ID2018 Instruction Manual Tareq Edition revision 1
INDEX Chapter 1 - Specifications ..................................................................................................................................................................................................................................................................................... Chapter 2 - Important Notes .............................................................................................................................................................................
Chapter 1, Specifications VERY IMPORTANT NOTE: - Visit the Oxy Heli web site www.oxyheli.com to download the latest version of the manual. - Inside Box 3 you will find your serial number card. Please take a moment to visit the Oxy Heli web site and follow the instructions to register your helicopter and serial number. - It is important you take few minutes to register your helicopter and serial number with us.
IMPORTANT NOTE: This model helicopter has been designed and produced to be a high performance 3D machine. With its simple design and low parts count, pilots of all skill levels will appreciate its easy repairability. This is not a toy. Please take care assembling the model, and take care and responsibility when you fly it. We take no responsibility for any damage or injuries, either direct or consequential, from the use of this product.
Chapter 3, Required Tools for assembly TOOLS REQUIRED Small Tip - Flat Screw Driver 1.5mm Hex Screw Driver (High quality) Two Tools Required 2.5mm Hex Screw Driver (High quality) Uniball Pliers page 4 Caliper Note : We recommend high quality steel tools during assembly. Hex Screw driver in particular must have precise Tip Hexagonal dimension. 1.
Chapter 4, What's inside the box Accessories Bag Tail Boom Tail Push Rod Main Blade SERIAL NUMBER Box 1/ Bag 1 Vertical Fin Box 1/ Bag 2 Tail Rotor Box 1/ Bag 3 16T Tail Shaft Box 1/ Bag 4 Tail Pitch Slider Box 1/ Bag 5 Tail Bell Crank Box 1/ Bag 6 Tail Belt Box 1/ Bag 7 Tail Servo Mount Box 1/ Bag 8 Boom Clamp Box 1/ Bag 9 Upper Bearing Block Box 1/ Bag 10 Middle Bearing Block Box 1/ Bag 11 Lower Bearing Block Box 1/ Bag 12 Break Away Canopy Box 1/ Bag 13 Motor Mount Box 1/ Bag 14 Battery Tray Box 1/ Ba
OXY 3 POWER SYSTEM AND HEAD SPEED SET-UP.
Chapter 6: Tail Assembly Tail Case Assembly (box1/bag 1) Vertical Fin Assembly (box1/bag 1) 3x10x4 Radial Bearing OXY0401 Tail Case CA Glue 3x10x4-Flange Bearing OXY0402 Vertical Fin Important Note: This part, for tuning reasons, comes factory pre assembled, it ready to us Tail Rotor Assembly (box1/bag 2) OXY0710 - OXY4 Tail Grip Loctite 243 Important Note: This part, for tuning reasons, comes factory pre assembled, it ready to us MR63-X - 3X6X2 Radial Bearing add silicon grease TCEM2X5 - M2X5 Hex
Chapter 6: Tail Assembly Tail Pitch Slider Assembly (box1/bag 4) Tail Shaft Assembly (box1/bag 3) OXY0063 Tail Pitch Slider Haft Moon OXY0061 Tail Pitch Slider Ring MF74_2GS 4x7x2.5 flange bearing1 Important Note: This part, for tuning reasons, comes factory pre assembled, it ready to use. 16T Tail Shaft OXY0060 Tail Pitch Slider Bushing OXY0064 Link Control OXY0062 2X3X2 Bushing Important Note: This part, for tuning reasons, comes factory pre assembled, it ready to use.
Chapter 6: Tail Assembly Tail Belt Tensioner Assembly ( box1/bag5 ) Tail Belt Crank Support Assembly ( box1/bag5 ) MR63_ZZC 3X6X2.5 Radial Bearing OXY0071 Beaing Bushing MF682ZZ 2x5x2.3 Flange Bearing TBEM2x3 M2x3 Button Screw OXY0058 Tail Bell Crank Support Important note: This part comes pre assembled WITHOUT thread lock. It MUST be re-assembled with thread lock as shown. Important note: This part comes pre assembled WITHOUT thread lock. It MUST be re-assembled with thread lock as shown.
Chapter 6: Tail Assembly OXY0666-OXY4 SST Threaded Rod M2X10 OXY0716-linkage Ball M2 thread OXY0377-Carbon Rod Step 2: Note: to install this pin screw rotate counter clock wire Note Pin Screw Thread: Pin Screw Oxy designed the Pin Screw with a counter clockwise thread. This will help on the final locking operation.
