OV-Camspot Recorder 2.
TABLE OF CONTENTS 1 Important Safeguards and Warnings ...................................................................................................................... 2 2 Declaration .............................................................................................................................................................. 3 3 Product Introduction............................................................................................................................................
6.6.3Perimeter Search ................................................................................................................................ 27 6.7 Record Backup ........................................................................................................................................... 28 7 local Configuration ................................................................................................................................................ 29 7.
10.1.2 Port mapping Manually ........................................................................................................... 62 10.2 Voice Intercom......................................................................................................................................... 62 10.2.1 Summarize ............................................................................................................................... 62 10.2.2 Configuration ...........................................
3 Product Introduction 3.1 Product Overview This series DVR/NVR is a high performance network video recorder, combined with H.264 video compression, high-capacity hard disk storage, TCP / IP transmission, embedded Linux operating system and a variety of other advanced technologies in the electronic information industry, all those ensure that a high-quality, low bit rate video storage characteristics, and good system stability.
browser. Operation Mode Support various shortcut menu operation modes, on the front panel, remote control, mouse, etc；Support simple and intuitive GUI。 Intelligent analysis Support One or Two channel Intelligent Video Analysis,，such as Face detection and perimeter analysis,Intelligent linkage pictures storage, videos, external alarm Intelligent Search Data can be retrieved through the intelligent analysis of data.
1. One-window monitor mode, click this button to display assistant function: PTZ control and image color; 2. Detection areas setting(like in motion detection setup), working with Fn and direction keys to realize setup; 10 Auxiliary Fn 3. In text mode, click it to delete the character before the caret(if there is no shift on the front panel, it can switch input methods), press this button for 1.5sec to clear all of the characters; 4. In playback mode, switch the full screen; 5.
Name Multiple-Window Switch Remote Address Number Key Icon Function Mult Switch between multiple-window and one-window. Add Click it to input device number, so that you can control it. 0~9 1.input numbers（in number mode） 2.input English character（in English mode） 3.switch channel（one-window mode） Loop Pause Pause the loop state. Enter a digital larger than 10, press two-digit number: Digital Switch -/-- 1. Press the tens digit; 2. Press digital switch button; 3. Press ones digit.
Reverse 5sec In playback mode, reverse 5sec. Slow Play Multiple slow play speeds or normal playback. Forward Stop Various forward speeds and normal speed playback. ■ In normal playback click this button to stop playback. 1. Go to SEARCH interface; Play/Pause 2. In PTZ channel: ZOOM+; 3. In normal playback click this button to pause playback; 4. In pause mode, click this button to resume playback. The procedures of controlling multiple DVR by remote control: The DVR ID default is 8.
4.4 The Input Method capitalization and the input of Chinese. Click the mouse to complete the input.”← “represents the backspace and “_ “represents a space. In the input box, you can select figures, symbols, English The input interface of English： figures： The input interface of Chinese： 4.5 Icon 4.5.1 The Screen Icons ：The channel is recording. ：The video of the channel is lost. ：Motion detection occurs. ：The channel is in monitoring and locked status.
4.5.2 Operation Icons ：Not selected. ：Be selected. ：The drop - down button ：Leave the interface. ：Cancel the settings. ：Set parameters. ： Save parameters. ：Restore the factory settings. ：Apply current settings to the system. ：Copy current settings to other channels. ：Enter the configuration interface. ：Select and configure the processing operation triggered by video detection or alarm. 5 Installation 5.1 Unpacking Inspection When you receive the product, check according to the packing list in the box.
5.3 Installation of the burner Installation Preparation Prepare a Cross Screwdriver. Steps Unscrew the screw on the side of the chassis and open the case cover. Use a screwdriver to remove the bracket fixed in middle of the disk. Open the front panel door and remove the baffle inside. Connect the burner data cable and the power cord. Fix the chassis cover. Caution The installation of the built-in burner is only for specific DVR and affects disk space for installation and interfaces. 5.
Examples of alarm input connections The alarm input is the switch quantity input. If the alarm input signal is not switch quantity signal but voltage signal, refer to the following connection: Alarm Input Devices Relay NVR In （Power Output） Alarm Switch Signal G ALM(+) ALM(-) Examples of alarm output connections When the alarm output connect with DC and AC load, please refer to the connection.
