Operating instructions Artn: 3.150.
Contents I General a) Introduction b) Intended use c) Safety 4 5 6 II Controls a) The first steps / inputs and switching off b) Antenna operation c) Remote control d) Interfaces / Operation on device 8 9 10 13 III Operation of the system a) Turn on / Turn off b) Key functions 15 16 IV Operating the „Oyster® TV“ a) Begin b) Tuning c) Basic operation and FAV list d) Picture and sound e) Channel settings and channel list f) More settings g) Storage media h) Technical specificatio
I General a) Introduction This manual describes the function and operation of the automatic TV satellite reception system. Instructions regarding the installation can be found in the co-installation instructions supplied. Error-free and reliable operation can only be guaranteed if you note both for the installation and for the operation of these instructions. Your automatic satellite reception system is an intelligent system for receiving satellite television.
I General b) Intended use The intended use of this product is the fixed mounting on Mobile homes or travel trailers (caravans) with a maximum speed of not more than 130 km/h. The product is able to support the vehicle is parked, the built-in parabolic antenna automatically to one of Europe for conventional geostationary, directly beaming satellite television align fixed. The power supply must through a standards-compliant vehicle electrical system with a nominal voltage of 12V / 24V DC for one.
I General c) Safety For proper operation of your satellite system, it is basically required that the system is connected correctly to the ignition of your vehicle (see installation instructions). When correctly installed, the antenna moves when you turn the vehicle ignition automatically within a short time in the recovery position and locked there. It is for your responsibility as the driver of the motor vehicle to proof the complete retraction of the antenna before start to drive.
I General The connection to other, unsuitable battery systems can destroy the battery system, the satellite system; or can lead to a release of flammable or toxic gases or cause spontaneous ignition of improper battery systems. The manufacturer assumes no liability for any direct or indirect damages or consequential damage to the plant itself, to battery systems, motor vehicles or other goods caused of the connection to unsuitable battery systems or assembly errors or cabling errors occur.
II Controls a) The first steps The controls for the fully automatic satellite system, the Oyster® Premium TV device consist exclusively of the integrated receiver in the „Oyster® TV“ Premium and the remote control. The remote control buttons work only when the „Oyster® TV“ Premium is switched on and the initialization is complete. Switching on / off The system is the switch on the bottom of the „Oyster® TV“ Premium device on Standby and off.
II Controls b) Antenna operation In normal means of the antenna system, there is no require of any antenna operation. The system automatically searches for the corresponding satellite. The „Oyster® TV“ Premium unit is factory designed for the control of the antenna preconfigured. In case of one great location change is only recommended on the button COUNTRY enter own site. The antenna function affects only the following 4 keys on the remote control.
II Controls c) Remote Control Starts the „Oyster® TV“ Premium out of the Stand-by mode. 0-9 NUMBER / NUMBER BUTTONS: With the press of a Number 1 - 9 keys (0-9) to enter a channel directly to or make a number of adjustments in the menu. EPG EPG / ELECTRONIC PROGRAMME GUIDE. With keystroke show the current and next program information for each channel. Furthermore, a 7-day preview available. EXIT LEFT: With key press to exit the menu without Save the changes and go to the menu a step back.
II Controls NAVIGATION UP: With dedicated button brings up the next channel in the channel list. In the menu, navigate upwards. NAVIGATION LINKS: With push of a button lowers the volume the receiver. In the menu you can switch between available options to. NAVIGATION RIGHT. With push of a button to increase the volume the receiver. In the menu you can switch between available options to. NAVIGATION DOWN: With dedicated button brings up the previous Channel in the channel list. In the menu, scroll down.
II Controls STOP Stop the antenna movement START Starts the antenna movement PARK Antenna retracts. COUNTRY Location input.
II Controls d) Interfaces / Operation on device 1. Standby LED 2. Remote control sensor 3. Setup AQT Enter or exit setup menu Press and hold (more than 3 seconds) the button to start autoscan in DTV 4. VOL +/- Increases / Decreases the volume 5. CH Play Eject +/- Increases / Decreases the vhannel number To play normally or pause playing in USB To Exit in USB 6. Source Accesses the SOURCE menu 7. Standby TV standby mode 8. PCMCIA Slots for external Conditional Access (CA) - modules) 9.
