Installation Guide

Pub. No. 10011693. Printed in U.S.A. October 2009. THE PINK PANTHER
&
© 1964
2009 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color
PINK is a registered trademark of Owens Corning. ©2009 Owens Corning.
Precautions
1. WeatherLock products should be installed by a professional
roofing contractor. WeatherLock underlayment is
designed to be covered by asphalt shingles, wood shakes
or quarry slate roof assemblies. Protection from
sunlight is required to assure its long-term performance.
2. WeatherLock underlayment is a moisture and vapor barrier.
Since ice buildup is partially a function of ventilation, the
spaces under the covered deck area and the attic space
must be ventilated in accordance with FHA Minimum
Property Standards and local building codes.
3. WeatherLock underlayment is intended for exterior
application only.
4. Apply WeatherLock product directly to the wood
deck. Do not apply shingle underlayment beneath
WeatherLock product.
5. Shingles should not be installed over wrinkled or
buckled WeatherLock product.
6. Use extreme caution when installing
WeatherLock products. The WeatherLock
underlayment surface is slippery even
when dry. Use of fall protection is highly
recommended. Consult OSHA for guidelines
on fall protection
(
20 CFR 1926.500
)
.
7. For best results, apply WeatherLock underlayment
when the air temperature is over 40ºF
(
5ºC
)
but
below 100ºF
(
38ºC
)
. When temperatures are
under 40ºF, WeatherLock underlayment will
not fully adhere until warmer temperatures.
Store at room temperatures prior to installing
product in cold weather. If applied in temperatures
above 100ºF
(
38ºC
)
, it may become difficult to remove
the release poly backing. If this situation should occur,
move product into a shaded area until the WeatherLock
product is cool. Once cooled, the release poly backing
can be easily removed.
8. Store WeatherLock product in a dry, well-ventilated area.
Stand WeatherLock product upright. Do not store at
90ºF
(
32ºC
)
or warmer for extended periods of time.
When applying WeatherLock product, always follow
local building codes and the shingle manufacturer’s
instructions for installation of its product.
Precauciones
1. Los productos WeatherLock deben ser instalados por un
contratista profesional especializado en la instalación de techos.
El impermeabilizante WeatherLock está diseñado para cubrirse
con un montaje para techos de tejas de asfalto, tejas de madera
y tejas de pizarra. Es necesario proteger el material del sol con
el fin de mantener un buen desempeño a largo plazo.
2. El impermeabilizante WeatherLock es una barrera contra el
vapor y la humedad. Dado que la acumulación de hielo está
relacionada con la ventilación, los espacios debajo del área de
la base del techo cubierta y del ático deben ventilarse siguiendo
los estándares de propiedad mínimos FHA y los códigos de
construcción locales.
3. El impermeabilizante WeatherLock sólo debe usarse en
aplicaciones exteriores.
4. Aplique el producto WeatherLock directamente sobre la base
del techo. No coloque una membrana para tejas debajo del
producto WeatherLock.
5. Las tejas no deben instalarse sobre un producto WeatherLock
arrugado o abultado.
6. Tenga mucho cuidado al instalar productos WeatherLock.
El impermeabilizante WeatherLock es muy resbaladizo
aun cuando está seco. Se recomienda el uso de un
sistema de protección contra las caídas. Para obtener
las Pautas sobre la protección contra las caídas,
consulte las regulaciones OSHA (20 CFR 1926.500).
7. Para lograr los mejores resultados, aplique WeatherLock
cuando la temperatura ambiente supere los 40ºF (5ºC) pero
sea inferior a los 100ºF (38ºC). Cuando la temperatura es
inferior a los 40ºF, el WeatherLock no podrá adherirse
hasta que la temperatura aumente. Almacene a
temperatura ambiente antes de instalar el producto
en climas fríos. Si se aplica en temperaturas superiores a
los 100ºF (38ºC), es posible que sea difícil retirar el papel
antiadherente. Si esto ocurre, traslade el producto a un área
con sombra hasta que el WeatherLock se enfríe. Una vez que
se enfría, será fácil sacar el papel antiadherente.
8. Almacene el producto WeatherLock en un lugar seco y bien
ventilado. Guarde el producto WeatherLock parado. No lo
almacene a temperaturas superiores a los 90ºF (32ºC) por
períodos de tiempo prolongados. Al instalar el producto
WeatherLock, siempre cumpla con los códigos de construcción
local y siga las instrucciones del fabricante para la instalación
de este producto.
OWENS CORNING ROOFING AND ASPHALT, LLC
ONE OWENS CORNING PARKWAY
TOLEDO, OHIO, USA 43659
1
-
800
-
GET
-
PINK
®
www.roofing.owenscorning.com
For more information on Owens Corning
Roofing products,
or any of our wide range of building products and systems, it’s easy to reach us:
1
-
800
-
GET
-
PINK
®
|
www.roofing.owenscorning.com
SELF
-
SEALING ICE & WATER
RLOCK
®
MAT AND WEATHERL
R
IER WEATHERLOCK
®
G, WEA
T
E WEATHERLOCK
®
FLEX
,
WE
E
R WEATHERLOCK
®
MAT
WEA
E
R AND WEATHERLOCK
®
WE
WA
TER COLD CLIMATE SELF
-
S
M
AT SELF
-
SEALING ICE WEA
K
®
G
,
& WATER BARRIER WEA
C
K
®
FLEX
,
WEATHERLOCK
®
MA
C
OLD CLIMATE SELF
-
SEALIN
W
EATHERLOCK
®
G
,
WEATHER
R
LOCK
®
MAT AND WEATHERL
S
ELF
-
SEALING ICE & WATER
G
,
WEATHERLOCK
®
FLEX
WE
H
ERLOCK
®
COLD CLIMATE SE
WeatherLock
®
Self-Sealing
Ice & Water Barrier
Installation Instructions
Barrera autosellante contra el agua
y el heilo WeatherLock
®
Instrucciones de instalación

Summary of content (4 pages)