5.5 POE Connection Non-safe voltage 48V, please pay attention to electrical safety.Supply the NVR with the 12V DC power. IP Camera should support the POE. The theoretical distance of POE power supply should below 100 meters.
6 Basic Operations Guide 6.1 Power On and Off 6.1.1 Power On Install the DVR/NVR correctly (as above) and then connect the power. The DVR/NVR LED should light up and the DVR/NVR will boot automatically. The DVR/NVR will then automatically detect any connected hardware (cameras, monitors, etc.), this process should last about 30 Seconds. When this process has been completed the DVR/NVR will enter the multi-screen real-time surveillance mode.
6.1.4 Power recovery Reboot after an outage or forceful shutdown, DVR will save the record before outage and return to the normal operation mode. 6.2 Start-up wizard Quickly configuration, including P2P account&password setting, network configuration, intelligent mode selection. Help Information [QR code]From left to right: Web access address, Android APP address, iphone APP address. [Network Connection Status]The current network status. [P2P]P2P account&password setting.
[DHCP]Tick DHCP Enable. [IP address]Enter the number or press up&down button （ ） to change the IP address and[Subnet Mask]and[Gateway]。 [First DNS Server]DNS server IP. [Alternate DNS Server]DNS alternate IP. [QR code]Scan it and shows P2P account, login with mobile APP. Intelligent mode selection [Intelligent mode selection]Intelligent mode selection. 6.3 Add Device If the device supports IPC, should be added to IPC first. We offer three ways to add. And support many different protocols. 6.3.
6.3.2 Automatically added No configuration, the device is automatically added. [Main Menu]→[Configuration]→[NET channel Management]→[Open UPNP] Note：The device should support UPNP and should be in the same LAN. 6.3.3 Searching Added Search all the IPC can be added via internet and then choose to add. To do the following.
6.3.5 Modify channel configuration Enter Net channel Management menu. Click “Edit ” button of device. Click “OK” button to finish. 6.3.6 Configure Front Device Basic configuration, encoding configuration, snapshot, network and motion detection of front device can be set in NVR. Enter Net Channel Management menu. Click “Front Set ” button of device. BASIC [Channel Choose]Choose a channel. [Channel Name]Modify current channel name. [IPC Current Time]Set IPC tine. [Time Zone]Set time zone.
[Channels Choose]Choose one channel. [Code Level]H.264 [Resolution]choose main resolution and sub resolution. [Frame Rate] 1～25FPS/PAL,1～30FPS/NTSC [Bit Rate Control]Choose CBR or VBR. When choose CBR, bit rate can be set. When choose VBR, image quality can be set. [I frame interval]Set interval of adjacent frames. Max is 150. [Bit Rate]Choose 1280,1536,1792,2048,3072,4096,5120,6144,7168,8192 or set by yourself. Snapshot Refer to 7.2.1 about more details. Network [Channels Choose]Choose one channel.
:Make sure that protocol for front device supports motion detect function.All settings are for front device. 6.3.7 Delete Front Device Enter Net Channel Management menu. Click delete button or right click “device delete” to delete one device. Checkmark several device and click “Batch Delete” to finish delete. 6.3.8 Others Right click in added device. [PING]Check network status of the current channel. [Automatic Detection]Check connection status of the current channel. [Device Edit]Refer to 6.3.
:If input incorrect password three times, device will sound. If input incorrect password five times, account will be locked. For security purposes, please change the default password and the user name. Log out 1. When over the standby time, log out automatically. 2. Enter [Main Menu]-[Shutdown]-[Log out] 6.5 Preview 6.5.1 Live Preview In live monitoring, there are date, time, channel name, recording status and alarm status. Control screen switching by front panel, remote controller and mouse.
Quick Operation Switch single or multiple screens Double left click in screen to single channel and Double left click to return Adjust channel order Drag the channel to the wanted position Add device Click [+] in one channel to enter add menu. Please refer to 6.3.2 about more details. 6.5.2 Right Click Menu Enter real-time monitoring and right click menu. Screen Division Choose single screen, four screens, nine screens or sixteen screens to view. PTZ Control Configure PTZ. Please refer to 7.2.
[Tour]Enter cruise figure in box and click “Cruise” button to call cruise between points function. [Pattern]Enter patrol figure in box and click “Patrol” button to call patrol function. :gray button means don’t support the function. Configure [Present] Present is for recording the next position, which is marked by a figure. Call the figure to enable present function. Configure [Tour] Tour includes several present points and is marked by a figure. When call the figure, present point will run one by one.