II Controls Back of the TV 1 HDMI 1 / HDMI 2 2 USB jack 3 12 V / 24 V DC input terminal 4 Headphone output terminal 5 Audio in 6 Satellite input terminal 7 RF input terminal (Aerial) 8 AV input 9 Coaxial Audio out 14
III Operation of the system a) Turning on / off Attention! After turning on the antenna does extend and starts the automatic satellite search! When you turn on the „Oyster® TV“ premium device, the automatic search for satellite antenna is started. Its initialization can take up to a half of a minute. Before turning on the „Oyster® TV“ Premium make sure that when the antenna is raising, no obstacle in the way is z. Example, a branch or Garage roof. Select on the remote control just the programs you want.
III Operation of the system b) Key Functions key COUNTRY function COUNTRY ICOUNTRY Especially with a larger change of location, the alignment time of the antenna will be shortened if the correct locale is selected. The „COUNTRY“ - key invokes the menu „Select Location“ on. In this Menu are displayed for selection 47 European countries. PARK PARK STOP STOP START START PARK The „PARK“ - button retracts the antenna.
IV Operating the „Oyster® TV“ a) Switching on - START Note: Unless otherwise stated, all referneces to buttons refer to the remote control. Attention! If you turn on the „Oyster® TV“ Premium with integrated receiver, the antenna raises and starts the automatic satellite search. 1 Press the switch on the under side of the TV. The standby indicator on the front of the TV will glow red. 2 Press the Standby button on the remote control. The standby indicator will change to green.
IV Operating the „Oyster® TV“ When this screen appears, wait for the TV to tune your digital channels. This may take a few minutes. Once the auto search is completed, the TV will display the target region setting. If more than one regional transmitter is available use to select your primary region prefernece, then press OK , to leave thie menu press . EXIT Once the target region setting or Auto search is completed, the TV will display the first available digital channel.
IV Operating the „Oyster® TV“ For your convenience your 187 / 217 / 247DRS comes with a default channel list from first switch on, you are able to edit and sort this list to your own personal preference. If any further channels are required then you must start a full scan. b) To perform a full scan For your convenience your 186/21 DRS comes with a default channel list from first switch on, you are able to edit and sort this list to your own personal prefrece.
IV Operating the „Oyster® TV“ Advanced Setup By default your satellite TV will automatically scan all Free To Air or all Scramble channels on the satellite you have chosen in the Channel menu. There is however an opportunity to modify any of these auto settings in the Advanced Setup menu. It is advised not to change any default setting unless advised by qualified personnel. To enter Advanced Setup you will need to input password (default 0000).
IV Operating the „Oyster® TV“ Press scanning BLUE button, your Satellite TV will then automatically scan the new transponder and add any new channels found and add them to you channel list. FAQ - For satellite setup 1 No channels found, signal and quality bars are zero? Please check satellite dish / LNB setup, also all cables are in position correctly Confirm there is a clear line of sight to where the dish is pointing with no obst ructions, i.e. trees, buildings etc.
IV Operating the „Oyster® TV“ 3 Picture or sound is breaking up or dropping out whilst viewing? Confirm signal quality, enter Channel Search menu and check strenght and quality bars. A slight missaligment could cause a large redeuction in signal strenght. Also confrim cable quality for satellite reception and cable lenght. A long cable run could incur significant signal loss (this can be copensated with a signal amplifier / booster). Ensure dish is correct size to receive wanted signal.
IV Operating the „Oyster® TV“ c) Basic operation and FAV - List Press the button to display the source menu. The following sources are available: Source Use the buttons to scroll between inputs and press OK to select the source. If no source is manually selected using the OK button, the TV will automatically switch to the highlighted input after 15 seconds. Press the EXIT button to exit the display. The following sources can also be selected by pressing the individual buttons on the remote control.
IV Operating the „Oyster® TV“ Volume Press the V+ / V- buttons to increase or decrease the volume. The volume level will be displayed at the bottom of the screen. Mute Press the button to mute the sound. Mute will apear at the buttom left hand side of the screen. Press the button again or the V+ button to restore the sound. Mute will disappear from the screen. Favourite You can enter the Favourite menu while watching a channel by pressing the button. The following menu will appear on the screen.
IV Operating the „Oyster® TV“ Subtitle If a channel has subtitles available, you can select the subtitles by pressing the button. Select the required language using the buttons then press OK . SUBT Programminformation You can view the programme information for the channel you are watching by pressing the button. The following menu is a typical example of the programme details that will be displayed. INFO You can view the information for the next programme by pressing the button.