Chapter 6: Tail Assembly Tensioner Assembly Tail Shaft Assembly Tail Boom Assembly 4xM2 C Washer OXY0073 Tail Case Insert ( box1/ bag6 ) OXY0072 Tail Case Cover loctite 243 loctite 243 TBEM2x5 M2x5 Button Screw before install any shim read carefully fine adjustment shims note. 4xTCEM2x5 M2x5 Hex Cap Screw TBEM2x5 M2x5 Button Screw loctite 243 B424MXL Timing Belt TCEM2x5 M2x5 Hex Cap Screw Note: all screws in this step need add loctite during assembly.
Chapter 6: Tail Assembly loctite 243 loctite 243 SCM3x3Set Screw M3x3 2 x TBEM2X5 - M2X5 Button Screw Tail Bell Crank Assembly Note: Line up the holes, so the set screw seats correctly into tail shaft lock hole.
Chapter 6: Tail Assembly A TAIL BELT ASSEMBLY AND DIRECTION CHECK: In order to check correct belt install, move belt position A CW and the position B must rotate CW. Before go forward on Tail Assembly check carefully if Belt is installed per need. Belt MUST move without any friction. 90 CCW Rotation. B Step 5-1: Tail belt is showed straight coming out, form tail boom. Be careful to check the belt if not twisted inside the boom. Use a flashlight to check inside the boom, for better vision.
Chapter 6: Tail Assembly Step 5-2: Hold carefully Tail Belt as showed and insert Front Boom Insert.A OXY0752-Front Boom Insert (Box 3/Bag ) Press in this insert parts into Tail Boom to help Tail Belt doesn't twist in the next installation step Step 5-3: Final Tail Belt Direction Check: Pull Tail Belt (as shown) and check the tail hub rotates in the direction shown. If the Tail Rotor rotates in the wrong direction, go back to the previous instructions and double check your assembly.
Chapter 7: Main Frame Assembly Boom Clamp Assembly ( box1/bag8) OXY0022-Lock Rod OXY0388 AL Pulley Guide Belt OXY0002 Boom Clamp OXY0023 Pin 2X13.
Chapter 7: Main Frame Assembly Break Away Canopy Assembly ( box1/bag 12 ) Lower Main Shaft Bearing Block ( box1/ bag 11 ) 4x10x4 Radial Bearing OXY0385 Canopy Mount TCEM2x5 M2x5 Hex Cap Screw OXY0033 Break Way Canopy OXY0083-Lower Main Shaft Bearing Block Motor Assembly (box1/bag 13) Pinion ( box1/bag13) TCEM3X8 M3x8 Hex Cap Screw OXY0029 Motor Mount ( box1/bag 13 ) 3 SCM3x3 Set Screw M3x3 16 11 This hole is in the nose of helicopter page 16
Chapter 7: Main Frame Assembly Upper Bearing Block Assembly 6 x M2 C Washer TCEM2x5 M2x5 Hex Cap Screw Middle Bearing Block Assembly Boom Clamp OXY0387 AL Stiffener Lower Bearing Block Assembly OXY0921 OXY3 Main Frame ED2018 Motor Assembly OXY0922 AL Motor Mount Stiffener ED2018 loctite 243 TCEM2x8 M2x8 Hex Cap Screw loctite 243 TCEM2x6 M2x6 Hex Cap Screw 4 x M2 C Washer 8 x M2x5 Hex Cap Screw Note: Don't fully tighten yet. Wait future neccessary assembly step.
Chapter 7: Main Frame Assembly AL Motor Mount Stiffener M2x6 Self Tapping Screw 8 x TCEM2x5 M2x5 Hex Cap Screw All Screw in this step Note: Don't fully tighten yet. See assembly alignment Step page 19.
Chapter 7: Main Frame Assembly Install main shaft with frame assembly on a flat surface, push down on both frames together and then fully tighten all M2 Hex Cap Screws (x16) holding the bearing blocks.
Chapter 8: Main Gear Assembly Main Gear Assembly ( box1/bag16 ) loctite 648 2 x MR106-ZZ Radial Bearing 6X10X2.5 2 x OXY0039 Washer 8x10x0.2 MAIN GEAR 140T OXY0037 Main Pulley Flange HF0612 One Way Bearing loctite 648 4xTCEM2x6 M2x6 Hex Cap Screw loctite 243 OXY0040 Shim Washer 6.1X8X0.1 Note: use one way sleeve to check the rotation direction of the one way bearing as shown OXY0041-One Way Sleeve Important Note: This part, for tuning reasons, comes factory pre assembled with grease and loctite.