[Period]Two periods can be set according to ambient light during the day and night, device will automatically switch configuration time. Need to select the Enable box. [Hue]Adjust according to image color cast [Brightness]Visual image brightness, according to the environment, reduces or increases the brightness of the image brightness to make the image relatively clear. [Contrast]Adjust image of black and white in proportion, the greater ratio, the brighter image.
The Screen Switching To implement screen switch function Above single, four, nine and sixteen channel. PTZ control Brings up the PTZ control Menu Refer to 6.4.2 PTZ control of the right-click menu. Record Search Click to select the Searching interface Refer to 6.5 Search Manual Record Click to select manual record interface Refer to 6.4.2 Manual record of the right-click menu. NET Channel Management Click to enter Net channel interface Refer to 6.
Intelligent window switch Intelligent window switch When the system is face/perimeter analysis status, click to close the intelligent window in the right side of real-time monitoring screen and click again to open it. Conceal function Color setting Refer to 6.4.2 Color setting of the right-click menu. Reset the channel order Click to reset the default channel order. Taskbar Configuration [Task Bar Mode]Choice of Resident or Automatically, Choice of Bottom and TOP. 6.6 Search 6.6.
Record Search interface description: Index Type Description 1 Choose the date Select the time and date to search records. 2 Select channels Choose the channels for querying. 3 List Display the list of recording files. It can achieve a full screen, circle playback, stopping / 4 Playback controls playing, pausing, fast playing, slow playing and the previous/next frame on a suspended state .
Achieve the playback of each channel’s record is of 5 Synchronization 6 Recoding mode 7 Time bar 8 Choose the time Search the records based on the starting time. 9 Channel number Select the channel number. synchronization in time and of consistency in operations. Choose searched recording mode, including All type, Normal, Alarm, Motion detection recording. Show the status information of channels’ video recording within one day by green, red, yellow. 128 video records are shown in the list.
6.6.2 Face Search Index Type Description 1 Play windows Play the video. 2 Play Timeline Display the progress bar of the current event 3 Playback control 4 Calendar Select the date to search records. 5 Face list Show the all face images of the channel in the query time. 6 Channel number Select the channel number. 7 Choose the time Search the records based on the starting time and end time. 8 Face Statistic 9 Page number 10 Search Click to search.
6.6.3 Perimeter Search Index Type Description 1 Synchronization Playback of each channel’s of synchronization. 2 Choose channels Select channels desired to query records. 3 Play windows 4 Event Type Play the video, it support most 4 channel playback a the same time. Select the event type,including:enter/leave area,forward/reverse cross line.
6.7 Record Backup Interface description Connect an External USB device with the USB port to backup in the “Record Backup” menu. [Detect]Identify external USB device and display the device information. [Backup]Tick the external device and click[Backup]to enter the backup menu .
7 local Configuration 7.1 The Introduction of the Main Menu The main menu is shown as the following interface: [Search]Search records by types, channels, time and playback records. [Backup]backup management. [Configuration]Including Net channel, Channel, Schedule, PTZ, Alarm and RS232. [APP Center]Set up multiple extended functions, including cloud storage, P2P, Email etc. [System]Set basic, display, storage, abnormity, status, maintain, account and Network etc..
7.2 CONFIGURATION [MAIN MENU] left click to[CONFIGURATION]： 7.2.1 CHANNEL Setting Base [Channel]to choose the channel no. which needs setting； [Channel Name]to set the channel name if in need； [Channel Display]to set the channel name’s display place on the picture； [Time Display]to set the time’s display place on the picture； [Time Synchronization]to synchronize the time with net channel and device； [Video Cover]to set some special area which needs special protection while preview and recording.
[Channel]to choose which channel to set; [Compression]H.264 [Resolution]there are multiple resolution to choose for main stream. Sub steam too. Users can set the parameter according to their needs. [Frame Rate]PAL: 1fps-25fps; NTSC: 1fps-30fps. Note：main stream, sub stream and frame rate are vary depending on devices and firmware version. [Bit Rate Control]It includes fixed stream and variable stream.
7.2.2 Recording setting Base [Video mode]Record automatically, manually or not record. [Video expiration time]The figure is between 0 to 365. [Video package time]The figure is between 5 to 120 minutes. [HDD full]Overwrite or stop recording. [Channel]Select a channel. [Video redundancy]Open or close the redundant recording. [Prerecorded]The figure is between 0 to 30 seconds. Recording plan . [Channel]select a channel. Green shows normal recording, Yellow shows motion detection, and Red shows Alarm.