IV Operating the „Oyster® TV“ TV Press the TV/ button to switch between Digital TV and Digital radio modes. Menus The setup menus allow you to adjust and control the TV. 1 To accsess the on screen menus, press the button. 2 Press the buttons to navigate around the menu screens and available options. 3 To exit the setup menu press the or button. TV Setup EXIT TV Setup d) Picture + Sound This menu gives the options for adjusting the appearance of the TV picture. The following options are available.
IV Operating the „Oyster® TV“ Colour temperature Allows you to change the colour tones of the screen. You can choose from the following settings: • Normal • Warm • Cool Ton This menu gives you the options for adjusting the TV sound. The following options are available: Sound mode Allows you to select preset levels of bass and treble. You can choose from the following settings: • User • Standard • Music • Film • News Treble Allows you to adjust the treble level. Bass Allows you to adjust the bass level.
IV Operating the „Oyster® TV“ e) Channel setup and Sender List This menu allows you to adjust the channels and the channel settings. Channel Allows you to select the channel you want to adjust. Frequency Not able to be adjusted. Country Not able to be adjusted. Manual Search Allows you to manually search and tune the TV. Auto search Allows you to automatically search for channels. Channel Edit Allows you to delete, skip and add channels to the Favourite list.
IV Operating the „Oyster® TV“ Channel Edit (Satellite TV mode only) Press the buttons to select a channel. You can do the following to an Satellite channel using the coloured buttons. PAGE+ PAGE- Red Press the button to delete a channel. Use the channel to be deleted. RED buttons to select the Yellow Press the button to select the channel to be moved.
IV Operating the „Oyster® TV“ Blue Navigate to the channel you want to skip then press the BLUE button. You will no longer be able to view this channel oin normal viweing mode.
IV Operating the „Oyster® TV“ f) More settings DVB-T facility This menu allows you to change the general settings for digital TV. The following options are available. Lock - Allows you to prevent access to certain features of the TV: Note: The default password is 0000 Audio language Allows you to set the subtitle languages. Subtitle language Allows you to set the subtitle language. Time zone Allows you to change the time zone. CI Information Allows you to access the Common Interface Card and its status.
IV Operating the „Oyster® TV“ Channel Lock Allows you to prevent access to certain features of the TV. When the system Lock is ON, the password must be entered to make changes to the locked features. Lock system Allows you to lock the system. Block Programme Allows you to block certain programmes and channels. Parental Guidance Allows you to restrict programmes to suit the viewer age. Only programmes suitable for the selected age will be accessible. Select the age of the viewer from the following options.
IV Operating the „Oyster® TV“ 1 Enter the new password. 2 Re-enter the new password to confirm it. The password is now changed. Functions This menu allows you to chnage the following functions: Display Language Allows you to change the on screen display language. Aspect Ratio Allows you to change the aspect ratio. The following options are available: • Auto • zoom 1 • zoom 2 • 16:9 • 4:3 Noise Reduction Allows you to reduce / alter any noise on the images.
IV Operating the „Oyster® TV“ Sleep Timer Allows you to set the sleep timer. The sleep timer aloows you to turn the TV off after a pre-set amount of time. Press the buttons to select the required time and OK press the button to select. The following options are available: • Off • 10 Min • 20 Min • 30 Min • 60 Min • 90 Min • 120 Min • 180 Min • 240 Min Auto Sleep Allows you to turn on / off the auto sleep after four hours. Reset Allows you to reset all TV settings back to the default settings.
IV Operating the „Oyster® TV“ Electronic Programme Guide The Electronic Programme Guide displays information about current and future programmes for the hilighted channel. Press the Guide button to display the Electronic Programme Guide. The following menu will be displayed. Use the programmes. Press the days.
IV Operating the „Oyster® TV“ After finished setup, press OK to confirm. Recorder schedule list will display as below. You can delete schedule here. Press the Guide or EXIT buttons to exit the EPG. Analogue Teletext (AV mode only) Teletext is an information system that displays text on the TV screen. Using the telext control buttons you can view the pages of information that are listed in the teletext index. Note: No on screen menus can be displayed in text mode.
IV Operating the „Oyster® TV“ Mix Press the Mix button to enter mix mode. The next page will display with the picture behind it. Cancel Press the Cancel button to view the programme you are watching without any text in the background. Selecting a page 1 To select a page in text mode, find the page number you require on the Index page and enter the page number using the Numeric buttons. The number will appear in the top left hand corner of the screen. A page search will begin.