Chapter 9: Transmission Assembly Insert Tail Assembly as shown Tail Boom Assembly page 21 Before next assembly step check carefully Tail Belt assembly position as shown
Chapter 9: Transmission Assembly Main Gear Side 7mm Head Side 93.8mm 5mm OXY0904 M2 Custom Nut Main Gear Asssembly OXY0055 2X3.5X0.5 Washer OXY0076 M2x10 Shoulder Screw page 22 In order to check the belt installation, we recommend to follow two simple steps: 1- Check with light, look inside the boom from the tail case and check the belt is only twisted 90 degrees. 2- Rotate the main gear in the flight direction (as shown) and check the tail hub rotates in the direction shown.
Chapter 10: Belt Tension & Adjustment Push down Main Shaft Collar 2 x SCM3x3 Set Screw M3x3 Loctite 243 Pull up Main Shaft - Be sure the boom is assembled and installed correctly. - Loosen the tail boom by loosening the eight M2.5x8 Hex Cap Screws. - Adjust the Belt tension by pulling on the Tail Boom. - Tighten the eight M2.5x8 Hex Cap Screws. - The belt must have good tension. We suggest re-checking after a few flights. We suggest to check belt tension often, before each flying session.
Chapter 11: Main Rotor Assembly Head Assembly. (Box 1/ Bag 17) loctite 648 F3-8G-X 3X8X3.5 Thrust Bearing 3.20 add silicon grease loctite 648 loctite 243 OXY0383 AL DFC Arm Spacer OXY0749 AL DFC Rod OXY0054 3X4X0.1 Shim 2xMR83-ZZ 3X8X2.5 Radial Bearing Important Note: This part comes pre assembled WITHOUT thread lock. Follow the instruction for final assembly. loctite 648 3 Important Note: This part, for tuning reasons, comes factory pre assembled with grease and loctite. It is ready to use.
Chapter 11: Main Rotor Assembly Important Note: This part comes pre assembled WITHOUT thread lock. Follow the instruction for final assembly Once you finish assembly, ensure the DFC Arms can rotate without friction. If the DFC Arms are assembled correctly, rotation should be smooth and without friction. In case of any friction, recheck each component and re-assembly as necessary.
Chapter 11: Main Rotor Assembly Head Assembly OXY0076-M2X10 Shoulder Hex Cap Screw TCEM2x6 M2x6 Hex Cap Screw Self Lock Nut M2 page 26
Chapter 12: Servo & Servo Rod Prepareration - You should now do some initial setup of your FBL unit and servos. - We recommend you select a new model in your transmitter, and reset your FBL unit and start with a clean setup in it as well. - After binding your transmitter to the receiver system used with the FBL unit, work your way through the FBL setup instructions to the point you plug in your servos.
Chapter 13: ESC Installation Double - side Tape ( Accessories Bag ) Be carefully Motor wire and ESC will not touch Motor/Pinion. 2 x Cable Tie Battery wires ESC Motor wires use your choice of connector rated page 28 Use 3 x cable ties, to secure the Throttle ESC wire to the main frame. Use the Frame built-in socket for best holding. In this Step connect the Motor and ESC Wires but don't secure yet. Wait till the final motor rotation check, once the FBL system is set up.
Chapter 14: Flybarless Installation Flybarless Unit Position 1 For extra FBL support we suggest to add Electronic Hook and Loop as shown. Double - Side Tape page 29 The FBL system can be installed at the bottom or top of the boom clamp. We suggest to use the bottom for easy wiring and servo removal.
Chapter 15: Cylic Servo Installation loctite 243 3 x Servo Rod Assembly loctite 243 2 x TCEM2x6 M2x6 HexCap Screw loctite 243 2 x TCEM2x5 M2x5 HexCap Screw Servo Layout Elevetor (1) Pitch (2) Aileron (pitch and aileron can be switched) (3) page 30
Chapter 16: Tail Servo Installation Leveler ( Accessories Bag ) With Rudder Stick centered and the Tail Servo Arm in the center position, adjust the Tail Push Rod length until the Tail Bell Crank and Tail Case Plate are parallel as shown. 3.5 90° Nose Left Nose Right Arm position with centered Rudder stick. The Oxy 3 Tail System has approximately 3.5 of counter torque with the Tail Bell Crank set per instructions.