[MD]motion detection recording [Alarm]alarm recording 7.2.3 PTZ setting User can set PTZ channel, protocol, address, baudrate etc. Please make sure the PTZ address and connection is correct between PTZ’s A, B wire and recorder’s A, B wire. [Channel]select a channel with PTZ camera [Protocol]select PTZ camera’s PTZ protocol(such as: PELCOD) [Address]set address, the default is 1（ not be controlled） Note：this address must be the same with PTZ, otherwise the PTZ can [Baudrate]Select the baud rate.
[Channel]Select a channel. [Alarm type]motion detection, video loss and video blind. [Motion detection]detect the motion in the picture, and send alarm according to setting. [Video loss]detect the video loss and send alarm according to setting. [Video blind]detect the video which was covered and send alarm according to setting. [Enable]control the alarm open and close [Sensitivity]highest, higher, middle, low, lower, lowest [Set area]there are totally 22*18=396 area can be set, which needs motion detection.
[Linkage Set]When a alarm occurs, you can set linkage of records, PTZ, touring and snapshot.
[Alarm input channel No.]：select a channel [Enable]：control the open and close of alarm [Type]：choose Normal open and Normal close [Process]、[Linkage set]：take 7.2.5 video detection as reference. Alarm Output On the real time preview picture, right click and choose [Alarm output], or enter[Main menu]-[Alarm]-[Alarm output] [Schedule]Alarm output is controlled by the device’s linkage setting. [Manual]Alarm output is on and the status is active. [Stop]Alarm output is off and the status is inactive.
7.2.5 RS232 [Function]Select the appropriate serial protocol [Regular]used to update firmware and adjust [Keyboard]used specialized keyboard to control the device by serial port [Transparent serial port] used to transmit serial port data transparently [Net keyboard]use specialized keyboard to control the device through network [PTZ] connect with matrix Note：some models do not have RS-232 serial port, please refer to some relative data sheet.
[DDNS] check the device setting through domain name [Email]set the sender’s email SMTP server IP address, port, username, password and sender’s mail box, mail SSL encryption. [P2P] setting of P2P transmission [Cloud] bind with cloud storage service and set synchronization rule. 7.3.1 DDNS Summary Dynamic DNS is a kind of system which point internet domain name to variable IP. According to the rule of internet domain name, domain name must associate with the fixed IP address.
Name Configuration DDNS type NO-IP DDNS Host IP dynupdate.no-ip.com port 80 Domain name xxx.xxx.org（xxx：domain name created） User name xxx（user name registered） password xxxxxx（password registered） Dyndns DDNS Register Register new account at www.dyndns.com Embedded DVR/NVR Setting Open [Main Menu]→[APP Centre]→[DDNS], choose NO-IP DDNS. Refer to the following configuration： Name Configuration DDNS type Dyndns DDNS Host IP Members.dyndns.org port 80 Domain name 7.2.6 xxx.xxx.
7.2.7 P2P [Enable]Open/Close P2P function [Transfer Mode]Network transfer strategy, choose Quality priority or Fluency priority [Account Reuse]enable it supports multiple users log in the same device [Device ID]display device ID [Password]device password [Local Port]set local port [P2P Server URL]P2P server URL [State]current connection state 7.2.8 Cloud storage Support Baidu, Dropbox and Google Drive three kinds cloud storage. Apply corresponding cloud storage account and bind it.
7.2.9 PUSH \ [Message]Open/Close the push function. [Picture]Push the message with a picture attachment [Time Lag] message push interval, 60/90/120 in option. [Test] Click to send push test information. [Event] Open/Close the push of events, including external alarm, face detection, perimeter alarm. [Device Status] Open/Close the abnormal information of device, including equipment start, no hard disk, hard disk error, recording start/stop.
area, it can’t be detected. Please set the size according to the actual usage scenarios. [Max] green square means the maximum face detection area. When the face is bigger than the maximum detection area, it can’t be detected. Please set the size according to the actual usage scenarios. [Resolution] set different analysis resolution according to the front-end highest resolution. For example, if front-end device supports 1080P, the local device can be set into 1080P, 720P, D1 or CIF resolution.
