OVE INTELLIGENT TOILET Model TUVA INSTRUCTION MANUAL Thank you for choosing OVE INTELLIGENT TOILET. Please read and understand this entire manual before attempting to assemble, operate or install this product. p.
CONTENT SAFETY NOTICE ............................................................................................. p.3 WARNINGS ...................................................................................................... p.4 PART LIST ........................................................................................................ p.5 INSTALLATION INSTRUCTIONS ................................................................. p.6-8 FIRST TIME USE ...........................................
SAFETY NOTICE ATTENTION! BEFORE INSTALLING THE PRODUCT, YOU MUST READ AND UNDERSTAND CAREFULLY ALL BELOW WARNINGS. 1. It is forbidden to disassemble toilet by yourself. 2. Please do not set this product in a wet place, because it is an electronic product. If set in the bathroom, please insure that there is proper air flow. 3. Please insure that the product is set more than 0.6 meter away from the bathtub. 4. Please make sure electric power is AC 110V +/- 10%.
WARNINGS Do not leave the toilet exposed to the sun. May cause yellowing or color fading. To prevent against power surge damages, make sure the ground is working in the power socket. Direct sunlight affects the good functioning of the remote. Radio or transmitting devices may interfere with the toilet’s remote control functions If you do not plan to use the toilet for a long time, close the inlet water valve and unplug the toilet.
PART LIST G Clockwise - Higher flow Anti-cloclwise - Lower flow M A H I B J C D K N F E L Item Qty # A Light Indicator Panel 1 99TOI0115OU B Water Inlet 1 -- C Side Control Panel 1 99TOI0117OU D Water Supply Hose 1 99TOI0118OU E Water Filter 1 99TOI0138-OU F Inlet Fitting & Valve 1 99TOI0120OU G Seat 1 99TOI0121OU H Remote Receiver 1 -- I Battery Enclosure 1 99TOI0123OU J Manual Flush Button 1 99TOI0124OU K Nozzle 1 99TOI0125OU L Seal ring 1 99TOI012
1 INSTALLATION INSTRUCTIONS 2 B A Remove the seat from the ceramic base. Simply pull the seat up gently. Be careful, there are wires that need to be disconnected before you can remove the seat completely (see step #2). Unplug the electrical cord and the water tube before completely pulling away the toilet seat. 2A 2B 3 2 1 Unplug the cord. 3 To unplug the water tube: 1) Remove the blue clip. 2) Push the ring down with your fingernail.
5 INSTALLATION INSTRUCTIONS 6 Position the toilet on the floor drain, making sure the fixing bolts are aligned with the toilet’s holes. Insert the ring gasket under the toilet. 7 8 Using a ratchet, tightly screw the nut to the fixing bolts. Reconnect the electrical cord. Make sure both ends are well aligned. 9 10 1 2 Reconnect the water tube: 1) Gently, but firmly push the tube inside the hole. 2) Re-insert the blue clip. With care, re-install the seat on the ceramic base.
INSTALLATION INSTRUCTIONS 11 Connect the water inlet fitting to the water supply. Then connect the valve. Finally connect the flow regulator to the valve. 12 Connect the flow regulator outlet to the toilet’s water inlet with the supplied flex-tube. 13 24h Apply silicone around the base of the toilet. Wait for 24h for it to dry. p.
FIRST TIME USE 1 Open the water supply inlet valve. 2 Plug the toilet in the power socket. 3 The toilet’s blue light will start blinking. The blinking light indicates that the wash tank is filling with water, a sensor in the toilet will stop the filling process automatically after around 3 minutes when the tank is full of water. After the wash tank is filled with water, the indicator light will stop blinking. 4 The toilet will turn ON automatically.
CONTROLS DESCRIPTION SIDE CONTROL PANEL POWER/ECO: Press 1 time, it will turn the toilet ON. Press 2 times, it will activate the ECO MODE. Press 3 times, it will turn the toilet OFF. STOP: Pressing this button will stop any ongoing function. BIDET/MOVE: Pressing this button will initiate the Static Bidet Cleaning function. Press it again to change to the Back-&-Forth Bidet Cleaning function. *The Bidet refers the 5 water jets function of the nozzle.
