WL-5470POE 802.
Declaration of Conformity We, Manufacturer/Importer OvisLink Corp. 5F., NO.6, Lane 130, Min-Chuan Rd., Hsin-Tien City, Taipei County, Taiwan Declare that the product 802.11g Hi Power Multifunction AP/Router AirLive WL-5470POE is in conformity with In accordance with 89/336 EEC-EMC Directive and 1999/5 EC-R & TTE Directive Clause Description ■ EN 300 328 V1.7.1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission equipment operating in the 2.
AirLive WL-5470POE CE Declaration Statement Country cs Česky [Czech] Declaration OvisLink Corp. tímto prohlašuje, že tento AirLive WL-5470POE je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. da Undertegnede OvisLink Corp. erklærer herved, Dansk [Danish] at følgende udstyr AirLive WL-5470POE overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. de Hiermit erklärt OvisLink Corp.
FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Hereby, Air Live, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Driective 1999/5/EC. All trademarks and brand names are the property of their respective proprietors. Specifications are subject to change without prior notification.
Table of Contents INTRODUCTION ................................................................................................................................................................ 1 FEATURES........................................................................................................................................................................ 2 PARTS, NAMES, AND FUNCTIONS................................................................................................................
Introduction . WL-5470POE is world's most popular multi-function access point. It features an impressive total of 7 wireless multi-function modes that are not available in normal access point. In addition, the ACK timeout and RSSI feature makes it suitable for long distance application. From ordinary AP application to Hotspot and WISP usage, you will find the WL-5470POE is the device you want. . WL-5470POE is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point.
Features 1. 2x100Mbps LAN ports for Wireless AP cascade.,2MB flash,16MB SDRAM. 2. TX output power is limited to 20dBm (EU), 23dBm (FCC), up to 25dBm (South America). 3. AP , Client, Bridge ,WDS Repeater, Universal Repeater mode. 4. WISP Client Router, WISP+ Universal Repeater mode. 5. Allows WEP 64/128 bit. 6. Support WPA-PSK, WPA2-PSK encryption. 7. Support data rate automatic fallback. 8. Automatic channel selection. 9. Client access control. 10. Supports 802.
Parts, Names, and Functions 1. Front Panel: LED Indicators LED Power Function Power indication Color Green Status Description Power is being applied to this product. Solid Firmware Status Turns solid green when the device is executions Green On and off indicator Link/Act. LAN port activity light turn off. Turns solid green when connected and Solid associated to at least a client station.
2. Rear Panel: Connection Ports Port Functions DC 12V Connects the power adapter plug. LAN 1 Connects inside network group. POE Power Input is available LAN 2 on LAN port 1. Press over 3 seconds to reboot this device. Reset Press for over 10 seconds to restore factory settings. Performing the Factory Reset will erase all previously entered device settings. Ant. Connects antenna.
Factory Default Settings Setting Wireless Access Point Device Name WL-5470POE SSID Default value: airlive Channel Default value: 13 WEP Default value: Disabled IP Address Default value: 192.168.100. 252 DHCP Server z In AP, Client, and Repeater mode, the default DHCP Server is disabled, Please set your PC's IP to the same subnet as the AP to access the AP. z In WISP, mode, the default DHCP server is enabled. Please restart your PC to renew the IP address. DHCP Server IP Range 192.168.100.
Hardware Connection Note: Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is placed the better will be the performance. 1. Connect to your local area network: connect an Ethernet cable to one of the Ethernet port. 2.
About the Wireless Operation Modes The WL-5470POE device provides 7 modes of wireless operational applications with: 1 2 3 4 5 6 7 Access Point Mode. Client Mode. Bridge Mode. WDS Repeater Mode. Universal Repeater Mode. WISP (Client Router) Mode. WISP + Universal Repeater Mode. This device is shipped with configuration that is functional right out of the box.
Access Point Mode When acting as an access point (default setting), this device connects all the stations (PC/notebook with wireless network adapter) to a wired network. All stations can have the Internet access if only the Access Point has the Internet connection. See the sample application below. To set the operation mode to “Access Point”, please go to “Mode JAP” and click the Setup button.