SHELBY SIDE PANEL 32 ITEM #667456 Measures: millimeter [inch] 3 81 ] 3 [ 2 91 4 [36 / 12 ] / 19 [48 / 1 ] / 524 [60 ] Opening 520 / 560 [20 1/2] / [22 1/32] 1877 [73 27/32] 1877 [73 27/32] 275 [10 13/16] 425 [16 3/4] CSA Markings An installation video guide can be found on our Youtube channel. http://youtu.
SAFETY INFORMATION CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: • Always wear safety glasses and gloves while handling. • Always read and follow all the steps in the installation instructions. • Inspect all contents and glass for damage before installation.
TABLE OF CONTENT PACKAGE CONTENT.......................................................................................................................................... 5 HARDWARE CONTENT...................................................................................................................................... 6 TOOLS REQUIRED............................................................................................................................................. 6 SHOWER REVERSIBILITY........
PACKAGE CONTENT M N O B E Y X 4
PACKAGE CONTENT PART# DESCRIPTION QTY CODE B Wall track 1 99STR1047-WM E Side panel 1 99SG10028-WM M Support bar’s anchor 1 99SGC1046-WM N Long support bar 1 99SGS1020-WM O Glass panel’s bracket 1 99SGC1045-WM X Glass panel clamp 1 99SGC1044-WM Y Fixed panel’s bottom seal strip (Long) 1 99SRU0003 5
HARDWARE CONTENT AA BB DD EE Screw ST4x15mm 3+1 Screw ST4x20mm 1+1 Screw ST4x30mm 1+1 Screw ST4x30mm 4+1 FF GG HH Wall Anchor ø6x30mm 5+1 Fitting x3 Cap x3 TOOLS REQUIRED Pencil Measuring Tape Safety glasses Drill with ceramic tile bits ø3mm (1/8in) & ø6mm (1/4in) Silicone Rubber mallet Allen key 2.
SHOWER REVERSIBILITY • This instruction is drawn up for an opening from right to left (see illustration A). • For an installation from left to right (see illustration B), use the same instructions, but switch around the panels: mirror effect.
BASE INSTALLATION GUIDELINES FOR TILE WALL (OPTIONAL) 1 2 Studs Tile wall Shower Base Drywall Cement Flange Silicone Floor Shower Base 3 4 Wood shim Flange Stud 5 Drywall Silicone 8
WALL TRACK INSTALLATION 1. Level the track (B) and mark the track holes’ positions. 2. Remove the track and drill pilot holes in the marked locations with a Φ6mm (1/4in) drill bit. 3. Insert the wall anchors (FF) using a rubber mallet until the wall anchors are flush with the wall. 4. Replace and secure the track (B) with screws (EE). Do not overtighten.
SIDE PANEL INSTALLATION 1-2. Insert the fixed panel’s bottom seal strips (Y) at the base of side panel (E). Cut the surplus part for the clamp. 3. Insert the side panel (E) into the metal track (B). Do not fully tighten it as further adjustments may be required.
SIDE PANEL INSTALLATION 1-2. Insert the 2 magnetic door seal strips on the door panel and the side panel (E). 3. Place the glass panel clamp (X) into the side panel (E), mark the hole’s place and make a hole in the base using ø3mm (1/8in) drill bit. 4. Secure the glass panel clamp (X) using screw (BB). 5. Completely install the glass panel clamp (X) using 4mm Allen key. 6. Drill the side panel (E) with Φ 3mm (1/8in) in 3 places. 7. Secure the side panel (E) with fittings (GG), screws (AA) and caps (HH).
SUPPORT BAR INSTALLATION 1-2. Install the glass panel’s bracket (O) and the support bar’s anchor (M) onto the support bar (N). 3. Mark the outline of the support bar’s anchor (M). 4. Completely remove the support bar (N). Place the support bar’s anchor (M) back on it’s wall mark, mark the hole of it. 5. Drill a hole on the center marks with a ø6mm (1/4in) drill bit. 6-7. Insert the wall anchors (FF) using a rubber mallet. Fix the center fitting on the support bar’s anchor (M) using the screw (DD). 8-9.