7.4 System setting 7.4.1 Basic setting Get into the [Bacical] menu under [Configuration] [System Time] set the HD record system time Note:please click the”save” button to save the time after setting [Daylight Saving Time (DST)] Enable the function and click “Set” to enter the local DST starting and ending time setting.
Select hybrid or NVR mode according the menu prompt and save. Reboot the device after channel mode modification. Channel mode introduces the device recording ability under different modes. Real recording ability needs refer to the detailed device specification. 7.4.
[Resolution]select the VGA output resolution and refresh rate, total includes 1024×720@60Hz 、 1024×768@60Hz、1280×1024@60Hz、1366×768@60Hz and 1920×1080@60Hz five choices. Tour Configuration [Enable Tour]Enable switch [Interval] Ttour interval time is 5-120s [View]It includes single screen, four-, nine-, sixteen-screen. [Motion Tour]Set the motion detection tour mode [Alarm Tour]Set the alarm tour mode 7.4.
Note: Hard disk format operation results in the loss of video data [Set]Set HDD as read-write, read only or redundancy mode. Video data can be protected from covering under read only mode. It supports HDD S.M.A.R.T smart detection at the same time.
7.4.4 ABNORMITY [Exception type] [No Disk]Alarm when HDD is not present or cannot be detected. [Disk low Space]Alarm when hard disk capacity is lower than setting. [Network Failure]Alarm when network is not connected. [IP Conflict]Alarm when IP address conflict. [Disk Error]Alarm when there is error in reading and writing hard disk.。 Process [Alarm Output]、[linkage record]、[snapshot]、[Send Email]、[show message]、[Send to network drive]、 [buzzer] 7.4.
Noted：This statistic is an estimate only for reference Online user [Online user]Online users can view the current status, disconnect and shielding. 7.4.6 Maintain System Logs: Display system logs, convenient for users to check. Log information can be divided into system operation, configuration operation, data management, alarm event, record operation, user management, log clear, file operations.
[Version]Display device serial number, system hardware features, software version and release date information. [Upgrade]System software can be upgraded: Insert a USB storage device, click Upgrade. Noted：System upgrade may cause the DVR can not start properly, please Operation under the guidance of the company's technical staff.
7.4.7 Account Basic Considerations of User Management： The following user names and user group names, etc., character and length consisting up to six bytes, the invalid string is trailing spaces. Legal characters: letters, numbers, underscores, minus sign, point, other characters are not allowed to use . the number of users and groups is not limited，User Group increased or delete according to user-defined:： The factory settings are user \ admin two groups.
Once the group belongs selected, the user's permissions only a subset of the group, not ultra vires the properties of the group. [Add User]Increases users within the group and settings user access control. [Modify User]Modify the user and settings user access control. [Add Group]Add group and settings group access control Enter into the menu interface of Increase the group, determine the group name, select 83 access control, left click mouse button to confirm, save the new user group.
[Network Card Type]LAN 1、2 can be selected by Dual LAN equipment [DHCP]Automatic search IP function. When you open the DHCP IP / Mask / Gateway cannot be located, if the current DHCP in effect, the IP / Mask / Gateway DHCP display values obtained can be found in the network state [IP Address]Use（）or input numbers to modify IP, then set [subnet mask] and [default gateway]for this IP.
Network [PPPOE]Select Enable switch to turn on the PPPOE dial-up service of the device。 Enter ISP（Internet service provider）provide the saving of user, password for PPPoE Operation：Succeed after dialing，check the [Network Status]IP, then enter the IP address to access the device after open IE。 [3G]Support 3G card dial-up to provide remote access device features。 [NTP]Select Enable switch to turn on the NTP protocol support, can be with SNTP communication server to realize automatic calibration function。 Ho
[IP Permissions] for permission to access the DVR IP rights management. When choosing the white list, the list indicates that only the IP to connect this DVR. The list of supported 64 IP settings. If the selected item is not ticked, no restrictions on access to the device's IP. [Alarm Center] alarm interface for customers to reserve the use of self-development.
router, need to set the appropriate subnet mask and gateway with router. The detail of DVR network configuration please see[Configuration]→[Network Setting] Ensure the IP is correct and check whether the DVR is on the network by using the Windows command “ping”. 8.1.2 The control installation and the user login logout Users can remote access to DVR by Internet Explorer, assuming you have a correct network configuration.
