Duration Series Shingles Installation Instructions ™ Instrucciones Para La Instalación De Tejas Duration™ Series DURATION SERIES SHINGLES ™
Application Instructions Instrucciones de aplicación Before installing this product, check local building codes for their roofing requirements. Antes de instalar este producto, consulte los códigos de construcción locales para informarse sobre los requisitos de techado. These shingles are designed for new or reroofing work over any properly built and supported wood roof deck having adequate nail holding capacity and a smooth surface. Check local building codes.
1 Specialty Eave Flashing: WeatherLock® Underlayment or equivalent eave and flashing membrane applied to a point at least 24'' beyond interior wall line. See manufacturer’s installation instructions where required by code. See Fig. 1. Fig. 1 Specialty Eave Flashing Revestimiento especial para alero 1 Membrana autoadhesiva WeatherLock® o membrana equivalente para alero y bordes aplicada en un punto al menos 24 pulg. más allá de la línea de la pared interior.
Shingle Fastening: Standard Fastening Pattern See Fig. 4. Fasteners must be placed in the SureNail® fastening area. See Fig. 4. 4 Standard Fastening Pattern Esquema de fijación estándar Fig. 4 4 Nail Pattern Esquema de 4 clavos 1" 1" Esquema de fijación en pendientes pronunciadas o mansardas 12" 12" Place fasteners 61⁄8" from bottom edge to secure both layers of the shingle. See Fig. 4A. 55⁄8" Exposure 5 5⁄8 pulg.
Shingle Application (cont.): Starter Course: Use starter roll or trim 55⁄8" from the starter course shingle. Trim 61⁄2" off the rake of the starter course shingle and flush with the drip edge along the rake and eaves edge, and continue across the roof. Use 5 fasteners for each shingle, placed 2" to 3" up from eaves edge. See Fig. 5. (If no drip edge is used, shingles must extend a minimum of 1⁄2" and no more than 1" from rake and eaves edge.
5 Shingle Application (cont.): Fourth Course: Remove 191⁄2" from the left end of this shingle and apply the remaining piece over and above the third course shingle and flush with edge of the third course with 55⁄8" exposure. See Fig. 5D. Fasten securely according to fastening instructions. See Fig. 4. Fifth Course: Remove 26" from the left end of this shingle and apply the remaining piece over and above the fourth course shingle and flush with edge of the fourth course with 55⁄8" exposure. See Fig. 5E.
6 Valley Construction: Closed-Cut Valley See Fig. 6. A closed-cut valley can be used as an alternative and is applied as follows: Lay a 36"-wide valley liner of selfe urs adhered membrane underlayment or Co 6thilera 6 urse o C equivalent.H A 36"-wide minimum 50-lb. 5 5thilera urse H Co 4 smooth surface eroofing can also a s 4thilerroll r u H Co e be used as a valley 3rdilera 3liner. urs H Co 2nd ra 2 Fig. 6 Closed-Cut Valley Construction Construcción con canal de corte cerrado 6" Min.
For more information on Owens Corning roofing products, or any of our wide range of building products and systems, it’s easy to reach us: 1- 800 - GET- PINK | www.owenscorning.com ™ OWENS CORNING ROOFING AND ASPHALT, LLC ONE OWENS CORNING PARKWAY TOLEDO, OHIO, USA 43659 1- 800 - GET- PINK™ www.owenscorning.com Pub. No. 10003274-A. Printed in U.S.A. March 2008. THE PINK PANTHER™ & ©1964 –2008 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning.