SEALING Ensure that the door closes and opens smoothly, and that there is a tight connection between the side glass panels and the frame as well as the support bar. Apply a clear silicone water sealant around the outside perimeter of any fixed shower components (horizontally between bottom of fixed glass panel, side panel and base, as well as vertically between the wall, glass frames, and any side glass panel). Allow 24 hours for silicone to dry.
OVE Decors ULC LIMITED Product Warranty OVE is a distributor of the following Products: • Shower Doors (warranty period 5 years). • Acrylic Surfaces (warranty period 5 years against blistering, cracking or chipping in the acrylic surface). • Acrylic Shell Structure (warranty period 5 years against loss of water through fiberglass laminate of the acrylic body).
SHELBY PANNEAU LATÉRAL 32 ITEM #667456 Mesures: millimètres [pouces] 3 81 ] 3 [ 2 91 4 [36 / 12 ] / 19 [48 / 1 ] / 524 [60 ] Ouverture 520 / 560 [20 1/2] / [22 1/32] 1877 [73 27/32] 1877 [73 27/32] 275 [10 13/16] 425 [16 3/4] Marques CSA Un guide d’installation video est disponible sur notre chaîne Youtube. http://youtu.
INFORMATION SUR LA SÉCURITÉ AVERTISSEMENT Veuillez lire attentivement les importantes consignes de sécurité suivantes avant la manutention et l’installation de cette douche. La manipulation de ce produit présente un risque de blessure grave. Pour minimiser ces risques, veuillez prendre note de ce qui suit: • Toujours porter des lunettes et des gants de sécurité pendant la manutention. • Toujours lire et suivre toutes les étapes indiquées dans les instructions d’installation.
TABLE DES MATIÈRES CONTENU DE L’EMBALLAGE ......................................................................................................................... 19 QUINCAILLERIE FOURNIE .............................................................................................................................. 20 OUTILS REQUIS ............................................................................................................................................... 20 CETTE DOUCHE EST RÉVERSIBLE ....
CONTENU DE L’EMBALLAGE M N O B E Y X 18
CONTENU DE L’EMBALLAGE # DE PIÈCE DESCRIPTION QUANTITÉ CODE B Rail d’aluminium 1 99STR1047-WM E Panneau latéral 1 99SG10028-WM M Ancrages pour barre de support 1 99SGC1046-WM N Barre de support longue 1 99SGS1020-WM O Raccords pour panneau fixe 1 99SGC1045-WM X Attache de soutien des panneaux de verre 1 99SGC1044-WM Y Joint d’étanchéité du bas du panneau fixe (long) 1 99SRU0003 19
QUINCAILLERIE FOURNIE AA BB DD EE Vis ST4x15mm 3+1 Vis ST4x20mm 1+1 Vis ST4x30mm 1+1 Vis ST4x30mm 4+1 FF GG HH Ancrage mural ø6x30mm 5+1 Raccords x3 Capuchon x3 OUTILS REQUIS Crayon Ruban à mesurer Lunettes de Sécurité Perceuse avec forets à céramique ø3mm (1/8po) & 6mm (1/4po) Silicone Maillet en caoutchouc Clé Allen 2.
CETTE DOUCHE EST RÉVERSIBLE • Utilisez ces instructions pour une ouverture de la porte de droite à gauche (illustration A). • Pour une installation de gauche à droite (illustration B), suivez ces mêmes instructions mais permutez l’emplacement des panneaux: effet miroir.
GUIDE D’INSTALLATION DE LA BASE (OPTIONNEL) 1 2 Montant mural Mur de tuile Base de douche Placoplâtre Ciment Bride Silicone Plancher Base de douche 3 4 Cale en bois Bride Montant mural 5 Placoplâtre Silicone 22
INSTALLATION DES RAILS MURAUX 1. Mettre le rail (B) à niveau et marquer l’emplacement des trous. 2. Retirez les rail et percez des trous guides aux endroits marqués avec un foret Φ6 (1/4po) mm. 3. Insérez les ancrages muraux (FF) en utilisant un maillet en caoutchouc. 4. Replacez les rail (B), puis les fixer avec les vis (EE). Ne pas serrer trop fortement.
