base. C Finally, keep pushing horizontally and at the same time firmly push downward.
FIRST TIME USE 1 Open the water supply inlet valve. 2 Plug the toilet in the power socket. 3 The toilet will turn ON automatically. The toilet’s lights will start blinking from left to right circularly. The toilet will give out one short beeping sound when the lights blinking has complete 1 cycle. The blinking light indicates that the bidet water tank is filling with water, the toilet seat and the cleaning water are warming up.
CONTROLS DESCRIPTION SIDE CONTROL PANEL POWER: Pressing this key will stop any ongoing function. Pressing for 3 seconds will turn the power ON / OFF. SPRAY/MOVE: Pressing this key will initiate the Static Spray Cleaning function. Press it again to change to the Back-&-Forth Spray Cleaning function. *The SPRAY refers the 1 water jet function of the nozzle. DRYING: Pressing this key will initiate the Static Air Drying function. While not seated on the toilet, pressing this key for 5 sec.
CONTROLS DESCRIPTION POWER: Pressing this key will stop any ongoing function. Pressing for 3 seconds will turn the power ON/OFF. o ECO MODE: Pressing the key will turn ON/OFF the ECO MODE function. FLUSH: Pressing this key will flush the toilet. Press this key for 5 sec., the AUTOMATIC FLUSHING FUNCTION will be turned OFF. Press it again for 5 sec. to turn this function ON again. SPRAY/MOVE: Pressing this key will initiate the Static Spray Cleaning function.
FEATURES SPRAY CLEANING (1 WATER JET) This function will only work if the user is sitting on the toilet. Press the SPRAY/MOVE key for spray cleaning. Water will spray and clean the user. Press the key again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect. BIDET CLEANING (4 JETS OF WATER) This function will only work if the user is sitting on the toilet. Press the BIDET/MOVE key for bidet cleaning.
SMART FEATURES ECO MODE ECO MODE will cut down the electricity usage of your smart toilet during times of none-usage. The bidet water tank and the seat will start heating only once the user is sitting on the toilet, whereas in normal mode, the bidet water and seat are kept to your preferences for your instant enjoyment. SOFT CLOSE DESIGN The toilet seat and seat cover have a soundless soft close design that prevents them from falling rapidly and denting or scratching the toilet.
CLEANING THE FILTER 1 Close your shut off valve, turn clockwise. Do not take out the filter before closing the shut off valve. 3 Unscrew the filter cover by turning counterclockwise and take out the filter. 5 Re-Install the filter. Safely tighten the filter to avoid leakage. 2 Uninstall the seat and the right side panel. (see installation instructions steps 4 to 7) Clean the filter. Use a tooth brush to clean the dirt on the filter. Use a cloth to clean the dirt and deposits in filter body.
LONG TERM STORAGE In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods. When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet. Press simultaneously the DRYING and BIDET keys together for 3 seconds. The toilet will take 2 minutes to drain its water content and power off automatically. It is now ready for storage.
SPECIFICATION SHEET Item Electric Load Electric Cord Content AC 120V / 500W / 60HZ 1.5 m insulated power cord Cleaning System Spray Cleaning (1 jet) Bidet Cleaning (4 jets) Water Temp Heater Capacity Cleaning Tank Capacity Overheating Safety Anti-Reflux Water pressure 0.1-0.6 MPa / 14.5-87.0 psi Water pressure 0.1-0.6 MPa / 14.5-87.0 psi From ambient temperature to 40 C AC 120V / 450W / 60HZ 0.9 L Temperature safety reset protector integrated. Toilet will shutdown if temp. is out of specs.
MAINTENANCE & CONSUMER RESPONSIBILITIES ■■ The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets. ■■ For daily maintenance, use a wet cloth and a soft liquid cleaner. ■■ Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.
INSTALLATION PICTURE p.
Save this manual for future reference Conservez ce manuel pour usage ultérieur Conserve este manual para futura referencia HEAD OFFICE / SIÈGE SOCIAL / OFICINA PRINCIPAL 2800 Etienne Lenoir, Laval Quebec H7R 0A3 Canada Customer service / Service à la clientèle / Service al cliente Tel.: 1-866-839-2888 Fax: 1-866-922-9990 customerservice@ovedecors.com 8:00 am - 5:00 pm E.S.