Installation Manual

ManualsBrandsOxbox ManualsCentral Air Conditioners8 kW Heat Strip for 2-5 Ton Heat Pump Package Units

ELECTRIC HEATER ACCESSORY

JAYHTR1P05BKRAA JAYHTR1P08BKRAA JAYHTR1P10BKRAA

JAYHTR1P15BKRAA JAYHTR1P20BKRAA

INSTALLATION INSTRUCTIONS

WARNING

These instructions are intended as an aid to qualified licensed service personnel for proper installation,

adjustment and operation of this unit. Read these instructions thoroughly before attempting installation

or operation. Failure to follow these instructions may result in improper installation, adjustment, service

or maintenance possibly resulting in fire, electrical shock, property damage, personal injury or death.

RECOGNIZE THIS SYMBOL AS AN INDICATION OF IMPORTANT SAFETY INFORMATION

DO NOT DESTROY THIS MANUAL

Please read carefully and keep in a safe place for future reference by a serviceman.

Summary of content (10 pages)

PAGE 1
INSTALLATION INSTRUCTIONS ELECTRIC HEATER ACCESSORY JAYHTR1P05BKRAA JAYHTR1P08BKRAA JAYHTR1P10BKRAA JAYHTR1P15BKRAA JAYHTR1P20BKRAA RECOGNIZE THIS SYMBOL AS AN INDICATION OF IMPORTANT SAFETY INFORMATION WARNING These instructions are intended as an aid to qualified licensed service personnel for proper installation, adjustment and operation of this unit. Read these instructions thoroughly before attempting installation or operation.
PAGE 2
FOR 20KW ELECTRIC HEATER MINIMUM CLEARANCE OF 1" ALL SIDES FOR THE FIRST 3’ AND ZERO INCHES THEREAFTER, FOR ALL OTHER HEATERS, ZERO INCH CLEARANCE ALL OF DUCT. FLEXIBLE DUCT COLLAR 3´ Fig.1 CLEARANCES 1. INSPECTION As soon as unit is received, it should be inspected and noted for possible shipping damage during transportation. It is carrier’s responsibility to cover the cost of shipping damage. Manufacturer or distributor will not accept the claims from dealer for any transportation damage.
PAGE 3
4. COMPONENT LOCATION Condenser fan motor Highly efficient enhanced copper tube/Aluminum fin outdoor coil Highly efficient enhanced copper tube / aluminum fin indoor coil Decorative protective coil guard Electric heater assembly (optional) Compressor Heavy gauge removable base rails Blower motor with slide-out blower assembly * The above figure for reference purpose only. 5. INSTALLATION Install the electric heater accessory as follows: FIG.A 1. Disconnect all electric power supplies to the unit.
PAGE 4
FIG.C FIG.D 3. Remove electric heat kit wiring panel by removing two screws. (See Fig. C&D) 4. From blower plenum, remove two screws (four screws for JAYHTR1P15BKRAA/JAYHTR1P20BKRAA) and cover plate that you can discard after heater is installed . (See Fig. E or F) FIG.E (for JAYHTR1P05BKRAA/ JAYHTR1P08BKRAA/JAYHTR1P10BKRAA) FIG.
PAGE 5
FIG.G 5. Slide electric heater into the slot. Ensure heater support rod be placed into the hole of blower compartment. (See Fig. G) Place heater rod into the hole of blower compartment 6. Carefully align the plate of electric heat kit with the holes of the blower plenum, use the screws removed in step 4 and Accessory pouch, then tighten the screws to hold the electric heat kit to the plenum. (See Fig. H or I) FIG.H (for 24/30/36K) 6 FIG.
PAGE 6
7. Tighten wires with clips in the bar, and bundle loose wires with fastening belt . (See Fig. J&K) Clip FIG.J FIG.K FIG.L 8. Use the screws in Step 3 to reinstall wiring panel. . (See Fig.
PAGE 7
9. Secure electric heat kit electric control installation board with two screws provided. (See Fig. M or N) FIG.M (for 24/30/36K) screws FIG.
PAGE 8
10.High Voltage Supply for heater kit must be routed through separate H.V. Knockout, See Fig. A for location. 11. Carefully inspect all wire connections and secure any loose wiring. 12. Remount the panel. 13. Restore all power supply. WARNING FIRE, ELECTRICAL SHOCK, HAZARD After re-connecting all wires ,check all screws of breaker and make sure all screws are properly tightened . Failure to do so will result in breaker malfunction,fire,death, personal injury or property damage.
PAGE 9
10 208/230-1-60 208/230-1-60 208/230-1-60 208/230-1-60 208/230-1-60 208/230-1-60 J4PH4024A1000AA J4PH4030A1000AA J4PH4036A1000AA J4PH4042A1000AA J4PH4048A1000AA J4PH4060A1000AA 024/030: Rotary compressor 036/042/048/060: Scroll compressor Volt Unit Model 21.5A 17.3A 15.2A 13.0A 12.0A 8.45A RLA 125A 108A 112.3A 75A 59.93A 34.8A LRA 34.3A 28.5A 24.8A 22.9A 21.7A 14.87A MCC Compressors (each) Table 6-1: Electric Heat Circuit Ratings 6. SPECIFICATION 1.67A 1.67A 1.
PAGE 10
7.