8.1.3 The Interface Of Web Operations WEB Interface Description Index Name Description 1 Channel Channel selection 2 Function key 3 Surveillance window 4 Image color & other saturation 5 PTZ control 6 Menu 8.1.
Click on 2 area in upper right corner can choose open / close the channel of the main stream or secondary stream, shows the current DVR's IP and rate information. Lower left corner shows the current video channel name. Upper right corner shows the current video time information. Click “ ”（Lower left corner of the display window）to switch between single screen and multi-screen. Lower right corner of the display window is function keys, as the following interface.
Border scan Operation: select the camera line scan of the left/right margin by direction button, and click the Settings button in the left /right margin position to determine the left border. Preset Operation: modify preset position by direction button and inputting a preset number, then click “Add” to save. Tour Operation: select “Tour”; Point between the first cruise line cruise input box value. And input numbers in “Path” and “preset”.
8.1.7 Search Record Click “Search record” to open the search interface (错误!未找到引用源。), can search and operate record, alarm, motion, local record Search record By selecting the record type, start and end times, and click the check button, get a list of files on the DVR. Select the appropriate file and download can be played Play Double click a search result to play in video window. Control the playing video by the control keys on the bottom.
8.1.8 Alarm Configuration Click the [Alarm] to enter the alarm setup menu, users can set up and operate the alarm mode,as show 5-11. If need warning message displayed and real-time pop up on the WEB interface , open the [monitor alarm], and select the appropriate type of alarm. Choose type of alarm on menu, monitor video loss, motion detection, disk full, disk error, video mask, external alarm.
10 Appendix 10.1 Port Mapping Port mapping is mapping a port of outside web host’s IP address to a machine inside web, and provide the service. When user connects to the port of the IP, the server will automatically map the request to the corresponding machine inside LAN. With this function, we can map many ports of a machine’s IP address to different machines’ different ports inside web. The port mapping can also have other special agent functions, like POP, SMTP, Telnet and so on.
10.1.2 Port mapping Manually The first step Connect the Embedded DVR to the Router, set the static IP. The second step Log in Router, enter into the configuration menu of Router, and set the menu. Then get to port, set the IP distributed by the Embedded DVR, and set the rule of port mapping, add HTTP and TCP port into mapping list.
10.3 HDD S.M.A.R.T S.M.A.R.T: “Self-Monitoring, Analysis and Reporting Technology” S.M.A.R.T HDD can analysis head, disc, motor, circuit operation, history and default security values via monitor instruction in HDD and surveillance software in host. Alarm will be sent to user automatically when the value is outside the scope of the security situation.
attribute value is 100 (for IBM, Quantum, and Fujitsu) or 253 (for Samsung). Of course, there are some exceptions, for example, some models produced by Western Digital have two different attribute values, and property value is set 200 when initial production, but after then it is changed into 100. 5、 Worst Worst value is the largest non-normal value in HDD’s running. It is a value calculate for HDD’s cumulative running, it is constantly refreshed according to running cycle, and very closed to the threshold.
Diagram 10-2 WD Download b) Click Icon to hard disk detection after downloading. c) Double click hard desk in device list, as Diagram 10-3 WD Detection: Diagram 10-3 WD Detection 10.5 HDD Capacity Calculation Reference of HDD Capacity Calculation The first time install DVR, please check if the HDD has installed. The capacity of the HDD There is no limitation of capacity of single HDD to DVR, please choose the HDD according to the saving time.
Management less than real marked. File size per hour (CBR). Bit Rate File Form 10-1 record file size Bit Rate File Bit Rate File 96k 42M 320k 140M 896k 393M 128k 56M 384k 168M 1.00M 450M 160k 70M 448k 196M 1.25M 562M 192k 84M 512k 225M 1.50M 675M 224k 98M 640k 281M 1.75M 787M 256k 112M 768k 337M 2.00M 900M File size is more unpredictable when VBR style, please refer to the real size of recording file. 10.
10.7 FAQ DVR startup failure or continuously reboot Possible reasons: 1. The system has been damaged from a bad DVR update. 2. There is a problem with the DVR main board error, please contact supplier. 3. There is an HDD error. Replace faulty HDD. Remote control does not work Possible reasons: 1. Check for batteries in remote control, especially positive and Negative. 2. Check for batteries’ power. 3. Check if remote receiver is obscured. 3 Check if DVR address corresponds to the remote address.
Diagram 10-4 IE tool bar