INSTALLATION DU PANNEAU LATÉRAL 1-2. Insérez les joints d’étanchéité des panneaux fixes (Y) au bas des panneaux (E). Coupez le surplus tel qu’iniqué ci-dessous. 3. Insérez le panneau latéral (E) dans le rail mural (B). Ne pas fixer immédiatement, car des ajustements ultérieurs pourraient être requis.
INSTALLATION DU PANNEAU LATÉRAL 1-2. Insérez les 2 joints d’étanchéité magnétiques (F) sur la porte (G) et sur le panneau de côté (E). 3. Placez l’attache de soutiens (X) sur le panneau latéral (E), marquez l’emplacement des trous, puis faire un trous guide en utilisant un foret Φ 3mm (1/8in). 4. Fixez les supports (X) avec les vis (BB). 5. Complètement installer l’attache de soutien (X) avec une clé Allen 4mm. 6. Percez le rail du panneau fixe (E) avec un foret 3mm (1/8in) à 3 endroits. 7.
INSTALLATION DES BARRES DE SUPPORT 1-2. Installez le raccord (O) et l’ancrage pour barre de support (M) sur la barre se support (N). 3. Marquez le contour des ancrages de la barre (M). 4. Complètement retirez les barre (N). Placez les ancrages (M) à leur endroit marqué, puis marquez leur centre sur le mur. 5. Percez un trou à la marque du centre avec un foret ø6mm (1/4po). 7-8. Insérez les ancrages (FF) avec un maillet. Fixez les ancrages (M) au mur avec les vis (DD). 8-9.
SCELLAGE Assurez-vous que la porte se ferme hermétiquement et s’ouvre doucement, et que le châssis et la barre de support sont étroitement fixés aux panneaux de verre. Appliquez un scellant étanche à base de silicone sur le contour extérieur de toutes les composantes de la douche, et verticalement entre le mur, le châssis et tous les panneaux de verre). Laissez sécher le scellant pendant 24 heures. Une application inadéquate du scellant pourrait entraîner des fuites.
OVE Decors ULC Garantie LIMITÉE du produit OVE est distributeur des produits suivants: • Portes de douche (garantie de cinq ans). • Surfaces en acrylique (garantie de cinq ans contre le cloquage, le craquelage ou l’écaillage de la surface en acrylique). • Structure en acrylique de la coque (garantie de 5 ans contre les fuites d’eau à travers le stratifié en fibre de verre de la coque en acrylique).
SHELBY PANEL LATERAL 32 ITEM #667456 Medidas: milímetros [pulgadas] 3 81 ] 3 [ 2 91 4 [36 / 12 ] / 19 [48 / 1 ] / 524 [60 ] Apertura 520 / 560 [20 1/2] / [22 1/32] 1877 [73 27/32] 1877 [73 27/32] 275 [10 13/16] 425 [16 3/4] Marca CSA Una guía de instalación de vídeo está disponible en nuestro canal de Youtube. http://youtu.
INFORMACIÓN DE SEGURIDAD PRECAUCIÓN Lea cuidadosamente la siguiente información importante antes de manipular e instalar la ducha. Hay riesgo de lesiones graves mientras se manipula el producto. Para minimizar estos riesgos, sírvase notar: • Utilice siempre anteojos de seguridad y guantes durante la manipulación. • Lea y siga siempre todos los pasos en las instrucciones de instalación. • Inspeccione todo el contenido y el vidrio por daños antes de la instalación.
TABLA DE CONTENIDOS CONTENIDO DEL PAQUETE............................................................................................................................ 33 CONTENIDO DE HARDWARE.......................................................................................................................... 34 HERRAMIENTAS NECESARIAS...................................................................................................................... 34 REVERSIBILIDAD DE LA DUCHA.........................