IV Operating the „Oyster® TV“ Page hold When in text mode and you are viewing a text page with sub pages, these will automatically be displayed in order with a delay to allow you to read the page. 1 Press the Hold button to stop the next subpage being displayed. The hold symbol will appear in the top left hand comer of the screen. 2 Press the Hold button again to continue moving through the sub-pages. Text enlargement 1 Press the Size button to enlarge the text shown on the text mode screen.
IV Operating the „Oyster® TV“ BLUE 4 Use the buttons to access the subject shortcuts, please note the colour buttons have same feature in satelite mode but are not shown on the screen. RED GREEN YELLOW 5 To exit digital text press the EXIT or TEXT button. Common Interface Schacht The Common Interface (CI) slot is designed to accept the Conditional Access Module (CAM) and Smart card in order to view the pay TV programmes and additional services.
IV Operating the „Oyster® TV“ Wait for a few moments until the card is activated. 1 Turn on the TV. 2 If the CAM is detected the TV will display the following message on the screen: Common Interface Module Inserted 3 Selected the relevant digital channel. 4 Detailed information on the Smart card in use is displayed. 5 Press the OK button to access the card menu. Refer to the module instruction manual for setting details.
IV Operating the „Oyster® TV“ If a signal input is not detected within 5 minutes, the TV will go into Standby mode. Audio In Please select AV as source to use with audio in (e.g. music player). After 5 minutes screen with time out, however the speaker will reamain active. g) Memory device To format your memory device and create a PVR file, press the setup key on the remote whilst in Digital TV / Satellite TV mode. Scroll down through the menu using the keys to Digital TV / Satellite TV.
IV Operating the „Oyster® TV“ 1 PVR File System Menu Select Disk will select the destination disk for recording TV program. • Check PVR file system. • Format will format the disk. • Max record time will limit the max record time. • After recording, press list button to display files information. Pressing Info button to display details. Key to abbreviations: PVR: Personal video recorder, HDD: Hard disk drive, DTV Ditial television, SD: Standard definition, HD: High definition Insert USB or HDD.
IV Operating the „Oyster® TV“ Allows you select USB disk or HDD size for recording. Pressing to change. System will show max recording time for SD and HD signal. You can‘t select definition for recordings. It‘s determined by the input signal. Select Select OK EXIT to continue. to exit. Allows you toset size for recording. For example, if USB is 4GB. System allows you select 1 GB / 2 GB / 3 GB / all by pressing Select Select OK EXIT to continue. to exit.
IV Operating the „Oyster® TV“ Press button to start recording. After recording, press List to view information on recordings. Warning: Please make sure your USB has at least 500 MB free space and the create PVR file system before you record Digital TV / Satellite TV program. You can stop recording by pressing button. In record, play and time shift mode, you can use and OK buttons to selct funtion. You can list all recorded files by pressing List button.
IV Operating the „Oyster® TV“ You can playback files in the recorded list. By pressing By pressing to stop. Press the Time Shift or OK to playback. button to enter Time hift recording mode. Press the button to enter time shift playback mode. Press button to exit. In record, play and time shift mode, you can use function.
IV Operating the „Oyster® TV“ h) Technical specifications „Oyster® TV“ ten Haaft TV sets „Oyster® TV“ - 19“ „Oyster® TV“ - 21.5“ „Oyster® TV“ - 24“ L187TRS L217TRS L247TRS B B B Display size 19“ / 47 cm 21.5“ / 55 cm 24“ / 61 cm Operating power 23 W max. 26 W max. 35 W max.
V Appendix a) Notes on the protection of the environment At the end of its lifecycle, this product must not be disposed of with your normal waste, but instead must be returned to a recycling facility for electric and electronic devices. This is indicated by the symbol on the product, the operating manual or the packaging. The materials can be reused in accordance with their identification.
ten Haaft GmbH Oberer Strietweg 8 75245 Neulingen-Göbrichen GERMANY Telefon + 49 (0) 72 37 /48 55–0 Telefax + 49 (0) 72 37 /48 55–50 E-Mail: info@ten-haaft.com Öffnungszeiten: Montag – Freitag 08:00 –12:00 Uhr 13:00 –16:30 Uhr www.ten-haaft.