CONTROLS DESCRIPTION WATER TEMP: Pressing this button will cycle through the 4 possible temperatures settings for the Spray/Bidet cleaning water jets. 4 settings: Room temp / 34C (93F) / 37C (99F) / 40C (104F) AIR TEMP: Pressing this button will cycle through the 4 possible temperatures settings for the air drying function. 4 settings: Room temp / 35C (95F) / 45C (113F) / 55C (151F) SEAT TEMP: Pressing this button will cycle through the 4 possible temperatures settings for the seat heating.
FEATURES SPRAY CLEANING (1 WATER JET) This function will only work if the user is sitting on the toilet. Press the SPRAY/MOVE button for spray cleaning. Water will spray and clean the user. Press the button again and the nozzle will move back & forth to insure the cleanest result. You can use this key stoke to get the best cleaning effect. BIDET CLEANING (5 JETS OF WATER) This function will only work if the user is sitting on the toilet. Press the BIDET/MOVE button for bidet cleaning.
INTELLIGENT FEATURES ECO MODE ECO MODE will cut down the electricity usage of your intelligent toilet during times of none-usage. The cleaning water tank will start heating the water only once the user is sitting on the toilet, whereas in normal mode, the cleaning water is kept to your preferences for your instant enjoyment. SOFT CLOSE DESIGN The toilet seat and seat cover have a soundless soft close design that prevents them from falling rapidly and denting or scratching the toilet.
CLEANING THE FILTER Close the inlet valve, turn clockwise. Do not take out the filter before closing the inlet valve. 2 Disconnect the felx-tube turning counterclockwise and take out the filter. Clean the filter. Use a tooth brush to clean the dirt on the filter. Use a cloth to clean the dirt and deposits in the valve. 4 Install the filter back into the flex-tube. Screw the flex-tube back onto the regulator. Please tighten the filter to avoid leakage. 1 3 Use water instead of detergent.
LONG TERM STORAGE In order to prevent from any damages that may be caused from frozen toilet water, please drain away the remaining water according to the following methods. When leaving for a long time without using this toilet, please make sure to drain all the water from the toilet. 1. Close water inlet valve. 2. Unfasten and remove the water drain bolt. 3. After draining all the water, please tightly screw the water drain bolt back into place. 4.
SPECIFICATION SHEET Item Electric Load Electric Cord Remote control batteries Product’s size Outer carton’s size Content AC 120V / 1300W / 60HZ 1.2 m insulated power cord 2x 1.5V batteries 520x690x410 mm (HxDxL) 650x760x490 mm (HxDxL) Cleaning System Spray Cleaning (1 jet) Bidet Cleaning (5 jets) Water Temp Heater Capacity Cleaning Tank Capacity Overheating Safety Anti-Reflux Water amount adjustment 0.4-1.0 L/min (water pressure 0.19 MPa / 27.6 psi) Water amount adjustment 0.5-1.
MAINTENANCE & CONSUMER RESPONSIBILITIES ■■ The DISTRIBUTOR does prohibits the use of harsh abrasive cleansers on any of its products. Harsh cleansers will damage the inner workings of the toilets. ■■ For daily maintenance, use a wet cloth and a soft liquid cleaner. ■■ Never use abrasives or cleaners containing acetone, chlorine or strong bleach, scrapers, metallic brushes, nor other objects or products which can graze or tarnish surfaces.
INSTALLATION PICTURE p.
Save this manual for future reference Conservez ce manuel pour usage ultérieur Conserve este manual para futura referencia HEAD OFFICE / SIÈGE SOCIAL / OFICINA PRINCIPAL 2800 Etienne Lenoir, Laval Quebec H7R 0A3 Canada Customer service / Service à la clientèle / Service al cliente Tel.: 1-866-839-2888 Fax: 1-866-922-9990 customerservice@ovedecors.com 8:00 am - 5:00 pm E.S.