CONTENIDO DEL PAQUETE M N O B E Y X 32
CONTENIDO DEL PAQUETE PARTE# DESCRIPCIÓN CANTIDAD CÓDIO B Riel de aluminio 1 99STR1047-WM E El panel lateral 1 99SG10028-WM M Anclaje de la barra de soporte 1 99SGC1046-WM N Barra de soporte (largo) 1 99SGS1020-WM O Abrazaderas fijas de panel 1 99SGC1045-WM X Mordazas para paneles de vidrio 1 99SGC1044-WM Y Tira de sellado inferior para panel de vidrio (largo) 1 99SRU0003 33
CONTENIDO DE HARDWARE AA BB DD EE Tornillo ST4x15mm 3+1 Tornillo ST4x20mm 1+1 Tornillo ST4x30mm 1+1 Tornillo ST4x30mm 4+1 FF GG HH Tarugo ø6x30mm 5+1 Accesorio x3 Capuchón x3 HERRAMIENTAS NECESARIAS Lápiz Cinta medidora Anteojos de seguridad Taladro con brocas para cerámica ø3mm (1/8pu) & ø6mm (1/4pu) Silicona Mazo de goma Llave Allen 2.
REVERSIBILIDAD DE LA DUCHA • Estas instrucciones fueron elaboradas para una abertura de puerta de derecha a izquierda (ilustración A). • Para una abertura de izquierda a derecha (ilustración B), siga estas mismas instrucciones, pero cambie el lugar para la ubicación del riel: efecto espejo.
PAUTAS PARA LA INSTALACIÓN BASE (OPCIONAL) 1 2 Soportes Pared de baldosa Plato de ducha Tablaroca Cemento Brida Silicona Piso Plato de ducha 3 4 Madera cuñas Brida Soportes 5 Tablaroca Silicona 36
INSTALACIÓN DEL RIEL DE LA PARED 1. Nivele el riel (B) y marque las posiciones de los agujeros en el riel. 2. Retire el riel y perfore los agujeros piloto con una broca de Φ6mm (1/4 pu) en los lugares marcados. 3. Inserte los tacos (FF) de pared utilizando un mazo de caucho hasta que los tacos de pared estén a ras con la pared. 4. Vuelva a colocar y fíjelos el riel (B) con los tornillos (EE). No los apriete en exceso.
INSTALACIÓN DEL PANEL LATERAL 1-2. Inserte las tiras de sellado inferior (Y) del panel fijo en la base del panel lateral (E). Corte la parte sobrante para la abrazadera. 3. Inserte el panel lateral (E) en el riel metálico (B). No lo apriete completamente ya que se puede necesitar más ajustes.
INSTALACIÓN DEL PANEL DE LA PUERTA 1-2. Inserte las 2 tiras de sellado magnético (F) de la puerta en el panel de la puerta (G) y el panel lateral (E). 3. Coloque la abrazadera (X) del panel de vidrio (X) en el panel lateral (E), marque el lugar para el agujero y haga el agujero en la base utilizando una broca de ø3mm (1/8 pu). 4. Fije las mordazas (X) del panel de vidrio utilizando el tornillo (BB) . 5. Instale completamente la abrazadera (X) del panel de vidrio utilizando una llave Allen de 4mm. 6.
INSTALACIÓN DE LA BARRA DE SOPORTE 1-2. Instale la abrazadera (O) del panel de vidrio y el anclaje (M) de la barra de soporte sobre la barra de soporte (N). 3. Marque el contorno del taco (M) de la barra de soporte. 4. Retire completamente la barra de soporte (N). Coloque el taco (M) de la barra de soporte nuevamente sobre su marca en la pared, marque su agujero. 5. Perfore un agujero en las marcas centrales con una broca ø6mm (1/4pu). 6-7. Inserte los tacos (FF) utilizando un mazo de caucho.
SELLADO Asegúrese de que la puerta cierre firmemente y abra suavemente y que haya una conexión apretada entre el panel de vidrio y el riel al igual que con la barra se soporte Aplique silicona transparente resistente al agua alrededor del perímetro interno y externo de todos los componentes de la ducha (horizontalmente entre la parte inferior del panel de vidrio y la base, al igual que verticalmente (entre la pared, el riel y el panel de vidrio). Deje secar la silicona durante 24h.
OVE Decors ULC Garantía LIMITADA de productos OVE es un distribuidor de los siguientes productos: • Puertas de ducha (periodo de garantía de 5 años). • Superficies acrílicas (periodo de garantía de 5 contra formación de burbujas, grietas o desportilladuras en la superficie de acrílico). • Estructura de cubierta de acrílico (periodo de garantía de 5 años contra la pérdida de agua a través del laminado de fibra de vidrio del cuerpo de acrílico).