Chapter 17: Landing Gear & Battery Installtion Landing Gear & Battery Installtion Main Blades Installation OXY0077-M2X14 Shoulder Button Screw Main Blades Battery Straps ( Accessories Bag ) M2 Self Lock Nut Main Blade Lock Note: In small Heli or in aggressive head design like oxy 2, 3 and 4 if you fly on hard terrain MUST set loose.This suggestion will avoid annoying wobbling on ramp up or landing.
Chapter 19: Adjustment Servo With Leveler Before Fly: Now complete the setup of your FBL system. In the Accessories Bag you will find an Oxy 4 Swash Plate Leveler. This Tool is designed to fit under the Swash Plate without disassembly any parts. This simple tool will both level the swash and give the Zero Pitch Position. Starting gyro gain: The Oxy 4 was designed around famous FBL Systems (IKON / Brain / mini V-Bar), and we suggest you start with the following standard set up and adjust after test flying.
Chapter 20: Canopy Installation Canopy Page 34
Chapter 21: Addendum - FBL Head System ( Not Included In kit ) OXY0080 -Uniball Radius Arm ( Box1/bag21 ) OXY0750-M2x15 Threaded Rod 2 x SMR628_ZZC 2.5X6X2.6 Radial Bearing OXY0716 - linkage Ball OXY0089 Pin 1.5X9.5 OXY0087Follower Arm 4.75mm 2.5X4.2X0.5 Spacer OXY0903 4mm FBL Nut Ball TCEM2x8 M2x8 Hex Cap Screw OXY0088 2x4x1.
Chapter 22: Exploded View, Main Rotor 27 14 13 12 9 11 8 23 10 25 19 22 18 24 17 20 15 4 2 3 21 26 7 5 1 page 36 6 16
Chapter 22: Exploded View, Main Frame 11 12 6 16 17 5 7 2 4 1 18 19 13 14 8 20 10 9 15 3 Page 37
Chapter 22: Exploded View, Main Frame 1 4 5 10 7 6 11 8 14 2 15 3 13 17 16 12 page 38
Chapter 22: Exploded View, Main Frame 1 21 11 24 9 19 14 20 13 12 3 6 7 45 22 23 34 10 4 18 31 2 16 39 36 44 15 41 29 17 35 26 32 8 page 39 37 38 25 40 33 28 27 30 5
Chapter 23: Spare Parts - Head Parts SP-OXY3-111 OXY3 TE - Center Hub, Black OSP-1163-OXY3-OXY4 DFC-Arm-Spacer,-2-Set page 40 OSP-1085 OXY4 Pro Edition DFC Rod Spare Set, 4pc OSP-1123 OXY3-Main-Grip-Orange-Set-2pcs SP-OXY3-003 OXY3 - Carbon Steel Spindle Shaft, 2PC SP-OXY3-004 OXY3 - Dampeners, 2 Set OSP-1119-OXY3 ED2018-TE-Swash-Plate OSP-1129-OXY3ED2018-Swashplate-Service-Bag SP-OXY3-066 OXY3 - Main Grip Service Bag OSP-1127 - OXY3-OXY4 Pro-Edition-DFC Arm,Black-Set
Chapter 23: Spare Parts - Frame Parts OSP-1008 OXY4 Linkage Ball, 10Pcs OSP-1012 Threaded Rod M2x10, 10Pcs OSP-1100 Threaded Rod M2x14, 10pcs OSP-1131 OXY3-ED-2018-FBL-System-Spare OSP-1103 - OXY4 FBL Linkage Ball, 2 Set SP-OXY3-251-1 OXY3 - Ninja Flex Blade Holder - Orange M2x10S/CS-10 Shoulder Hex Cap Screw M2x10, 10 PCS M2x10S/CS-10 Shoulder Hex Cap Screw M2x10, 10 PCS M2-SLN-10 Self Lock Nut M2 page 41 SP-OXY3-036 OXY3 - Servo Arm Set, 4 PC OSP-1130 OXY3-ED2018-FBL-System M2x6CS-10 Hex Cap S
OSP-1132 OXY3-Upper-Bearing-Block-Black OSP-1135 OXY3-Motor-Mount-Black SP-OXY3-237 OXY3 - Aluminum Pulley Guide Belt SP-OXY3-021 - OXY3 Boom Mount Lock Rod, Set SP-OXY3-067-OXY3 Main Shaft Bearing Block - Service Bag OSP-1133 OXY3-Middle-Bearing-Block-Black OSP-1135 OXY3-Motor-Mount-Black OSP-1137-OXY3 ED-2018-Main-Frame OSP-1134 OXY3-Lower-Bearing-Block-Black SP-OXY3-121-OXY3 TE - Boom Clamp Stiffener, Orange Set OSP-1138-OXY3 ED2018-Pro-Editiion-Motor-Stiffener, Orange-2Pcs
Chapter 23: Spare Parts - Frame Parts SP-OXY3-051 OXY3 - Break Away Canopy Plate SP-OXY3-104-OXY3 Carbon-Copolymer Anti Rotation Guide SP-OXY3-238-OXY3 Aluminum Canopy Mount - Black SP-OXY3-120-OXY3 TE - CNC Main Gear, 1 Set SP-OXY3-017-OXY3 One Way Hub Assembly OSP-1136-OXY3 One-Way-Hub-Service-bag SP-OXY3-016 OXY3 - Battery Tray Set SP-OXY3-015 OXY3 - Battery Oring , 4PC SP-OXY3-133 C Washer M2, Orange 20pcs M2x5CS-10 Hex Cap Screw M2x5, 10 PCS M2x8CS-10 Hex Cap Screw M2x8, 10 PCS M3x8CS-10 Hex
Chapter 23: Spare Parts - Tail Parts SP-OXY3-124 OXY3 TE - Bell Crank Support , Black page 44 SP-OXY3-034 OXY3 - Tensioner Tail Belt OSP-1146-OXY3-16T-Tail-Shaft SP-OXY3-048 OXY3 - Tail Case Hub SP-OXY3-126-OXY3 TE - Tail Case Bearing Block ,Orange OSP-1149-OXY3 Tail-Pitch-Slider,-Black OSP-1140-OXY3 ED2018-Pro-EditionTail-Bell-Crank-Orange OSP-1153-OXY3 OXY4-Tail-Grip,-Orange SP-OXY3-024-OXY3 Tail Rotor Hub - Spare Part SP-OXY3-241-OXY3 Pro Edition Vertical Fin - Black SP-OXY3-032 OXY3 - Tail C
Chapter 23: Spare Parts - Tail Parts OSP-1144-OXY3 OSP-1180-OXY3- Painted Tail Boom # 1 ED2018-Tail-push-rod-285-Main-Blade-kit SP-OXY3-025 OXY3 - Tail Rotor - Service Bag SP-OXY3-080 - OXY3 - Tail Shaft 15T SP-OXY3-028-OXY3 Tail Pitch Slider - Service Bag SP-OXY3-058-3 OXY3 - Tail Blade 47mm - Black SP-OXY3-059-3 OXY3 - Tail Blade 50mm - Black page 45 SP-OXY3-130-OXY3 TE - Tail Servo Mount, Orange SP-OXY3-108-OXY3 285 Stretch - Tail Belt Spare
Chapter 23: Spare Parts - Accessories Parts OSP-1181-OXY3 - ED2018 TE Canopy OSP-1151-OXY3 Vertical Fin Set SP-OXY3-054 OXY3 - Battery Hook & Loop, 2 Set SP-OXY3-055 - OXY3 Double Side Adhesive Tape, 2PC SP-OXY3-057 OXY3 - Cable Ties Set M3x3SC-10 Set Screw M3x3, 10 PCS M2x8SBH-10 Self-Tapping Button Hex Screw M2x8, 10 PCS M2x20CS-10 Hex Cap Screw M2x20, 10 PCS M2x6CS-10 Hex Cap Screw M2x6, 10 PCS M2x5CS-10 Hex Cap Screw M2x5, 10 PCS M2x5BH-10 Button Hex Cap Screw M2x5, 10 PCS M2.
Chapter 23: Spare Parts - Accessories Parts SP-OXY3-040 OXY3 - Pinion 11T - Shaft 3.17 OSP-1086 OXY4 Pinion 12T - 3.17mm Motor Shaft OSP-1091 OXY4 Pinion 13T - 3.17mm Motor Shaft OSP-1065 OXY4 Pinion 14T - 3.17mm Motor Shaft OSP-1088 OXY4 Pinion 15T - 3.17mm Motor Shaft OSP-1088 OXY4 Pinion 15T - 3.17mm Motor Shaft OSP-1087 OXY4 Pinion 13T - 3.5mm Motor Shaft OSP-1092 OXY4 Pinion 14T - 3.5mm Motor Shaft OSP-1066 OXY4 Pinion 15T - 3.5mm Motor Shaft OSP-1089 OXY4 Pinion 16T - 3.
